Anaheim Stepper BLD751 Users Guide
Have a look at the manual Anaheim Stepper BLD751 Users Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 523 Anaheim manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
April 2012 L010125 BLD75-1 Bilevel Step Motor Driver User’s Guide 910 East Orangefair Lane, Anaheim, CA 92801 e-mail: [email protected](714) 992-6990 fax: (714) 992-0471 website: www.anaheimautomation.com ANAHEIM AUTOMATION
April 2012 L010125 What is a Step Motor Driver? A step motor driver is a device that takes input signals (usually Clock and Direction) and translates this information into phase currents in the motor. Each time the step motor driver receives a pulse, the step motor moves one step. If the driver receives 200 pulses, the motor moves 200 steps. The motor steps at the same frequency as the clock pulses. General Description The BLD75 is a step motor driver that can drive motors rated from 1 to 7 amps/ phase (unipolar rating). It can handle 6 lead and 8 lead motors. This driver features a unipolar bilevel (or dual voltage) drive technique with short circuit, open circuit, over and under voltage, and over temperature detection (with a Fault LED and output). A transformer is required to power up the driver. Bilevel Drive The basic function of a motor driver is to provide the rated motor phase current to the motor windings in the shortest possible time. The bilevel driver uses a high voltage to get a rapid rate of current rise in the motor windings in the least amount of time. When reaching the present trip current, the driver turns off the high voltage and sustains the current from the low voltage supply. Half-Step/Full-Step Users have a choice of full-step operation of half-step operation. Full-step operation occurs by ener- gizing two phases at a time, rotating a typical motor 1.8 degrees per step. Half-step operation occurs by alternately energizing one, and then two, phases at a time, rotating the motor 0.9 degrees per step. Full-step operation is suggested for applications that specifi cally require that mode, such as when retro- fi tting existing full-step systems. Features • Unipolar Operation • 10 Amps per Phase Operating Current (Kick Current) • 7 Amps per Phase Standstill Current • 70 Volt Operation • Short Circuit, Open Circuit, High Voltage, Low Voltage and Over Temperature Fault Detection • Inputs accept 24VDC signals • Motor ON/OFF Input • Half-Step and Full-Step Operations • Bilevel Driver Operation • Fault LED, and Fault Output • Detachable Terminal Block • Compact and Rugged • Available in Driver Packs
April 2012 L010125 Clock Modes The BLD75 has two clock options: Clock and Direction, or Dual Clock operation. Jumper JP2 is used to select the clock option. Basically JP2 selects Terminal 5 as either the Direction input or the CCW input. With the Clock and Direction option (most common option), clock pulses applied to the Clock input (Termi- nal 6) cause the motor to step. The direction of the motor is determined by the logic level of the Direction input (Terminal 5). Jumper JP2 must be in the “2-3” position for this mode (see Figure 4 and Table 1). Physical direction also depends on the motor wiring. With the Dual Clock option, clock pulses applied to the Clock input (Terminal 6) cause the motor to step in the clockwise direction. Clock pulses applied to the CCW input (Terminal 5) cause the motor to step in the counterclockwise direction. Jumper JP2 must be in the “1-2” position for this mode. Either positive or negative going pulses may be used by setting jumpers in the appropriate position (see Table 1). To determine which setting to use, fi rst consider the type of clock pulse output on the pulse generator or indexer (controller). If the clock output on the controller is open-collector type (sinking), then use the negative going jumper setting. If the clock output on the controller is a pnp or p-channel (sourcing) type, then use the positive going jumper setting. If the clock output on the controller is a TTL/CMOS type (totem pole), then either setting will work; but the jumper setting should be chosen based on the level of the clock output when the controller is not pulsing, then use the negative going jumper setting. The clock inputs (Clock and CCW) are pulled up to +5VDC through a 10K resistor for negative going clock inputs; or pulled down to 0VDC through a 10K ohm resistor for positive going clock inputs. The pullups/ pulldowns are followed by an RC fi lter. See Figure 2 and Figure 3. Motor On/Off Input The motor on/off input allows de-energizing a motor without disturbing the positioning logic. After reen- ergizing the motor, a routine can continue. This reduces motor heating and conserves power, especially in a applications where motors are stopped for long periods and no holding torque is required. If holding torque is required (such as when lifting a load vertically), then the motor must stay energized.
April 2012 L010125 Jumper Functions/Locations If a fault occurs, reset the fault by applying a logic “0” to the Reset Fault Input (pin 4) for at least 100ms or by cycling power off for at least 15 seconds. After resetting, try to run the motor again. If the driver continues to fault, check the conditions listed in the troubleshooting section on page 11. Adjusting Kick Current By following the instructions on the cover, use a small screwdriver to adjust the potentiometer. Line up the potentiometer’s arrow to the number corresponding to the motors rated current (amps/phase). Fault Protection There are fi ve types of fault detection. When a fault is detected, the driver turns off the motor current, the red fault LED indicates which type of fault occurred and the Fault Output (pin 10) goes low. This output is able to stand off 50V and sink 50mA. Refer to the table below for LED fault indications. Function JP1 JP2 JP3 Negative Going Clocks 1-2 X X Positive Going Clocks 2-3 X X Terminal 5 = CCW X 1-2 X Terminal 5 = Direction X 2-3 X Low Voltage Fault Detection Enabled X X 1-2 Low Voltage Fault Detection Disable X X 2-3 Standard Product 1-2 2-3 2-3 # of LED Blinks Fault Condition 1 Short or Over Current 2 Open Motor or Connection 3 High Voltage Too High 4 Low Voltage Too Low 5 Over Temperature
April 2012 L010125 Motor Connections Figure 5 is a hookup diagram for typical BLD75 driver applications. The input signal connection must be separate from motor connections and all other possible sources of interference. IMPORTANT NOTE: When the motor cable between the driver and the step motor extends beyond 25 feet, consult the factory. Wiring Diagram The wiring diagram in Figure 5 shows the BLD75 with the AA2791 Transformer. For wiring with the AA2793 Transformer, refer to fi gure 9 Power Supply Requirements The BLD75 must be powered by a recommended Anaheim Automation transformer. The AA2791 transformer and the AA2793 transformer are the most commonly used and are both rated for 300VA. These transformers have a high voltage winding, a low voltage winding, and a logic volt- age winding. The AA2793 has two high voltage windings and two low voltage windings for power- ing two BLD75’s. The high voltage winding (yellow) and low voltage winding (red) plug into the quick disconnects on the back of the BLD75 (see hookup diagram in Figure 5). The logic voltage winding (orange) is used to power up optional controllers. When using one of these transform- ers, the nominal low-voltage is 5.0 volts and the nominal high voltage is 60V. The transformer voltages are shown in Figures 7 and 8; the physical dimensions are shown in Figure 6. For other transformers, refer to ordering information chart or contact the factory.
