American Audio Rack Color LED User Manual

							Descriptions:Congratulations with your purchase of this product.
Read this manual carefully before using our American Audio Rack Color LED. The  is a 19/1U RGB LED Bar
with rainbow effect, providing 24 in color RGB LEDs, designed for the Working DJ. All parameters and work modes can be set up by LED remote operation.Rack Color LEDCheck for transport damage. 
You should be in possession of the following items:1 1 Manual1 LED Remote Control(Infrared Remote Control)Rack Color LEDDelivery Packet:Rack Color LEDMain Features:Should you discover transport damage after unpacking the equipment, inform the hauler immediately. 
Never connect a damaged device. You may also contact your supplier.
User Instructions- Easy-to-use 19 LED bar used to light up your DJ rack(24 LEDs)
-LED Advantages: NO heat output, low power draw, long life LED operation
-3-pin XLR IN/OUT-Master/Slave operation-RC-1 infrared remote control included-Control: color range, brightness & rainbow effect with pattern, speed and fadetime control-LED Colors: Red, Cyan, Green, Magenta, Blue, Yellow, White & Amber
-Power Supply:DC12V, 500mA min included
-Dimensions(LxWxH): 3x19x2/76x482x50mm- 1 rack spaceWeight: 1.5lbs/ 0.8kgCustomer Support:American Audio provides a toll free customer support line, to provide set up help and to answer any question should you encounter 
problems during you set up or initial operation. You may also visit us on the web at www.AmericanAudio.us for any comments or 
suggestions.Voice:(800) 322-6337
Fax:(323) 582-2610E-mail:[email protected] Hours are Monday through Friday 9:00 a.m. To 5:30 p.m. Pacific Standard Time.American Audio - www.AmericanAudio.us 
LOS ANDELES,CA.90058*Please Note: 
Improvements and specifications in the design of the unit and the manual are subject to change without any prior written notice.
*Special Note: 
For reducing signal errors and avoiding signal transmission problems and interference, it is always advisable to connect 120 ohm impedance DMX signal cable and DMX terminator  for signal connection.Notice Information:P/N:24-004-2108-00Rev1.1-Page 1- 
						

							All work modes and parameters can be set up by a combination with Infrared remote control operation.1. Before operation, make sure the batteries(3V, CR2025) have been installed properly.
2. Operation Instructions   There are 8 dedicated color brightness pushbuttons(marked Red, Green, Blue, White,    Cyan, Magenta, Yellow,  Amber). There are also the AUTO and the UNIT SETTING 
   pushbuttons, as well as Raise&Lower keys(marked     for raise and     for lower)    on the remote unit.For further information, please refer to the following table;-Page 2-Operating Instructions:Remote Control2. In Master-Slave operation, one unit will act as the Master unit and the 
    others will act as the Slave units after Daisy chain your units via the     XLR connector.
3. The Brightness is 100%.The Red effect is controlled by Ch1, 
The Green effect is controlled by Ch2, 
The Blue effect is controlled by Ch3.  Pushbuttons&KeysFunctionsRED pushbuttonGREEN pushbuttonBLUE pushbuttonCYAN pushbuttonMAGENTA pushbuttonYELLOW pushbuttonWHITE pushbuttonAMBER pushbuttonAUTO pushbuttonUNIT SETTING pushbuttonPATTERN/RED keyPATTERN/RED keySPEED/GREEN keySPEED/GREEN keyFADE/BLUE keyFADE/BLUE keyBRIGHTNESS keyBRIGHTNESS keyRed, 100% brightnessGreen, 100% brightnessBlue, 100% brightnessCyan, 100% brightnessMagenta, 100% brightnessYellow, 100% brightnessWhite, 100% brightnessAmber, 100% brightnessThe color is changing automatically, and the brightness is 100%.1. DMX address is set 1 by default, and with 24 DMX Channels in total.To select the next pattern or increase the red brightness, and holding it down, 
the brightness will increase continuously until up to the maximum.To select the previous pattern or decrease the red brightness, and holding it down, 
the brightness will increase continuously until up to the minimum.To increase the speed or the green brightness, and holding it down, it will 
increase continuously until up to the maximum.To decrease the speed or the green brightness, and holding it down, it will 
increase continuously until up to the minimum.To increase the fade time or the blue brightness, and holding it down, it will 
increase continuously until up to the maximum.To decrease the fade time or the blue brightness, and holding it down, it will 
decrease continuously until up to the minimum.To increase the overall brightness, and holding it down, it will increase 
continuously until up to the maximum.To decrease the overall brightness, and holding it down, it will increase 
continuously until up to the minimum. 
						

							-Page 3-NOTE:
1.The built-in patterns consists of 1~10 patterns plus a sequence of 10 patterns.
2.There are optional 10 different levels for chase speed;SpeedTime101S92S84S78S616S5432132.5S65S130S260S512S3.And fade time is available from 0% through 100%, total 11levels, 10% per level.4.Effective distance from your unit to Remote Control shall be limited within the range of 10m. Otherwise, it results out of control.AC AdaptorRC-1(Infrared remote control)Physical Dimensions:Milk frost diffuserHousingFace ViewSide ViewTop ViewAccessories(included):