Home
>
Alpha Tool.Com.HK Limited
>
Ecoguard
>
Alpha Tool.Com.HK Limited Ecoguard Type G ver 2 User Manual
Alpha Tool.Com.HK Limited Ecoguard Type G ver 2 User Manual
Here you can view all the pages of manual Alpha Tool.Com.HK Limited Ecoguard Type G ver 2 User Manual. The Alpha Tool.Com.HK Limited manuals for Ecoguard are available online for free. You can easily download all the documents as PDF.
Page 1
103 Bauer Drive, Oakland, NJ 07436 • 800-648-7229 • Fax: 800-286-0114 www.alpha-tools.com Part No: ECOGRDGR Version 2 Alpha® Ecoguard Type G Dust Collection Cover Instruction Manual MANUAL (*Shown with angle grinder / sold separately)
Page 2
2 tablE Of CONtENtS Introduction ........................................................................\ ......... 3 About the Symbols ............................................................... 3 Ecoguard Type G Overview ........................................................ 4 Accessories ........................................................................\ . 4 Installing the Dust Collection Cover ............................................5 Installing the Connector...
Page 3
3 iNtRODuCtiON thank you for purchasing the alpha® Ecoguard type G Dust Collection Cover. the Ecoguard type G must be used with a vacuum, or other dust collection system. t o ensure correct use, read this instruction Manual and the instruction Manual for the power tool and follow the operating instructions. Keep this manual in a place where operators can access it easily whenever necessary! abOut thE SyMbOlS According to the hazard level, all safety notes in this manual are...
Page 4
4 Stainless Steel hose band Rubber hose adapter ECOGuaRD tyPE G OVERViEW aCCESSORiES Ecoguard Dust Collection Cover w/ Connector (Part# 500028) .....1 pc Collar ........................................................................\ ..................... 2 pcs additional Connector assembly for Most 5” Grinders ....................2 pcs flanges and lock nut Set for Selected Grinders ................1 Set (3pcs) hex Wrench...
Page 5
5 iNStalliNG thE DuSt COllECtiON COVER WaRN iNG! 1. be sure to turn off the high-speed angle grinder and remove the plug from the electrical outlet before attaching and installing the Dust Collection Cover. 2. take the Guard off from the Grinder 2. Make sure the Dust Collection Cover is securely attached, otherwise it may come loose which could cause injury. 3. if you installed the Dust Collection Cover to a high-speed angle grinder but the connector is loose and cannot be securely...
Page 6
6 if the different Connector is needed, exchange the connector as per the following \ instructions.1. loosen the Screws. 2. take the front of the Connector assembly off. 3. loosen the flat head Screws using the hex Wrench. 4. take the back of the Connector assembly off. 5. Replace with other Connector. 6. Place in the other Connector assembly. Ecoguard type G Screw Connector assembly (front) hex-Wrench flat head Screw Connector assembly(back)
Page 7
7 7. tighten flat head Screws with hex Wrench. (DO NOt forget to insert taper Washers) hex-Wrench flat head Screw 8. tighten the Screws (DO NOt forget to insert Spring Washers) CautiON! the Dust Collection Cover is solely designed for use with a grinding cup wheel. Do not use with any other type of blade, such as a cutoff or tip saw blades. taper Washer Screw M4x10
Page 8
8 MOuNtiNG thE GRiNDiNG CuP WhEEl tO thE GRiNDER WaRN iNG! Make sure the Ecoguard type G is securely atttached to the grinder, otherwise it may come loose, causing injury . 1. firmly hold Connector assembly and tighten the screws. 2. Set the proper Spacer into the spindle. 3. Set the base or inner flange on the Spacer. 4. Set the Grinding Cup Wheel on the base or inner flange. 5. Set the lock Nut on the Grinding Cup Wheel. (be careful to ensure the correct direction of the lock Nut) 6....
Page 10
10 attaChablE GRiNDERS GRiNDERSiZEMODEl alPha ®5” hSG-125 MaKita 4-1/2” Ga4530 Ga4534 9564CV 9564PC 9557Nb 9557Pb 5” Ga5010Z Ga5020 Ga5020y 9558Pb 9565CV 9565PC 6” Ga6020 Ga6010Z 9566CV 9566PC hitaChi 4-1/2”G12Sa3 G12SE2 G12SE2P9 G12SV a G12SR3 G12SS 5” G13SC2 G13SC2P9 G13SP G13V a GRiNDER SiZEMODEl bOSCh 4-1/2” 1800 1810PS 1810PSD 5” 1801 1803EVS 1811PS 1821 1821D 6” 1806E 1812PSD MEtabO 4-1/2” W8-115 W8-115 Quick W8-115 QuickProtect 5” W8-125 Quick W11-125 Quick Wa11-125 Quick WE9-125 Quick...