Alpha Tool.Com.HK Limited Beveling Auxiliary Base User Manual

11
INsTAllING GrINder/PolIsher  ACCessorIes
ATTAChING BeVelING BAse To WorKPIeCe
Spindle Lock
Polishing or
 Grinding Tool
1. Push the spindle lock and install 
the grinding or polishing accessory, 
then tighten it using the wrench.
figure-11
figure-12
1. Place the beveling auxiliary base with grinder/
polisher on the edge of the stone slab and 
push the Guide support against the stone 
while the Guide support is secured to the base. 
 
 
 
2.  loosen up the fixing Bolt to make the grind-
ing wheel...

12
3. Turn the Adjustment Knob counterclockwise 
to lower the wheel until the  wheel is lightly 
touching the corner of the stone.
4.  loosen up the fixing Bolt on the Angular 
Measure then set the indicator to point “0”, 
next secure the Angular Measure by tightening 
up the fixing Bolt.
 
 
 
 
 
 
5.  Turn the Adjustment Knob to lower to the 
desired cutting depth (5mm shown in  figure 
15). Next secure the wheel position by tighten -
ing up the fixing Bolt.   It is now ready for the 
grinding...

13
BeVel GrINdING/PolIshING (15- 45°)
 
1.  Attach the Turboshine Grinding Wheel, 60 grit (Part # TsV30060M) to the Universal Adapter. 
When attaching the grinding wheel make sure that the grinding wheel does not make 
contact to the main base of the BAB1590.
2.  Adjust the Beveling Auxiliary Base to the desired angle to be performed.
3.  start grinding the edge of the material by moving the Beveling Auxiliary Base across the 
material in back and forth motions. Make sure that the Guide support keeps in...

14
sTrAIGhT edGe GrINdING (90°) UsING “sTrAIGhT 
edGe GUIde”
1. Attach the Turboshine Grinding Wheel, 60 grit (Part # TsV30060M). When attaching 
the grinding wheel make sure that the grinding wheel does not make conta\
ct to the 
main base of the BAB1590
2.  lay the straight edge guide parallel to the edge of the material.
3.  determine the distance of the straight edge guide from the edge of materi\
al, measure the 
distance from the grinding wheel’s surface to the back of the main base. 
4.  After the...

15
sTrAIGhT edGe PolIshING (90°) UsING A “sTrAIGhT 
edGe GUIde”
1. Attach the Turboshine dual Adapter to the Universal Adapter.
2.  Attach either the #100 grit or #200 grit Turboshine (rigid) to the dual Adapter. operator 
will choose which grit will work best for the application based on operator’s experience.
3.  lay the straight edge guide parallel to the edge of the material.
4.  determine the distance of the straight edge guide from the edge of material, measure the 
distance from the polishing...

16
4. determine the distance of the straight edge guide from the edge of materi\
al, measure 
the distance from the Turboshine wheel’s surface to the back of the main base. 
5.  After the distance of the straight edge guide has been determined, secur\
e it using 
clamps. (See Fig. 18 & 19 on page 14)
6.  Move the Beveling Auxiliary Base across the material in back and forth motions making 
sure that the Main Base keeps in contact with the straight edge guide du\
ring polishing.  
7.  Continue the...

17
AlPhA® BeVelING AUxIlIAry BAse sCheMATIC   

18
AlPhA® BeVelING AUxIlIAry BAse PArTs lIsT
drAWING No. PArT No.desCrIPTIoN QUANTITy
1 150001 Main Base 1
2 150002 rolling Wheel 8
3 150003 screw A01A10101  8
4 150004 handle 1
5 150005 Pin P001 1
6 150006 Gliding Pin 2
7 150007 hex. screw CAP021 7
8 150008 lift Base 1
9 150009 screw A01A30100  1
10 150010hex. screw CAP042 2
11 150011spring s064 1
12 150012Gliding spacer 1
13 150013Guide rail 1
14 150014Washer T10x16x1.5  1
15 150015Angular Measure 1
16 150016fixing Bolt 1
17 150017spring s074 1
18...

19
AlPhA® BeVelING AUxIlIAry BAse PArTs lIsT
drAWING No. PArT No.desCrIPTIoN QUANTITy
37 150038Water hose (3M) 1
38 150039Coupling Assy. 1
39 150040Bearing Nut 1
40 150041Bearing housing 1
41 150042Ball Bearing (B6004llU) 2
42 150043Main shaft (5/8”-11 UNC)
      *other sizes available upon request 1
43 150044Bearing housing Cover 1
44 150045screw MT011  3
45 150046Bracket 1
46 150047hex. screw CAP044 2
47 150048screw with Knob 1
48 150049stopper 1
49 150050hex. Wrench 5mm 1
50 150051spanner Wrench 1
51...

Copyright © 2014 Alpha Professional Tools. All rights reserved. 
103 Bauer Drive, Oakland, NJ 07436 • 800-648-7229 • Fax: 800-286-01 14
www.alpha-tools.com
06/2014