Alpha Tool.Com.HK Limited Polisher VSP230 User Manual

Model No.:  VSP-230
Alpha
®
 Variable 
Speed Wet Polisher
Instruction Manual
MANUAL
103 Bauer Drive, Oakland, NJ 07436 • 800-648-7229 • Fax: 800-286-0114
www.alpha-tools.com
WARNING:  To reduce the risk of injury, user must read and understand instruction manual! 

2
TABLE OF CONTENTS
VSP-230 Overview ............................................................................................ 3
 Specifi cations ............................................................................................. 3
 Accessories ................................................................................................ 4
Introduction ........................................................................................................ 5
  About the Symbols...

3
 VSP-230 OVERVIEW
Speed Adjuster
Power Switch
In-line GFCI
Garden Hose AdapterWater Line Center Water Feed “C” Handle
Water Valve
  SPECIFICATIONS
Working Power Supply ................................................... Single-phase AC, 50/60 Hz
Voltage ........................................................................... 230V
Plug Type ....................................................................... C (230V) 
Amperage ..........................................................................

4
 ACCESSORIES
COMPONENTS:
1. Side Handle (Part No. 210074)
2. Wrench (Part No. 210073)
3. Band Clamp (Part No. 210088)
4. Splash Guard (Part No. 210089)
5.   Spare Set of Carbon Brushes (Part No. 210083)




Figure-2 

5
INTRODUCTION
Thank you for purchasing the Alpha® Wet Polisher.  Please read this instruction manual 
thoroughly to ensure safety and correct use of the polisher.  Keep this manual in a place 
where operators can access it easily whenever necessary.
 ABOUT THE SYMBOLS
According to the hazard level, all safety notes in this manual are classifi ed into “DANGER”,  
“WARNING”, and “CAUTION”.
  DANGER!  Death or serious personal injury is imminent when handling this 
polisher incorrectly.
  WARNING!  There is...

6
  CAUTION!
The following are important notes for products, operation, and maintenance applicable to 
this polisher.
GENERAL SAFETY RULES
 WORK AREA
Keep your work area clean and well lit.  Cluttered benches and dark areas invite 
accidents.
Do not operate power tools in explosive atmospheres, such as in the presence 
of fl ammable liquids, gases, or dust.  Power tools may create sparks which may 
ignite the dust or fumes.
Keep bystanders, children, and visitors away while operating a power tool....

7
Remove adjusting keys or wrenches before turning the tool on.   A wrench or a 
key that is left attached to a rotating part of the tool may result in personal injury.
Do not overreach.  Keep proper footing and balance at all times.  Proper footing and 
balance enables better control of the tool in unexpected situations.  Do not use on a 
ladder or unstable support.
Use safety equipment.   Always wear eye protection.  Dust mask, nonskid safety 
shoes, hard hat, or hearing protection must be used for...

8
 SPECIFIC SAFETY RULES
Accessories must be rated for at least the speed recommended on the tool 
warning label.  Wheels and other accessories running over rated speed can fl y apart 
and cause injury.
Hold tool by insulated gripping surfaces when performing an operation where 
the cutting tool may contact hidden wiring or its own cord.  Contact with a “live” 
wire will make exposed metal parts of the tool “live” and shock the operator.
Know your power tool.  Read operator`s manual carefully.  Learn its...

9
  USE PROPER EXTENSION CORDS
Use only three-wire extension cords that have three-prong grounding-type plugs and 
three-pole receptacles that accept the tool’s plug.  Make sure your extension cord is in 
good condition.  Replace or repair damaged or worn cord immediately.  When using an 
extension cord, be sure to use one heavy enough to carry the current your product will 
draw.  An undersized cord will cause a drop in line voltage resulting in loss of power and 
overheating.  Below table shows the...

10
 ADDITIONAL PRECAUTIONS FOR USING THE VSP-230
In addition to the general safety notes described on the preceding pages, please read and 
observe the following precautionary notes before using the polisher.
  DANGER!
1. Check the working voltage.
  Be sure the voltage available at power outlet matches specifi ed voltage on the name-
plate.  If the polisher is used with higher voltage than specifi ed, the motor will burnout.  
Any attempts to do so may damage the polisher or cause an accident or injury....