Anaheim Brushless DC BLDPN30001 Spec Sheet

							FEATURES
DESCRIPTION
910 East Orangefair Ln.  Anaheim, CA 92801     Tel. (714) 992-6990     Fax. (714) 992-0471     www.anaheimautomation.com
DIMENSIONS
The BLDPN30001 driver is designed to 
drive DC brushless motors at currents 
of up to 30A (peak) and 50V.  Using hall 
sensor feedback, a constant velocity 
mode can be selected.  The driver is 
protected against over current (cycle-by-
cycle or latched), hall sensor error and 
under voltage.  When an error occurs, a 
fault light and a fault output are turned 
on to notify the user.  Included on the 
driver is an internal potentiometer to 
control the maximum phase current 
allowed into the motor and an internal 
potentiometer to control the speed of the 
motor.  An external voltage (0-5VDC) 
can be used to control the speed as well.
L010584
BLDPN30001 - Brushless DC DriverBLDPN30001 - Brushless DC Driver
• Maximum Current Limit Setting from 10.0- 
  30.0 Amps (Peak)
• Internal or External Potentiometer Speed Control
• 0V to 5V External Voltage Speed Control
• 2-Quadrant Operation
• Hall Sensor Feedback
• Constant Velocity Mode
• Short Circuit Protection
• Requires 90 - 265 VAC Input Power
• Run/Stop, Freewheel and Direction Inputs
• TTL-CMOS Compatible Inputs
• Detachable, Screw Type Terminal Blocks
• RoHS Compliant
the direction of the motor can be preset 
by the direction control input.  Pther 
inputs to the drive include a run/stop and 
motor freewheel input.  When using the 
run/stop input, there are three ramp up 
profi les from standstill to select from.  
The run/stop input overrides all other 
inputs into the driver.Ideal Applications
Automated machinery or processes 
that involve food, cosmetic, or medical 
packaging, labeling, or tamper-evident 
requirements, cut-to-length applications, 
electronic assembly, robotics, factory au-
tomation, special fi lming and projection 
effects, medical diagnostics, inspection 
and security devices, conveyor and ma-
terial handling systems, metal fabrication 
(CNC machinery), pump fl ow control, XY 
and rotary tables, equipment upgrades 
or wherever precise positioning or speed 
control is required. 
						

							SPECIFICATIONS
910 East Orangefair Ln.  Anaheim, CA 92801     Tel. (714) 992-6990     Fax. (714) 992-0471     www.anaheimautomation.com
Control Inputs:
(TB3, Pins 2-4)TTL-CMOS compatible
Logic “0” = 0 - 0.8VDC
Logic “1” = Open
Direction Control:
(TB3, Pin 2)Logic “1” (open) - Clockwise
Logic “0” - Counterclockwise
Freewheel:
(TB3, Pin 3)Logic “1” (open) - Motor is Enabled
Logic “0” - Motor is de-energized and coast
Run/Stop:
(TB3, Pin 4)Logic “1” (open) - Motor will not run and if 
running will decelerate according to ramp 
dip switch setting
Logic “0” - Motor will run and will accelerate 
to ramp dip switch setting
V Control:
(TB3, Pin 6)To control the speed of the motor with and 
external DC voltage, INT/EXT SPD switch 
(SW1-POS1) must be switched to the ON 
position.
0VDC (min) - 5VDC (max)
Control Outputs:
(TB3, Pin 1)TTL-CMOS Compatible
These outputs are able to sink 50mA.
Speed Output:
(TB3, Pin 1)A 5V signal pulse out is available at a rate 
of 4 pulses for 1 revolution of an 8-pole 
motor, 3 pulses for 1 revolution of a 6-pole 
motor, and 2 pulses for 1 revolution of a 
4-pole motor.
8-pole motor RPM = 15 * PG OUT in Hz
6-pole motor RPM = 20 * PG OUT in Hz
4-pole motor RPM = 30 * PG OUT in Hz
Fault Output:
(TB3, Pin 5)Logic “1” (5V Out) - Status good, normal 
operation.
Logic “0” - One of the three fault conditions 
listed in the ‘Fault Protect’ section has oc-
curred.
When a fault is detected, the Fault Output 
(P in 5) goes low.
 WIRING DIAGRAM