Anaheim Discounted Package PKG233MBC12PSCBL User Manual
Have a look at the manual Anaheim Discounted Package PKG233MBC12PSCBL User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 523 Anaheim manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
910 East Orangefair Ln. Anaheim, CA 92801 Tel. (714) 992-6990 Fax. (714) 992-0471 www.anaheimautomation.com PKG-233-MBC12-PS-CBL System Diagram and Specifications L010867 Included Components: 23Y310S-LW8-MS Stepper Motor MBC12101 Stepper Driver PSA80V4A-1 Power Supply CBL-18AWG-04C-010-MS Motor Cable WIR-1007-18-YEL Power Wire WIR-1007-18-BLK Power Wire
FEATURES SPECIFICATIONS/DIMENSIONS 910 East Orangefair Ln. Anaheim, CA 92801 Tel. (714) 992-6990 Fax. (714) 992-0471 www.anaheimautomation.com The 23Y310S-LW8-MS High Torque Stepper Motor offers a great value without sacrificing quality. This motor was designed to offer the highest possible torque while minimizing vibration and audible noise. It is wired in series with a Molex 4 pin Mini-Fit Jr. receptacle. A 10 ft. 4 conductor, 18 AWG cable with mating 4 pin Mini-Fit Jr plug is included in the PKG-233-MBC12-PS-CBL stepper/motor package. 23Y310S-LW8-MS - High Torque Stepper Motor23Y310S-LW8-MS - High Torque Stepper Motor • NEMA 23 Frame Size • Holding Torque - 320 oz-in • 1.8° Step Angle • High Step Accuracy and Resolution • Low Vibration and Noise • CE Certified RoHS Compliant Model #NEMA Size Holding Torque(oz-in) Bipolar Current (A) Bipolar Resistance (ohms) Bipolar Voltage (v) Bipolar Inductance (mH) Rotor Inertia (oz-in-sec2) Shaft Diameter (in) Weight (lbs) Length (in) 23Y310S-LW8-MS 23320 3.53 5.05.0 6.40 3.2000 .253.204.528 Step Angle Accuracy: ± 5% (Full Step, No Load) Insulation Resistance:100M Ohm Min, 500VDC Resistance Accuracy: ± 10% Dielectric Strength:500VDC for 1 minute Inductance Accuracy: ± 20% Shaft Radial Play:0.02” Max (1.0 lbs) Temperature Rise: 80°C Max (2 Phases On) End Play:0.08” Max (1.0 lbs) Ambient Temperature: -20° to +50° C Max Radial Force:16.9 lbs Insulation Type: Class B Max Axial Force:3.4 lbs-Force Pin #Lead Wire Connection Lead Wire Color 1 2 3 4 Phase 1 (A) Phase 3 (A\) Phase 2 (B) Phase 4 (B\) Soldered Together Soldered Together Black Orange Red Yellow White/Black & White/Orange White/Red & White/Yellow
FEATURES DESCRIPTION 910 East Orangefair Ln. Anaheim, CA 92801 Tel. (714) 992-6990 Fax. (714) 992-0471 www.anaheimautomation.com If you’re looking for high performance in a small driver, the MBC12101 is your answer. This powerful microstepping driver provides excellent torque in a compact and low profile encloser . The MBC12101 is also very easy to use. It features rugged terminal blocks, a rotary pot for current settings, and a visible silkscreen for easy installation. The MBC12101 features optically isolated inputs that are 3.5 - 8.6VDC compatible. The clock input can be set to receive either sinking or sourcing clock signals at frequencies up to 100KHz. The driver also features direction control, motor on/off capabilities, and a built in short circuit and miswire shutdown protection. The MBC12101 is a bipolar type driver designed for use with 4, 6, or 8 lead stepper motors, making it compatible for series and parallel installations. The driver has a 2000 steps per revolution or 0.18° per step resolution,with respect to a 1.8° stepper motor. It also has a motor current reduction feature that will help keep stepper motors cool at standstill, and LEDs that indicate power and pulses being received. MBC12101 - Microstep Driver MBC12101 - Microstep Driver • Compact Stepper Motor Driver • 1.5 - 10.0 Amp Current Range • 2000 Steps per Revolution • Optically Isolated Inputs • Short Circuit Protection • 20 - 80VDC Bus Voltage • Automatic Current Reduction • Sinking and Sourcing Inputs • Power and Clock LEDs • CE Certified and RoHS Compliant Power Requirements: 20 - 80 VDC Output Current Range: 1.5 - 10.0 Amps (Peak) Microstepping Resolution: 2000 Steps/Revolution (Div-by-10) Input Signal Voltage: 3.5 - 8.6 VDC Input Clock Frequency: 0 - 100 kHz Minimum Input Current: (Isolated Inputs) 1.0 mA Storage Temperature: 0° - 50° C Absolute Maximum Driver Temperature: 70° C SOURCING OUTPUTS: SINKING INPUTS: SPECIFICATIONS TYPICAL APPLICATION HOOK-UP
