Anaheim Power Supply Kits Users Guide

							HIGH VOLTAGEYEL
YEL
REDLOW VOLTAGE
0VDC RED
ORG
AC LOGIC VOLTAGE
ORG 10VACPOWER SUPPLY KITS
ANAHEIM AUTOMATION
910 E. ORANGEFAIR LANE
ANAHEIM, CA 92801
(714) 992-6990   FAX (714) 992-0471
www.anaheimautomation.com
e-mail: [email protected]
July 8, 2002
#L010086The Bilevel Power Supply Kits in this booklet are designed to be used with Anaheim
Automation Bilevel Step Motor Drivers.  These Power Supply Kits supply drivers with a
High Voltage, a Low Voltage, and a logic voltage.  The following items should be
included with the power supply kit:
(1) Transformer
(2) Filter Capacitors *
(2) Capacitor Clamps
(2) Diode Bridges
Misc. Hardware
*See figures for values.
A typical hookup diagrams for the Power Supply Kits is shown above (specific hookup
diagrams are shown on the inside pages).  The Yellow winding is the High Voltage
Winding.  The Red winding is the Low voltage Winding, and the Orange winding is the
Logic winding.  Notice that the High Voltage is stacked on top of the Low Voltage
supply (the - terminal of the High Voltage diode bridge is connected to the + terminal
of the Low Voltage diode bridge).  It is strongly recommended tostack the power
supplies as shown in the diagrams.  
Some transformers have two windings on the primary side; these transformers can be
wired to operate on 115VAC nominal or 230VAC nominal.  The two windings should be
wired in parallel for 115VAC operation.  For 230VAC operation, the two windings should
be wired in series (see specific examples). 
Some drivers such as the BLHP101 will also require an AC Logic voltage (orange pair
winding); some drivers do not require the logic voltage (refer to the driver specifications). 
If your driver does not require this logic voltage, a +5VDC power supply can be created
from this winding to power up other circuitry (refer to figure 6).  If this winding is not
used, insulate the ends of these wires with heat shrink tubing or electrical tape.
The voltages for all power supply kits are shown in the hookup diagrams.  These
voltages shown are the NO LOAD voltages; they will drop when the driver and motor are
connected.
Below is a list of power supply kits which are compatible with the drivers listed. 
						

							0.156 HOLE, 3 PLACES
3 IN DIA, 120E APART1     IN.156 HOLE, 2 PLCS13
162.5 IN DIA, 120E APART 0.156 HOLE, 3 PLACES10,000uF  75V8,200uF 160V
58,000uF  16VDRIVERCOMPATIBLE POWER SUPPLY KITS
MBL536PSK32791Ni
MBL600PSK32791Ni
BLHP101PSK42409Ni
i STANDARD KITS
DIMENSIONSA drawing of the transformer should be included with the power supply kit.  Dimensions
of the capacitors are shown in the table below.
CAPACITORDIAMETERLENGTH
10,000uF  75V2.54.125
58,000uF  16V1.3753.125
8,200uF  160V2.05.125
The mounting hole patterns for the capacitor clamps are shown below.
FIGURE 1: Hookup Diagram for PSK32791N
     115VAC LINE VOLTAGE 
						

							figure2: Hookup Diagram for PSK32793N
w/ 230VAC line voltage 
figure3: Hookup Diagram for PSK32793N FIGURE 4: Hookup Diagram for PSK42409N
    w/ 230VAC LINE VOLTAGE
    115VAC LINE VOLTAGE 
						

							1.5A BRIDGE
ORG
ORG
2200uF
16VLM7805 IN
GNDOUT10uF
25V
+5VDC
0VDCFIGURE 6:  +5VDC @ 1 Amp Supply created      
                 from Orange Logic Windings. figure5: Hookup Diagram for PSK42409N
115 VAC LINE VOLTAGE
910 E.ORANGEFAIR LANE ANAHEIM, CA 92801
(714) 992-6990   FAX: (714) 992-0471