American Audio Digital Producer VMS2 User Manual

							©American Audio®   -   www.americanaudio.us   -   VMS2™ Instruction Manual Page 21
 COMPUTEr CONNECTION
1.  CONNECTINg  ThE VMS2 TO yOUr PC
Connect the VMS2 to your PC by using the USB ports located on the rear of the VMS2 and your PC. Connect 
the supplied USB cable to the USB port on the rear of the VMS2, and the other end connects to the USB port 
on  your  computer. NOTE:  Before  connecting  your  vMS2  to  your  computer  or  laptop,  we  highly  recom-
mend that you install the provided software. The  virtual DJ version included with this product  is specifi-
cally tailored to work with the  vMS2 with no setup required. The setup of other non-factory authorized 
drivers and software is far more complex and in some instances not as reliable.
Speaker Cables
American Audio V4000™ 
						

							©American Audio®   -   www.americanaudio.us   -   VMS2™ Instruction Manual Page 22
SET UP 
						

							©American Audio®   -   www.americanaudio.us   -   VMS2™ Instruction Manual Page 23
Due to fog residue, smoke, and dust, cleaning the mixer should be carried out periodically to residue 
build up.  
1.   Use normal glass cleaner and a soft cloth to wipe down the outside casing.
2.   Use a cleaner specially designed for electronics to spray in and around the knobs and switch.    
  This will reduce small particle built up that can effect the proper operation of the mixer. 
3.   Cleaning should be carried out every 30-60 days to prevent heavy built up.
4.  Always be sure to dry all parts completely before plugging the mixer in.
Cleaning frequency depends on the environment in which the mixer operates (i.e. smoke, fog residue, 
dust, dew).
The crossfader is “Hot Swapable” which means it may be replaced at any time, even when power is 
applied. Replace with American Audio VMS2 crossfader (part# Z-FF-8). If you wish to upgrade to an 
Innofader, please order the Innofader model which comes with the VMS2 plade cover to protect the 
Innofader from damage during handling of the VMS2. If you upgrade to the Innofader, please make 
sure the power is off before upgrading to limit the chance of damage to the Innofader and/or VMS2 
during installation. Replacing with any other model fader may seriously damage your mixer.
Replacing the Crossfader:
1.  Disconnect the mixers main power supply
2.  Using a Phillips screw driver, unscrew the two outside screws on each side that hold the cross   
 fader assembly in place.
3.  Gently remove the crossfader assembly from its seated position. You may need to wiggle the    
 crossfader slightly to remove it.
4.  After removing the crossfader assembly, disconnect the ribbon cable that attaches the cross   
 fader to the PC board. Grasp the crossfader by its base and pull the ribbon cable by its con   
 nector not the actual cables. The connector is designed to only fit one way , so don’t worry    
 about the connectors orientation.
5. Unscrew the two inner screws that connect the crossfader to the crossfader plate.
6.  Connect the new crossfader to the ribbon cable and replace in reverse order.
Note: For Innofader installation instructions please visit http://innofader .com/mixers.
php?id=75
CrOSSFADEr rEPLACEMENT
 CLEANINg 
						

							©American Audio®   -   www.americanaudio.us   -   VMS2™ Instruction Manual Page 24
WARRANTY INFORMATION: The VMS2™ carries a ONE year (365 days) limited warranty. This 
warranty  covers  parts  and  labor.  Please fill  out  the  enclosed  warranty  card  to  validate  your  purchase 
and  warranty.  All  returned  service  items  whether  under  warranty  or  not,  must  be  freight  pre-paid  and 
accompany a return authorization (R.A.) number. If the unit is under warranty, you must provide a copy 
of  your  proof  of  purchase  invoice.  Please  contact  American  Audio® customer  support at  (800) 322-
6337 for a R.A. number. All package not displaying a R.A. number on the outside of the package will 
be returned to the shipper.
1-YEAR LIMITED WARRANTY
A.  American Audio® hereby warrants, to the original purchaser, American Audio® products to be free 
of manufacturing defects in material and workmanship for a period of 1 Year (365 days) from the date 
of  purchase.  This  warranty  shall  be  valid  only  if  the  product  is  purchased  within  the  United  States  of 
America, including possessions and territories. It is the owner’s responsibility to establish the date and 
place of purchase by acceptable evidence, at the time service is sought. 
B.    For  warranty  service,  send  the  product  only  to  the  American  Audio®  factory.  All  shipping  charges 
must be pre-paid. If the requested repairs or service (including parts replacement) are within the terms 
of this warranty, American Audio® will pay return shipping charges only to a designated point within the 
United States. If the entire instrument is sent, it must be shipped in its original package. No accessories 
should be shipped with the product. If any accessories are shipped with the product, American Audio® 
shall have no liability whatsoever for loss of or damage to any such accessories, nor for the safe return 
thereof.  
C.  This warranty is void if the serial number has been altered or removed; if the product is modified in 
any  manner  which  American  Audio®  concludes,  after  inspection,  affects  the  reliability  of  the  product; 
if the product has been repaired or serviced by anyone other than the American Audio® factory unless 
prior  written  authorization  was  issued  to  purchaser  by  American  Audio®;  if  the  product  is  damaged 
because not properly maintained as set forth in the instruction manual. 
D.    This  is  not  a  service  contract,  and  this  warranty  does  not  include  maintenance,  cleaning  or  peri-
odic check-up. During the period specified above, American Audio® will replace defective parts at its 
expense,  and  will  absorb  all  expenses  for  warranty  service  and  repair  labor  by  reason  of  defects  in 
material or workmanship. The sole responsibility of American Audio® under this warranty shall be lim-
ited to the repair of the product, or replacement thereof, including parts, at the sole discretion of Ameri-
can Audio®. All products covered by this warranty were manufactured after January 1, 1990, and bear 
identifying marks to that effect. 
E.  American Audio® reserves the right to make changes in design and/or improvements upon its prod-
ucts without any obligation to include these changes in any products theretofore manufactured. 
F.  No warranty, whether expressed or implied, is given or made with respect to any accessory supplied 
with products described above. Except to the extent prohibited by applicable law, all implied warran-
ties made by American Audio® in connection with this product, including warranties of merchantability 
or  fitness,  are  limited  in  duration  to  the  warranty  period  set  forth  above.  And  no  warranties,  whether 
expressed or implied, including warranties of merchantability or fitness, shall apply to this product after 
said period has expired. The consumer’s and or Dealer’s sole remedy shall be such repair or replace-
ment as is expressly provided above; and under no circumstances shall American Audio® be liable for 
any loss or damage, direct or consequential, arising out of the use of, or inability to use, this product.  
G.  This warranty is the only written warranty applicable to American Audio® Products and supersedes 
all prior warranties and written descriptions of warranty terms and conditions heretofore published. 
 wArrANTy 
						

