Anaheim Linear Actuator LS100 Table Manual

							 
  
 
 
 
 
11 
   
  
Motor 
Option  
Holding Torque  2 phases on  (oz-in) 
 
Unipolar    Bipolar   
Voltage 
per Phase 
 (V / phase) 
 
   Unipolar   
Current per Phase  (A/Phase Peak)   
                Bipolar 
Unipolar    Series   
Resistance (ohm/ph) Unipolar   
Inductance per  Phase 
(mH/phase) 
Unipolar  Shaft Options 
2A 
  55          77  3.3  1.5         1.5  2.2 2.0 Single Ended 
3A   55          77  1.8  3.0         3.0  0.6 0.6 Single Ended 
3B  126       151  2.3  3.0         3.0  0.75 1.1 Single Ended 
3C  188       226  3.0  3.0         3.0  1.0 1.6 Single Ended 
2B   55          77  Same as 2A  Double Ended 
3E   55          77  Same as 3A  Double Ended 
3F  126       151  Same as 3B  Double Ended 
3G  188       226  Same as 3C  Double Ended 
4G    -          55   
 
Refer to Litera ture #L010130 
for detailed Specifications on 
23MD Series Motor/Drivers 
http://www.anaheimautomation.com/manuals.htm 
 
4H    -          55 
4E    -         105 
4F    -         105 
4I    -         155 
4J     -         155 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
   
 
 
 
 
Ordering Information – Model Coding  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
						

							 
  
 
 
 
 
12 
 
 
 
 
 
 
 
 
Mounting  Requirements 
 
In order to achieve the published accuracy & repeatability of an LS100 Series positioning Table, 
care must be taken when mounting the table to  your surface. The mounting surface of the 
positioning table must be as flat, or flatter than the positioning table itself. If the surface is not flat, 
“shimming may be required. Proper table mounting  is essential and highly recommended so that 
the table can be supported over it s entire length and that all table base mounting holes are used. 
This will prevent the table from  deflecting over unsupported regions wh en the load travels over 
that area. It also maintains the systems rigidi ty, and prevents shortened positioning table life from 
structural fatigue. 
 
Recommended Base Mounting Screws: English mount #10-32  
Base Mounting screws are NOT provided by Anaheim Automation   
 
Cantilever Load 
It is recommended that a 1:1 ratio be used when loading the carriage of the LS100 Series Tables.  
The 3.5” Carriage Length predetermines the attach ed MAX Length that the extended load should 
rest from. 
 
 
 
 
 
 
 
 
 
 
  
						

							 
  
 
 
 
 
13 
  XY Mounting Assembly Instruction 
						

							 
  
  
 
 14 
 
Terms and Conditions 
 
Limited Warranty 
All Anaheim Automation products are warranted against defec ts in workmanship and materials, when used under normal 
operating conditions and when used in accordance with the factory’s  specifications.  This warranty is in effect for a period 
of twelve months from the date of purchase, or eighteen  months from the date of manufacture, whichever comes first. 
Anaheim Automation will repair or replace at its’ option, any  of its products found to be defective and are within the 
warranty period. Anaheim Automation is not responsible for re moval, installation, or incidental expenses incurred in 
shipping to and from the factory. Anaheim Automation is not liable, under any circumst ances, for any consequential, 
incidental or indirect damages or expenses associated with the warranted product.  Product that is damaged due to 
misuse, abuse, negligence, exposure, accident, improper insta llation or hook-up, or has been modified or dismantled, is 
NOT covered under this warranty. 
 
Open Accounts 
Anaheim Automation extends credit to Government agencies, industrial and distributor accounts with a good published 
credit rating. Companies may apply for an open account by  filling out Anaheim Automation’s Credit Application Form, or 
by supplying credit information on their company’s le tterhead to Anaheim Automation’s Accounting Department. Credit 
Information supplied by the buyer, or by others on the cu stomer’s behalf, shall become part of the Credit Application and 
any false or misleading information shall constitute fraud. A ll orders are shipped prepaid, COD, cash, wire-transfer, VISA 
or Mastercard, until an open account is established. 
 
Payment Terms for Open Accounts 
Terms are Net 30 days. FOB is Anaheim, California. 
 
