Anaheim Stepper MBC25SI1 Users Guide
Here you can view all the pages of manual Anaheim Stepper MBC25SI1 Users Guide. The Anaheim manuals for Stepper are available online for free. You can easily download all the documents as PDF.
Page 1
August 2012 L0101791 MBC25SI1 Programmable Simple Indexer/Driver User’s Guide 910 East Orangefair Lane, Anaheim, CA 92801 e-mail: [email protected](714) 992-6990 fax: (714) 992-0471 website: www.anaheimautomation.com ANAHEIM AUTOMATION
Page 2
August 2012 L0101792 Table of Contents Features.....................................................................................................................................................3 Introduction.....................................................................................................................................................3 Motion Profi les and Running the Indexer ........................................................................................................3...
Page 3
August 2012 L0101793 General Description The MBC25SI1 is a low cost single axis step motor driver integrated with a programmable simple indexer. The MBC25SI1 microstep driver/pulse generator has an output current capability of 0.5A minimum to 2.5A maximum (peak rating). The MBC25SI1 driver operates with a DC voltage of 12VDC to 35VDC. The MBC25SI1’s internal controller has four different programmable motion profi les. The MBC25SI1 also has directional soft and hard limit switch inputs, a busy...
Page 4
August 2012 L0101794 Motion Profi les and Running the Indexer: Continued Normal Operation A. A Profi le input is activated; Ramps up to max speed. B. No limit is active; Max speed is reached (keeps running at max speed). C. No Limit is active; Internal counter signals to ramp down to base speed. D. Internal Counter is complete; Base speed is reached. Pulses stop. Soft Limit Activated During Index A. A Profi le input is activated; Ramps up to max speed. B. No limit is active; Max speed is reached (keeps...
Page 5
August 2012 L0101795 LEDs When powered and operated properly, the status LED will be green. When an error occurs, the LED will change to RED and an error code will be generated in the error code register. To read and clear the error with the software, click on the “Verify Parameters” button. To read and clear the error while in “Direct Mode” use the “!” command. Once the error has been read and cleared, the LED will return to green and the error code register will be cleared. Refer to the table...
Page 6
August 2012 L0101796 Connector Descriptions Connector P5: Pin # Description 1 Motor 1, Phase 1 2 No Connect 3 No Connect 4 Motor 1, Phase 4 5 Motor Ground 6 No Connect 7 Motor 1, Phase 3 8 No Connect 9 Motor 1, Phase 2 10 No Connect Connector P2: Pin # Description 1 Power Supply Ground (0VDC) 2 Power Supply Input (12VDC - 35VDC) 3 Motor On/Off 4 Direction In 5 Profi le 4 6 Profi le 3 7 Profi le 2 8 Profi le 1 9 Ground (0VDC) Connector P3: Pin # Description 1 Clock Output 2 Busy Output 3 Hard- 4 Hard+ 5...
Page 7
August 2012 L0101797 Ordering Information Specifi cations Part Number Description MBC25SI1 2.5A Microstep Driver with integrated Programmable Simple Indexer PSAM24V2.7A Power supply for MBC25SI1 (24V @ 2.7A) CON-6404287 Optional 7 pin connector, 0.156” IDC (AMP part no. 640428-7) CON-6404289 Optional 9 pin connector, 0.156” IDC (AMP part no. 640428-9) CON-16404280 Optional 10 pin connector, 0.156” IDC (AMP part no. 1-640428-0) AA9MFC-6 6 foot serial communication cable, Male to Female Voltage...
Page 8
August 2012 L0101798 Dimensions Wiring Diagrams Two Motors One Motor
Page 9
August 2012 L0101799 Microstep Modes The microstepping modes are set by using the software when the profi les are being setup. The ranges of microstepping are 200, 400, 800, and 1600 steps per revolution in a 200 step/revolu- tion step motor. To set the divisor just select the divisor wanted (1,2,4 or 8). (Refer to Motion Tab Sheet) Setting the Output Current The output current on the MBC25SI1 is set by the on-board potentiometer R29 (Refer to Dimen- sions/Jumper and Potentiometer Locations). This...
Page 10
August 2012 L01017910 Determine Output Current The output current used for motor when microstepping is determined differently from that of a full/half step unipolar driver. In the MBC25SI1, a sine/cosine output function is used in rotating the motor. The output current for a given motor is determined by the motors current rating and the wiring confi guration of the motor. There is a current adjustment potentiometer used to set the output current of the MBC25SI1. This sets the peak output current...