Anaheim Stepper MBC25P22 Users Guide

							21
#L010142October 2003
Troubleshooting
Problem:
Can not establish communications with the pulse generator.
Possible Solutions:
1) Make sure the pulse generator has power. Is the Green LED on.
2) Check RS232 connections.
3) Check for loose cable connection either on the pulse generator or COM Port.
4) Was the software installed successfully?
5) Go to 
Setup | Communication Settings and verify COM port settings.
6) Click on 
Connect icon to communicate with the pulse generator.
7) If problems still exist, contact Anaheim Automation Tech Support.
Problem:
There is no power to the pulse generator.
Possible Solutions:
1) Is the pulse generator connected to the appropriate power supply?
2) Check for any blown fuses in line with the pulse generator.
3) If problems still exist, contact Anaheim Automation at 714-992-6990.
Problem:
The pulse generator has a fault condition.
Possible Solutions:
1) To clear an error use either the SMPG20WIN software or the direct mode command.
2) The SMPG20WIN can clear an error by clicking on the Verify Parameters button.
3) The direct mode command “!” can clear an error by prompting pulse generator to serially
     send the error code back to the user.
Example: @0!  (carriage return)
Description: Address the unit by typing @ followed by a 0 (address number) an ! (Error
        Codes Register) and a carriage return.
Note: The error code is returned in binary coded decimal format. If two errors were received
their binary values would be added together. 
						

							22
#L010142October 2003
e d o C r o r r Ee p y Tn o i t p i r c s e D
1e v e i c e R
r o r r E w o l f r e v Ol a n r e t n i n a s i s i h T . r o r r e g n i v e i c e r a d a h s n o i t a c i n u m m o c l a i r e s e h T
. r e t u p m o c e h t y b d e s u a c r o r r e
2ro r r E e g n a Re s l u p e h t o t t n e s s r e t c a r a h c f o r e b m u n d i l a v n i n a s a w e r e h T
e h t r o f d i l a v n i e r a s r e t e m a r a p e h t f i e e s o t k c e h C . r o t a r e n e g
. t n e s s a w t a h t d n a m m o c
4ro r r E d n a m m o Co t k c e h c e s a e l P . r o t a r e n e g e s l u p e h t o t t n e s s a w d n a m m o c d a b A
r o t a r e n e g e s l u p e h t t a h t r o , d i l a v s i t n e s g n i e b d n a m m o c e h t t a h t e e s
. g n i n n u r t o n s i
8ro r r E t t i m s n a r Tr o r r e l a n r e t n i n a s i s i h T . C P e h t o t k c a b t n e s s r e t e m a r a p y n a m o T
. m o r p e e e h t y b d e s u a c
6 1ro r r E r o t o Me h t t a h t e r u s e k a m e s a e l P . y l t c e r r o c n i t e s e r a s e l i f o r p d e e p s r o t o M
e r a s d e e p s e h t t a h t d n a d e e p s x a m e h t n a h t s s e l s i d e e p s e s a b
. s e g n a r d i l a v r i e h t n i h t i w
2 3s r e t e m a r a P o r e Z
r o r r Ed n a m m o c A . r o t a r e n e g e s l u p e h t o t t n e s s r e t e m a r a p o n e r e w e r e h T
r e t f a s r e t e m a r a p e e s o t d e t c e p x e t a h t r o t a r e n e g e s l u p e h t o t t n e s s a w
. d n a m m o c e h t
Error Codes
I I C S A
l o b m y Sx e H
e u l a VI I C S A
l o b m y Sx e H
e u l a VI I C S A
l o b m y Sx e H
e u l a V
e g a i r r a C
n r u t e RD 0883LC4
003993MD4
113A14R25
223B24S35
333C34U55
443D44V65
553E54!12
663G74$42
773H84_F5
ASCII Table for Direct Mode 
						

							23
#L010142October 2003
Copyright
Copyright 2003 by Anaheim Automation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a
retrieval system, or translated into any language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise, without the prior written permission of Anaheim Automation, 910 East Orangefair Lane, CA, 92801. The only exception to this would
be use of the program examples in this manual.
Disclaimer
Though every effort has been made to supply complete and accurate information in this manual, the contents are subject to change without
notice or obligation to inform the buyer. In no event will Anaheim Automation be liable for direct, indirect, special, incidental, or consequential
damages arising out of the use or inability to use the product or documentation.
Limited Warranty
All Anaheim Automation products are warranted against defects in  workmanship, materials and construction, when used under Normal Oper-
ating Conditions and when used in accordance with specifications. This warranty shall be in effect for a period of twelve months from the date
of purchase or eighteen months from the date of manufacture, whichever comes first. Warranty provisions may be voided if the products are
subjected to physical damage or abuse.
Anaheim Automation will repair or replace at its option, any of its products which have been found to be defective and are within the warranty
period, provided that the item is shipped freight prepaid, with RMA (return material authorization), to Anaheim Automation’s plant in Anaheim,
California.
Trademarks
Control Link and Driver Pack are registered trademarks of Anaheim Automation.
IBM PC is a registered trademark of International Business Machines, Inc.
ANAHEIM AUTOMATION
Torque Speed Curves