Alpha Tool.Com.HK Limited Ecoguard Type G ver 3 User Manual

103 Bauer Drive, Oakland, NJ 07436 • 800-648-7229 • Fax: 800-286-0114
www.alpha-tools.com
Part No: ECOGRDGR  Version 3
Alpha® Ecoguard Type G
Dust Collection Cover  Instruction Manual
MANUAL
(*Shown with angle grinder / sold separately)  

2
tablE Of CONtENtS
 
 
Introduction ........................................................................\
............................... 3
 

a bout the Symbols
 
 ........................................................................\
........... 3
Ecoguard 
type G Overview 

........................................................................\
...... 4
 

Contents   ........................................................................\
........................... 4
Ecoguard 
type G Other...

3
INtRODuCtION
thank you for purchasing the alpha® Ecoguard  type G Dust Collection Cover.  t he 
Ecoguard 
type G must be used with a vacuum, 
 or other dust collection system.  
to ensure correct use, 

read this Instruction Manual and the Instruction Manual for 
the power tool and follow the operating instructions.  Keep this manual in a place 
where operators can access it easily whenever necessary!
 abOut thE SyMbOlS
According 

to  the  hazard  level,  all  safety  notes  in  this  manual  are...

4
 CONtENtS:
1. Connectors:  a.
 
Makita®, Milwaukee® & bosch®:  Preset to Ecoguard G
b.
  h
itachi®
c.  b osch® / Metabo®
d. f lex®
e. Dewalt®
2. b ase  f lange
3.  
Inner 
 f lange
4.
  l
ock Nut
5.
 
Spacers 
 ( t 2.5,  t 5.0,  t 7.0,  t 9.4 / mm)
6.
 
Collar (for Metabo®)
7.
 
Stainless Steel 

h
ose  b and
8.
  h
ex. Wrench
9.
 
Rubber 

h
ose Connector
ECOGuaRD tyPE G OVERVIEW
e
(Optional / Sold Separately)   

5
ECOGuaRD tyPE G SPaCERS  a ND   CONNEC tORS
MaKIta®/MIlWauKEE®/bOSCh®hItaChI®
DEWalt®
flEX®
bOSCh® / MEtabO®   

6
INStallING thE DuSt COllECtION COVER
  WaRNING! 
1.
  b
e sure to turn off the high-speed angle grinder and remove the plug from 
the electrical outlet before attaching and installing the Dust Collection Cover.
2.
  t
ake the Guard of

f from the Grinder. 
 
 
 
 
 
3.
 
Make sure the Dust Collection Cover is securely attached, otherwise it m\
ay 
come loose which could cause injury

.
4.
 
If you installed 

the Dust Collection Cover to a high-speed angle grinder but 
the connector is loose and cannot...

7
 INStallING thE CONNECtOR
If a dif
ferent Connector is needed, exchange the connector per the following 
instructions.
1.
 l
oosen the Screws.
2.
 t
ake the front of the Connector a

ssembly off. 
 
3.
 l
oosen the  f lat  h ead Screws using the  h ex Wrench.
4.
 t
ake the back of the Connector a

ssembly off.
5.
 
Replace with other Connector
 .
6.
 
Place in the other Connector a
 ssembly.
7.
 t
ighten 

f lat  h ead Screws with  h ex Wrench.
 (DO NO

t
 forget to insert taper W
 ashers)
(fig.2)
( f...

8
8. tighten the Screws
 

  
     (DO NO

t
 forget to insert Spring W
 ashers)
  CautION!
the Dust Collection Cover is solely designed for use with a grinding cup \
wheel. Do 
not use with any other type of blade, such as a cutof f or tip saw blades.
 INStallING thE flEX® CONNECtOR
NO
t
E:  
t

he 
f
lex
® connector is connected directly to the Grinder, as shown in 
f

igure 5.
Screw
M4x10
flex® Connector
(fig.4)
(
f
ig.5)   

9
MOuNtING thE GRINDING CuP W h EE l tO  th E   GRINDER
  WaRNING!
Make sure the Ecoguard type G is securely  atttached to the grinder, otherwise it 
may come loose, causing injury.
1.
  f
irmly hold Connector 
a
 ssembly and 
tighten the screws.
2.
 
Set the proper Spacer into the spindle.
3.

 
Set the 
 b ase or Inner  f lange on the 
Spacer.
4.
 
Set the G
 rinding Cup Wheel 
on the 
b ase or Inner  f lange.
5.
 
Set the 
 l ock Nut on the 
Grinding Cup Wheel.
 
(be 
c

areful to ensure the correct...

10
ATTACHABLE GRINDERS FOR ECOGUARD G
BRAND
h
I ta C h I
®
DEW
al
t
®
flEX®
MIlWau
KEE
®
MaKIta®
bOSC
h®
ME
tab
O®
PART NO. 500070 500073 500071 500002500027
CONNECTORS        (
f actory Preset)
COLLAR N/
a
G12S

a 3
G12E2
G12SE2P9 G12V
a
G12SV
a
G12SR3G12SS
G13SC2
G13SC2P9 G13SPG13V
a
DWE401

1
DWE4120(N) D28110
D28112
D28402
D28065 D28114
D28115
D28131
D28140
D28144
l

3410VRG 61306140
6146
6147
61216117
6121
6124
6161 G
a 4030(K)
G
a 4530
G
a 4534
G
a 5010Z
G
a 5020( y )
9554N
b
9557N

b /P b
9558P...