Anaheim Stepper TM4500 Users Guide
Have a look at the manual Anaheim Stepper TM4500 Users Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 523 Anaheim manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 6
6
Heating Considerations
The temperature of the heat sink should never be allowed to rise above 60 degrees Celsius. If necessary,
air should be blown across the heat sink to maintain suitable temperatur\
es.
Low Voltage Adjust (VLV ADJ.)
The jumper JP4 is used to set the motor low voltage (VLV) supply which furnishes the current necessary
for holding (standstill) torque and low speed running torque. The potentiometer R9 and JP4 setting will
produce a standstill current that is 70% of the rated...](http://img.usermanuals.tech/thumb/413/6137/w64_stepper-tm4500-users-guide-1478887741_d-5.png "Page 6
6
Heating Considerations
The temperature of the heat sink should never be allowed to rise above 60 degrees Celsius. If necessary,
air should be blown across the heat sink to maintain suitable temperatur\
es.
Low Voltage Adjust (VLV ADJ.)
The jumper JP4 is used to set the motor low voltage (VLV) supply which furnishes the current necessary
for holding (standstill) torque and low speed running torque. The potentiometer R9 and JP4 setting will
produce a standstill current that is 70% of the rated...")
![Page 9
9
Troubleshooting
If a fault occurs, reset the fault by cycling power OFF for at least 20 seconds. After resetting, try to run the
motor again. If the driver faults again then check the conditions listed\
below.
Is the LED blinking twice?
This indicates that the motor has a phase shorted or there is a short in the motor cable or wiring. Check
the motor and the wiring for shorts. If the driver continues to sense “shorts” after the motor and wiring \
are
determined to be accurate, then the output...](http://img.usermanuals.tech/thumb/413/6137/w64_stepper-tm4500-users-guide-1478887741_d-8.png "Page 9
9
Troubleshooting
If a fault occurs, reset the fault by cycling power OFF for at least 20 seconds. After resetting, try to run the
motor again. If the driver faults again then check the conditions listed\
below.
Is the LED blinking twice?
This indicates that the motor has a phase shorted or there is a short in the motor cable or wiring. Check
the motor and the wiring for shorts. If the driver continues to sense “shorts” after the motor and wiring \
are
determined to be accurate, then the output...")
11 COPYRIGHT Copyright 2002 by Anaheim Automation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual, or otherwise, without the prior written permission of Anaheim Automation, 910 E. Orangefair Lane, Anaheim, CA 92801. DISCLAIMER Though every effort has been made to supply complete and accurate information in this manual, the contents are subject to change without notice or obligation to inform the buyer. In no event will Anaheim Automation be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation. Anaheim Automation’s general policy does not recommend the use of its’ products in life support applications wherein a failure or malfunction of the product may directly threaten life or injury. Per Anaheim Automation’s Terms and Conditions, the user of Anaheim Automation products in life support applications assumes all risks of such use and indemnifies Anaheim Automation against all damages. LIMITED WARRANTY All Anaheim Automation products are warranted against defects in workmanship, materials and construction, when used under Normal Operating Conditions and when used in accordance with specifications. This warranty shall be in effect for a period of twelve months from the date of purchase or eighteen months from the date of manufacture, whichever comes first. Warranty provisions may be voided if products are subjected to physical modifications, damage, abuse, or misuse. Anaheim Automation will repair or replace at its’ option, any product which has been found to be defective and is within the warranty period, provided that the item is shipped freight prepaid, with previous authorization (RMA#) to Anaheim Automation’s plant in Anaheim, California. TECHNICAL SUPPORT If you should require technical support or if you have problems using any of the equipment covered by this manual, please read the manual completely to see if it will answer the questions you have. If you need assistance beyond what this manual can provide, contact your Local Distributor where you purcha\ sed the unit, or contact the factory direct. ANAHEIM AUTOMATION April 2012