Account Management and Remedies 
In the event it becomes necessary for Anaheim Automation to file suit to enforce payment of past due invoices, such a suit 
will be brought in Orange County, California.   Anaheim Automation shall be entitled to collection of fees, court costs, and 
interest at 10% per annum or such legal maximum rate as  is allowed, on all invoice amounts past due. All purchase 
agreements are governed by the laws of the State of California. 
 
Shipping 
Anaheim Automation ships UPS Ground. If the customer prefer s another carrier, or a premium routing method, this 
information must be clearly stated on the Purchase Order a nd confirmed, in writing, by Anaheim Automation. The 
customer must authorize any additional expenses that will  incur. If quoted “factory stock,” and Anaheim Automation has 
received a Purchase Order by noon PST, the order will ship the following day.  For customers with an urgent request, 
there exists a possibility to ship later the same day. Howeve r, an “expedite fee” is charged, along with any other expenses 
incurred to fulfill this request.  
 
All promises of shipment or delivery are approximated as closely as possible by Anaheim Automation, but are subject to 
delivery estimates made by our suppliers, w eather conditions, fires, strikes, disputes, accidents, delays in transportation, 
material, fuel, or labor shortages, or any other  cause beyond reasonable control of Anaheim Automation.  In no event will 
Anaheim Automation assume any responsibility fo r any delays in shipments or deliveries. 
 
Expediting Orders 
If orders must be expedited, interfering with the normal flow  of manufacturing, a minimum of a 15%  “expediting fee” will 
incur. The minimum “expediting” charge is $50.00 per order. 
 
Blanket Orders 
All Blanket Orders must be confirmed with a written Pu rchase Order, and include scheduled release dates. Any changes 
to the schedule or the quantity purchased, must be agreed upon by Anaheim Automation, Inc., and a written “Change 
Order” must be in processed to confirm such changes.  NOTE: Blanket Orders are Non-Cancelable and Non-
Returnable. 
 
Shortages or Damages 
All claims for shortages or shipment errors must be made within 15 days after the receipt of the shipment. Anaheim 
Automation’s liability is limited to the value of material value  on the invoice.  Claims for other loss or damages are filed 
against the carrier involved in the specific shipment.  
 
Discontinued Items 
Items are subject to change or discontinuance without notice. Ask a Customer Se rvice Representative for advice on any 
possible substitution for your application. 
 
  
						

							 
  
  
 
 15 
 
 
 
 
 
 
Returns (RMA) and Repairs 
Anything being returned to Anaheim Automation must have a RMA (Return Materials Authorization) number assigned by 
the factory, and it must be referenced on all the paperwork accompanying the return/repair. Items that do not reference 
the RMA number will not be processed. Do NOT return produc t using a Debit Memo.  No product will be accepted for 
Credit after 30 days from the date of shipment. Product must be shipped with freight prepaid.  Special, custom or 
modified products are Non-Returnable, and no credit shall be offered. 
 
Product in need of repair must have previous aut horization to return it to the factory. It is critical to do so, as the advice  the 
factory can offer is invaluable, and can often save the  customer money. The factory will determine upon inspection 
whether the product is covered under warranty. The factory charges a “flat-rate” fee based on model number, regardless 
of the problem found. The fee is charged for all returns, in cluding those where no problem is found, as inspection and test 
is time-consuming.   
 
Cancellations and Restocking Charges 
Cancellation of any order must be approved by Anaheim Automa tion and will be on terms that protect us from any loss. 
The restocking charge is 15% on all product returned. The  minimum restocking charge is $25.00. Returns must be made 
within 30 days of receipt of product.  Shipping expenses are  paid by the customer. All products are subject to factory 
inspection and must be in resellabl e condition to receive credit.  Special, custom and modified products are Non-
Returnable and Non-Cancelable . 
 
Engineering or Technical Assistance 
Technical assistance is available at  no charge to help the customer in choosing Anaheim Automation products for a 
specific application. However, any selection, quotation, or  application suggestion offered from Anaheim Automation, its’ 
representatives or distributors, are only to  assist the customer, and in all cases, determination of fitness for purpose or 
use are solely the customers’ responsibility. While every effo rt is made to offer solid advice and to produce technical data 
and illustrations accurately, such advice and documents are for  reference only, and subject to change without notice.  
Programming of product is the customer’s responsibility. 
 
All Sales are made pursuant to the Terms and Conditions herein, are in lieu of any other expressed or implied 
terms, including but not limited to any implied warranties.