AllTrade Tradespro 5 Gal Air Compressor Reconditioned 835486 User Manual

							ASSEMBLY INSTRUCTIONS
THE COMPRESSOR IS SHIPPED WITHOUT OIL IN THE CRANKCASE. ADD OIL AS INDICATED BELOW.
STEP 1 – PUMP LUBRICATION
This air compressor features an oil lubricated pump that requires the use of SAE 30 weight non-detergent air compressor oil.
Adding Compressor Oil:
1. Place air compressor on a flat, level surface.
2. Remove plastic oil fill 
breather plug (see Fig. 1).
4. See diagram for determining proper oil fill level using oil fill sight glass 
(see Fig. 3).
5. Install supplied plastic oil fill breather plug securely into oil fill hole.
DO NOT OPERATE THE COMPRESSOR WITHOUT LUBRICANT, OR WITH LOW LUBRICATION LEVEL. THE MANUFACTURER IS NOT
RESPONSIBLE FOR DAMAGE CAUSED TO THE COMPRESSOR DUE TO OPERATION WITHOUT PROPER LUBRICATION.
STEP 2 – INSPECTION CHECK
Assembly Check:
In order to complete the assembly of your new air compressor, a careful inspection should be made to ensure that all of the parts are properly
aligned and securely fastened.
1. Inspect air filter to ensure that it is installed and secure.
2. Check oil fill level in crankcase.
9
3. Open supplied oil bottle and pour oil into crankcase until the oil level reaches the center
of the red circle in the oil level sight glass (see Fig. 2). Be careful not to overfill.
Fig. 2Fig. 1
CHECK OIL
LEVEL DAILY!
REFILL OILIMMEDIATELY
OIL LEVEL OK
OIL CAPACITY: 28oz (833ml)
CAUTION
Fig. 3  
						

							OPERATION
INITIAL SETUP / BREAK-IN PROCEDURE:
Do not attach air hose, air tools or other air accessories to the air outlet until break-in procedure has been successfully completed.
1. Read and understand the entire instruction manual, including all safety warnings before setting up air compressor.
2. Place air compressor on a flat, level surface.
3. Check oil fill level in crankcase and add oil as needed.
4. Turn the pressure regulator knob fully clockwise to open airflow from air outlet port. 
Be careful not to overtighten pressure regulator knob when it “bottoms out” as this may damage pressure regulator.
5. Turn the power switch to the OFF position.
6. Plug power cord directly into a properly grounded power source of the correct voltage (see Grounding Instructions on page 5 of this
instruction manual).
7. Open the tank drain valve to allow air to escape preventing air pressure buildup in the air tank.
8. Turn the compressor ON by moving the switch to the AUTO/ON position and run the air compressor for a period of 20 minutes to break-in
the air pump.
9. With the compressor still running, at the end of the 20-minute break-in period, close the tank drain valve. The air compressor will build air
pressure to the maximum preset pressure (“cut-out” pressure) and automatically shut off.
10. Slowly turn the tank drain valve to open airflow from drain and bleed off air from the air tank. The air compressor will automatically restart
once the pressure in the air tank drops below the minimum preset pressure (“cut-in” pressure).
11. Turn the compressor off by moving the switch to the OFF position.
12. Release pressure from the system. Drain moisture from the air tank by slowly opening the air tank drain valve by turning clockwise. 
Tilt tank to remove all moisture. Once all the moisture has drained out, close the fitting securely. 
NOTE:Air tank will not pressurize while drain valve is open.
13. Disconnect the power cord from the power outlet. 
NOTE:Make sure the power switch is in the OFF position when connecting or disconnecting power cord from electrical outlet.
14. Your new air compressor is now ready to use. 
STARTUP:
1.Before each startup, make sure the power switch is in the OFF position.
2.Place air compressor on a flat, level surface.
3.Check oil fill level in crankcase and add oil as needed.
4.Release pressure from the system. Drain moisture from the air tank by slowly opening the air tank drain valve by turning clockwise. Once all
the moisture has drained out, close the fitting securely.NOTE:Air tank will not pressurize while drain valve is open.
5.Turn the pressure regulator knob fully counterclockwise to close airflow from air outlet port.
6. Attach air hose and accessories.
TOO MUCH AIR PRESSURE CAUSES A HAZARDOUS RISK OF BURSTING. CHECK THE MANUFACTURER’S MAXIMUM PRESSURE RATING FOR
AIR TOOLS AND ACCESSORIES. THE REGULATOR OUTLET PRESSURE MUST NEVER EXCEED THE MAXIMUM PRESSURE RATING.
7.Before connecting the compressor to the grounded outlet, check oil level, check for broken components and accessories, and check for
damage to the hose.
8.Plug power cord directly into a properly grounded power source of the correct voltage (see Grounding Instructions on page 5 of this
instruction manual).
9.Turn the compressor ON by moving the switch to the AUTO/ON position and allow the tank pressure to build. Once the air pressure reaches
the maximum preset pressure (“cut-out” pressure) it will automatically shut off.
10.Slowly turn the pressure regulator knob clockwise to open airflow from air outlet port until desired output pressure is reached. NOTE:The
air compressor will automatically restart once the pressure in the air tank drops below the minimum preset pressure (“cut-in” pressure).
MAINTENANCE
DISCONNECT AIR COMPRESSOR FROM POWER SOURCE AND BLEED OFF ALL AIR PRESSURE 
BEFORE ATTEMPTING ANY MAINTENANCE OR REPAIR.
10  
						