							©American Audio®   -   www.americanaudio.us   -   VMS2™ Instruction Manual Page 25
gENERAL Model: American Audio® vMS2™ - PC Media Controller
Dimensions:  399(L) x 300(W) x 40(H) mm
      15.7"(L) x 12(W) x 1.5"(H)
Installation:                          Place on flat surface or mount in flat case
Weight: 10.9 Lbs. / 4.93 Kgs    
Power supply:  DC 6V
      Single Voltage:
      AC 100V, 50/60Hz (Japan)
      AC 110V, 60Hz (Colombia)
      AC 120V, 60Hz (U.S.A. and Canada)
      AC 127V, 60Hz (Mexico)
      AC 220V, 50Hz (Chile and Argentina)
      AC 220V, 60Hz (Philippines and Korea)
      AC 230V, 50Hz (Europe, New Zealand, South Africa, and Singapore)
      AC 240V, 50Hz (Australia and U.K.) 
Power consumption:  6W   
Environmental conditions:  Operational temperature: 5 to 35˚C (41 to 95˚F)     
      Operational humidity: 25 to 85% RH (no condensation)     
      Storage temperature: -10 to 60˚C (14 to 140˚F)
Accessories: USB 2.0 Cable Switching Adaptor
     ITEM   NORMAL    LIMIT   CONDITION
Output level: Gain Max, EQ Flat -  5V +/-0.5dB   5V +/-1dB
Line & Mixed Out:   5.5V +/-0.5dB   5.5V +/-1dB 1KHz, 0dB
Phones:   2V       1.8V     1KHz, -20dB
Channel Balance: (From 0 to -40db For Mixed Out) - 
Line:   Within 0.5dB    Within 1dB 1KHz, 0dB
Mixed Out:   Within 1dB    Within 3dB 1KHz, 0dB
L/R Separation - 
Line:   97dB      85dB   1KHz, 0dB
Mixed Out:   95dB      85dB   1KHz, 0dB (Max. Out, EQ Flat)
T.H.D. + NOISE - 
Line:   0.025%    0.03%  1KHz, 0dB
Mixed Out:   0.025%    0.03%  1KHz, 0dB (Max. Out, EQ Flat)
Phones:   0.045%    0.05%  1KHz, 0dB (1V Output)
S/N Ratio - 
Line:   97dB      85dB   1KHz, 0dB
Mixed Out:   97dB      85dB   1KHz, 0dB (Max. Out, EQ Flat)
Dynamic Range (Max. Output, EQ Flat) - 
Line:   96dB      85dB   1KHz,-60dB
Mixed Out:   94dB      85dB   1KHz,-60dB
Frequency Response -
Line:   10-20KHz +/-0.3dB 10-20KHz +/-1dB 
Mixed Out:  10-20KHz +/-0.3dB 10-20KHz +/-1dB
Phones Max. Output:  2V      1.8V   1KHz, 0dB, THD=1%  
NOTES: Specifications and improvements in the design of this unit and this manual are subject to 
change without any prior written notice.
CHECk THE AMERICAN AUDIO WEBSITE FOR DOWNLOADABLE USER SOFTWARE 
UPDATES.
 SPECIFICATIONS 
						

							©American Audio® World Headquarters:
6122 S. Eastern Ave., Los Angeles, CA 90040 USA
Tel: 323-582-3322  Fax: 323-582-3311
Web: www.americanaudio.us  E-mail: [email protected]
American DJ Europe
Junostraat 2
6468 EW Kerkrade
Netherlands
[email protected] / www.americandj.eu
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99