Alpha Tool.Com.HK Limited Polisher VSP320 ver 1 User Manual

Model No.:  VSP-320
Alpha® Variable
Speed Wet Polisher Instruction Manual
MANUAL
WARNING: To reduce the risk of injury, user must read and understand instruction manual!
103 Bauer Drive, Oakland, NJ 07436 • 800-648-7229 • Fax: 800-286-01 14
www.alpha-tools.com
Version 1  

i
Introduction ........................................................................\
.................................. 2
  About Symbols  ........................................................................\
................. 2
General Safety Rules   ........................................................................\
................. 3
  Electrical Safety ........................................................................\
............... 4
  Tool Use and Care...

2
INTRODUCTION
Thank you for purchasing the Alpha® Variable Speed Wet Polisher.  Please read this 
instruction manual thoroughly to ensure safety and correct use of the polisher.  Keep 
this manual in a place where operators can access it easily whenever necessary . 
 ABOUT THE SYMBOLS
According  to  the  hazard  level,  all  safety  notes  in  this  manual  are  classified  into 
“DANGER”, “WARNING”, and “CAUTION”.
 DANGER!    Death or serious personal injury is imminent when handling this 
polisher...

3
  CAUTION
The  following  are  important  notes  for  products,  operation,  and  maintenance 
applicable to this polisher.
GENERAL SAFETY RULES
1. KNOW YOUR POWER TOOL.  Read  owner’s  manual  carefully.  Learn  its 
applications and limitations as well as specific potential hazards particular to 
this tool.
2.  KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.
3.  AVOID DANGEROUS ENVIRONMENTS. Keep work areas as dry as possible. 
Do not use tool in presence of flammable liquids or...

4
10. DON’T ABUSE WATER SUPPLY HOSE. Don’t carry tool by supply hose or 
expose to traffic areas where it can be crushed.
11.  ALWAYS SECURE WORK PIECE. Use clamps or a vise to hold work. It’s safer 
than using your hand and it frees both hands to operate tool.
12.  DON’T OVERREACH. Keep proper footing and balance at all times.
13.  DISCONNECT TOOLS WHEN NOT IN USE. Always  disconnect  tool  before 
servicing when changing blades.
14.  REMOVE ADJUSTING KEYS AND WRENCHES. Form a habit of checking to 
see...

5
•	Do not abuse the cord. Never use the cord to carry the tools or pull the plug 
from  an  outlet/receptacle.  Keep  cord  away  from  heat,  oil,  sharp  edges,  or 
moving parts. Replace damaged cords immediately.  Damaged cords increase 
the risk of electric shock or fire.
•	 When operating a power tool outside, use an outdoor extension cord 
marked “W-A” or “W”.  These  cords  are  rated  for  outdoor  use  and  reduce 
the risk of electric shock. 
TOOL USE AND CARE
•	Use clamps or other practical...

6
SERVICE
• Tool service must be performed only by qualified repair personnel. Service or 
maintenance performed by unqualified personnel could result in a risk of injury.
•  When servicing a tool, use only identical replacement parts.  Follow instructions 
in the Maintenance section of this manual.  Use of unauthorized parts or failure 
to follow maintenance instructions may create a risk of electric shock or injury.
SPECIFIC SAFETY RULES
1. Accessories must be rated for at least the speed recommended on...

7
13.  
Keep hands away from polishing area. Follow this rule will reduce the risk 
of cuts, scrapes, or serious personal injury.
14.    Ground Fault Circuit Interrupter (GFCI) protection should be provided 
on the circuit or outlet to be used for the tool.   Receptacles are available 
having built-in GFCI protection and may be used for this measure of safety .
15.    Save these instruction.   Refer  to  them  frequently  and  use  them  to  instruct 
others who may use this tool.  If you loan someone...

8
1.  
Check the working voltage.   Be sure the voltage available at power outlet 
matches specified voltage on the name- plate. If the polisher is used with 
higher voltage than specified, the motor will burnout. Any attempts to do so 
may damage the polisher or cause an accident or injury.
2.  Inspect all polishing discs.  Never use cracked, chipped or damaged 
polishing discs.
3.  Hold the polisher tightly at start-up.  Failure to do so may cause an injury 
due to high impact at initial start up.
4....

9
VSP-320 OVERVIEW
Ventilation Cap
 SPECIFICATIONS:
Working Power Supply.............................Single-phase AC, 50/60Hz
Voltage  ........................................................................\
............... 120V 
Plug Type ........................................................................\
.....  A (120V)
Amperage  ........................................................................\
.............. 7A
Wattage...