910 East Orangefair Ln. Anaheim, CA 92801 Tel. (714) 992-6990 Fax. (714) 992-0471 www.anaheimautomation.com Optically Isolated Input Pin Descriptions The inputs of the MBC12101 are optically isolated with the anode (+) and cathode (-) both brought out to the user. With no current going through the opto-diode the input is considered high. To enable the input a minimum of 1.0 mA needs to be sourced or sinked through the opto-diode. This is done simply by placing a voltage of +3.5 to +8.6 VDC across the two inputs of the opto-diode. If sourcing current into the inputs, then all three cathodes (-) should be tied together and grounded. If sinking current, then all three anodes (+) should be tied together to the +voltage as shown in theTYPICAL APPLICATION HOOK-UP. To enable an input, apply a DC voltage source of +5VDC to +8.6VDC across the inputs. The Anodes (+) are pins 7, 9, and 11 and the Cathodes (-) are pins 8, 10, and 12. Pin #Description 1 0VDC: Return path for driver voltage 2 20-80 VDC: Input voltage for the driver (+20-80VDC) 3 A: Phase 1 of the Step Motor 4 A\: Phase 3 of the Step Motor 5 B: Phase 2 of the Step Motor 6 B\: Phase 4 of the Step Motor 7 ON/OFF+: On/Off Anode (+) - This isolated input is used to enable and disable the output section of the driver. When HIGH (open) the outputs are enabled. However, this input does not inhibit the step clock. 8 ON/OFF-: On/Off Cathode (-) 9 Dir+: Direction Anode (+) - This isolated input is used to change the direction of the motor. Physical direction also depends on the connection of the motor windings. 10 DIR-: Direction Cathode (-) 11 CLOCK+: Step Clock Input Anode (+) - A positive going edge on this isolated input advances the motor one increment. The size of the increment is dependent on the Microstep Select Inputs of Switch 1. 12 CLOCK-: Step Clock Input Cathode (-) 12 Pin Terminal Block Description Connecting the Step Motor Phase 1 and 3 of the Step Motor is connected between pins 3 and 4 on the terminal block connector. Phase 2 and 4 of the Step Motor is connected between pins 5 and 6 on the terminal block connector . NOTE: The physical direction of the motor with respect to the direction input will depend on the connection of the motor windings. To reverse the direction of the motor with respect to the direction input, swap the wires on Phase 1 and Phase 3. WARNING: Do not connect or disconnect motor wires while power is applied! This driver does not protect itself if the motor is disconnected while powered.
910 East Orangefair Ln. Anaheim, CA 92801 Tel. (714) 992-6990 Fax. (714) 992-0471 www.anaheimautomation.com Reducing Output Current Reducing the output current occurs approximately 1 second after the last positive going edge of the step clock input. The amount of current per phase in the reduction mode is approximately 50% of the set current. Reducing the output current is accomplished when no current flows through the opto-diode at the CLOCK (+) and CLOCK (-) pins after the last step has occurred. The clock LED should be off at this time. The output current on the MBC12101 is set by an onboard potentiometer. This potentiometer determines the per phase peak output current of the driver. Peak CurrentPotentiometer Setting Peak CurrentPotentiometer Setting 1.5A 0%7.0A 60% 2.3A 10%7.9A70% 3.1A 20%8.7A80% 4.0A 30%9.6A90% 5.0A 40% 10A100% 6.0A 50% ---- Setting the Output Current: ItemMinTy pMax Units Input Voltage (Power) 208080 VDC Phase Output Current 1.1---7.1 A (RMS) Phase Output Current 1.5---10.0 A (PEAK) Input Voltage (Inputs) 3.5---8.6 VDC Clock Frequency 0---100 kHz Chopping Frequency 273033 kHz Operation Temperature 0---70 C Absolute Maximum Ratings Input Voltage: 80 VDC Output Current: 10.0 AMPS PEAK Max Plate Temperature: 70° C Storage Temperature: 0° to +50° C The specified motor current of 3.5A for the 23Y310S-LW8-MS (which is the bipolar value) is multiplied by a factor of 1.4 to determine the current adjustment potentiometer value of 5.0Amps o\ r 40%. WARNING: Do not set the current setting above the step motors rated current. When using a higher current setting into a motor, the motor will overheat and burn up. Should this occur, the driver will also be damaged.
PSA80V4A-1 - Power Supply • Low Cost, High Reliability • High Efficiency, Low Working Temperature • Built in EMI Filter, Low Ripple Noise • 100% Full Load Burn-In Test • Short Circuit/Over Voltage/Overload Protection • Compact Size • Light Weight The PSA80V4A-1 unregulated power supply has a single 80V output, a voltage input of 115 or 220VAC, and power capabilities of up to 320 watts. With an unregulated output and a size of 8.30” x 4.25” x 2.81” and dual mounting position “L Bracket,” the PSA80V4A-1 can be mounted just about anywhere. The PKG-233-MBC12-PS-CBl includes two wires for powering the MBC12101. FEATURES DESCRIPTION DIMENSIONS/SPECIFICATIONS 910 East Orangefair Ln. Anaheim, CA 92801 Tel. (714) 992-6990 Fax. (714) 992-0471 www.anaheimautomation.com DC Voltage Output: 80V Output Rated Current: 4A Input Voltage Range: 115/220VAC, 60 Hz Rated Output Power: 320W PSA80V4A-1 - Power Supply