Alpha Tool.Com.HK Limited Ecoguard Type C User Manual

Part No: ECOGRDCT Version 3
103 Bauer Drive, Oakland, NJ 07436 • 800-648-7229 • Fax: 800-286-01 14
www.alpha-tools.com
Alpha® Ecoguard Type C  
Dust Collection Cover Instruction Manual
MANUAL
(*Shown with angle grinder / sold separately)  

2
TablE Of CONTENTS
 
Introduction ........................................................................\
......... 3
About the Symbols ..................................................................... 3
Precautions for Using Dust Collection Cover  .............................3
Ecoguard Type C Overview  ........................................................ 4
Accessories  ........................................................................\
........ 5
Ecoguard Type C Spacers and Connectors...

3
INTRODuCTION
Thank you for purchasing the alpha® Ecoguard Type C, a Hybrid Dust 
Collection Cover.  The Ecoguard Type C can be used without a vacuum, or 
other dust collection system.  To ensure correct use, read this Instruction 
Manual and the Instruction Manual for the power tool and follow the oper\
ating 
instructions.  Keep this manual in a place where operators can access it easily 
whenever necessary!
  abOuT THE SyMbOlS
According to the hazard level, all safety notes in this manual are...

4
ECOGuaRD TyPE C OVERVIEW
Connector assembly
Knob bolt
Height adjustment Knob
foot Plate
Dust Collection Cover
Dust bag
base Plate   

5
 aCCESSORIES    

6
ECOGuaRD TyPE C SPaCERS aND CONNECTORS
Reference: The combination of Spacer & flange
alPHa® MaKITa®MIlWauKEE HITaCHI  METabO®bOSCH 
HSG-125 9557 / 9558
9564 / 9565
9566 6117 series
6161 series G12SS / G12SR3
G12SE2 / CM5Sb WE9-125 / WE14-125
W11-125 1800 / 1801
1803 / 1806E 1810~1812
flange 500046 500007
lock Nut Original 500008
Spacer 500047/T4.0 500012/T5.0 500048/T7.2500023/T8.6500047/T4.0
® ®
®   

7
 INSTalla TION Of THE DuST COllECTION COVER
  WaRNING!
1.  be sure to turn off the high-speed angle grinder and remove the plug 
from the electrical outlet before attaching and installing the Dust 
Collection Cover. 
2.  Make sure the Dust Collection Cover is securely attached; otherwise 
it may come loose which could cause injury.
3.  If you installed the Dust Collection Cover to a high-speed angle grinder\
 
but the connector is loose and can not be securely attached, do not 
use the Dust Collection...

8
 INSTallING TO OTHER HIGH-SPEED aNGlE GRINDERS WITH  
INCluDED OTHER CONNECTORS
 If you install the Dust Collection Cover to a high-speed angle grinder \
but 
the connector is loose and cannot be securely attached, it may be necess\
ary 
to change the connector designed for other makes.
1.  Remove the three screws in the connector attached to the Dust 
Collection Cover. (fig. 3)
2.  attach the supplied connector by following the instruction in (1) above\
 
in reverse.  (for Hitachi Grinder use Part No:...

9
3. Mount  the  supplied  spacer  with  the  power  tool  or  dedicated  flange 
lock nut set on the spindle and then mount the diamond wheel. ( fig. 6)
4.  Mount  the  inner  flange  on  the  spindle  on  top  of  the  diamond  wheel 
with the convex side of the inner flange on the diamond wheel side. 
5.  Press the lock pin to fix the spindle and securely tighten the lock nut 
with a pin wrench.
6.  Replace the Dust Collection Cover (fig. 4) and tighten the knob (a).
 aDJuSTING THE CuTTING DEPTH
1....

10
bottom Plate
foot Plate
 OPTION 1 - fREE-HaND CuTTING
Cutting  application using The Supplied Hybrid Dust bag
1.  Securely connect Dust bag to the duct 
(fig.7) making sure that the fastener of 
the Dust bag is securely closed.
2.  Confirm the direction of Cutting and the 
blade rotation.
3.  Turn the Grinder on and start cutting 
application. Dust bag should be emp-
tied with every 3m of cutting.
4.  Ensure there is NO gap between the    
material and Dust Cover, otherwise the 
dust could leak out...