April 2012 L010125 Transformer Drawings Note: The AA2793 transformer is the same physical size as the AA2791, but it has two sets of secondary windings (to power two drivers) and a dual primary winding for 115/230V operation.
April 2012 L010125 Figure 9: Wiring for different line voltages for transformers with a 90-265VAC input.
April 2012 L010125 Dimension Drawings Ordering Information Chart Part Number Description AA2791B Transformer, Single Output Secondaries, 300VA, 115VAC in (Recommended) AA2793 Transformer,d Dual output Secondaries, 300VA 90-265VAC in AA2977 CE Approved Transformer, Single Output Secondaries, 300VA, 90-265VAC in AA3075 Transformer, Dual output Secondaries, 400VA, 90-265VAC in AA3361 Transformer, Dual output Secondaries, 500VAC, 90-265VAC in CBL-16AWG-06C Motor Cable, 6 Conductor, Shield, 16 Gauge, Sold per linear foot CBL-18AWG-06C Motor Cable, 6 Conductor, Shielded, 18 Gauge, Sold per linear foot
April 2012 L010125 13 Pin Terminal Description Motor Compatibility - Sample List, more motors available Add suffi x “S” for single-ended shaft, or suffi x “D” for double-ended shaft. Notes: Other motors not listed above may be compatible with this driver. Anaheim Automation carries a full-line of standard and high torque step motors. Contact the factory re- garding compatibility. See back cover for speed/torque curves. Part # Unipolar Rating 23D104_ 2.0A 23D108_ 4.0A 23D209_ 4.5A 23D309_ 4.5A 34D106_ 3.0A 34D109_ 4.5A 34D207_ 3.5A 34D213_ 6.5A 34D314_ 7.0A 42D112_ 6.0A 42D212_ 6.0A Terminal # Description 6 Lead Motor 8 Lead Motor 1 Motor, Phase 1 Red Orange 2 Motor, Phase 3 Red/White Black 3 Motor, Common 1 & 3 Black Orange/White & Black White 4 Fault Reset --- --- 5 Direction (CCW) --- --- 6 Clock (CW) --- --- 7 OVDC --- --- 8 Half-Step/Full Step --- --- 9 On/Off --- --- 10 Fault Output --- --- 11 Motor, Common 2 & 4 White Red/White &Yellow/White 12 Motor, Phase 2 Green Red 13 Motor, Phase 4 Green/White Yellow Standard Motors - D SeriesHigh Torque Motors - Y Series Part # Unipolar Rating 23Y206_ 3.0A 23Y210_ 5.0A 23Y306_ 3.0A 23Y310_ 5.0A 34Y108_ 4.0A 34Y112_ 6.0A 34Y207_ 3.5A 34Y214_ 7.0A 34Y307_ 3.5A 34Y314_ 7.0A 42Y112_ 6.0A
April 2012 L010125 Specifi cations Control Inputs (All): (Pins 5, 6, 8, 9) TTL-Compatible Logic “0” - 0 to 0.8 V Logic “1” - 3.5 to 24.0V Fault Reset: (Pin 4) Logic “1” (open) - Driver enabled and Fault detection enabled Logic “0” - Resets a Fault condition (driver is disabled when this input is low). This input must be held low for at least 100ms. Clock Inputs: (Pins 5 and 6) Pulse required; 15 microseconds minimum. The clock input is pulled up/down internally to +5VDC/0VDC through a 10k ohm resistor, based upon JP2 selection. Direction Control: (Pin 5) Logic “1” (open) - CW Logic “0” - CCW Excitation Mode Select: (Pin 8) Logic “1” (open) - Half-step Logic “0” - Full-step Power ON/OFF: (Pin 9) Logic “1” (open) - motor current on Logic “0” - motor current off Fault Output: (Pin 10) This output is an open drain output. Conducting (pulled to ground) with a fault, open under normal opera- tion. 50V Stand Off, with current sink of 50mA Max. Output Current Rating: (Pins 1, 2, 3, 11, 12, and 13) 10 Amps/phase maximum operating current, 7.0 Amps/phase maximum standstill current, over the op- erating voltage and temperature range. Motor phase ratings of 1.0 Amp minimum are required to meet the minimum kick level. Power Requirement: Anaheim Automation recommended transformer. Refer to ordering information chart. Operating Temperature: 0 to 60 degrees C It is recommended that the aluminum driver baseplate be mounted on a larger aluminum plate, or similar heat-conducting structure, whenever possible. This will prevent the driver baseplate from overheating and degrading driver reliability. Fan cooling is also recommended to eliminate hot spots on the heat sink. Fusing: A 5 Amp Fast Blow fuse in series with the primary winding of the transformer is required.