							SHUTDOWN AND STORAGE:
NOTE: NEVER stop the air compressor by unplugging it from the power outlet as this may result in damage to the compressor.
1.Turn the switch to the OFF position
2.Disconnect the power cord from the power outlet by grabbing the plug (not the cord). Loop around handle for storage.
3.Turn the pressure regulator knob fully counterclockwise to close airflow from air outlet port. Check the outlet pressure gauge to ensure that
it reads 0 PSI.
4.Remove the air hose and any air accessories.
5.Drain moisture from the air tank by slowly opening the air tank drain valve by turning clockwise. Tilt tank to remove all moisture. Once all
the moisture has drained out, close the fitting securely.
6.Allow the compressor to cool down.
7.Wipe the air compressor clean and store it in a clean, dry, and non-freezing location.
WHEN PERFORMING ANY MAINTENANCE OR SERVICE:
1.The air compressor must be turned off.
2.Disconnect compressor from the power source.
3.Open tank drain to bleed off all air pressure before attempting any maintenance or repair.
4.Allow compressor to fully cool before attempting any maintenance or repair.
Check the air compressor frequently for any visible problems and follow maintenance procedures each time the compressor is used.
All air compressors contain maintenance parts that require periodic replacement. These used parts, including air filters and used lubricating oil,
may contain regulated substances that must be disposed of in accordance with local, state, and federal laws and regulations.
1.Turn compressor off and release pressure from the system. Drain moisture from the air tank by slowly opening the air tank drain valve by
turning clockwise. Tilt tank to remove all moisture. Once all the moisture has drained out, close the fitting securely.
2.Wipe the compressor clean.
MAINTENANCE CHECKLIST:
Daily:
• Check oil level.
• Drain accumulated liquid from tank.
• Check for oil leaks.
• Check for unusual noise and/or vibrations.
• Check that all fasteners are secure.
• Wipe compressor clean.
+Apply a solution of soapy water around joints. Look for air bubbles around joints when compressor reaches the pressure cut-out limit and the
pump turns off.
* The pump oil must be changed after the first 20 hours of operation. Thereafter, change oil every 200 hours of operation or every six months,
whichever comes first. In harsh operating conditions, maintenance must be performed more frequently.
OIL CHANGE:
Used lubricating oil may contain regulated substances that must be disposed of in accordance with local, state, and federal laws and regulations.
1. The air compressor must be turned OFF.
2. Allow compressor to fully cool before attempting any maintenance or repair.
3. Place a suitable oil drain pan below oil drain plug (see Fig. 4).
4. Remove oil fill breather plug to allow air to enter crankcase.
5. Remove oil drain plug.
6. Allow oil to drain completely. Tilt air compressor towards the oil drain to assist draining.
7. Clean and replace oil drain plug.
8. Refill crankcase with SAE 30 weight non-detergent air compressor oil until the oil level
reaches the center of the red circle in the oil level sight glass. Be careful not to overfill.
9. Reinstall the oil fill breather plug.
11
Weekly:
• Inspect and clean air filter.
• Clean breather holes on oil fill plug.
Monthly:
• Check for air leaks.+
• Check safety relief valve.
Six months or 200 operating hours:*
•Change compressor oil. Use only SAE
30 weight non-detergent air
compressor oil.
•Replace oil more frequently when
used in dusty operating environments.
Fig. 4  
						

							CHECKING SAFETY RELIEF VALVE:
SAFETY RELIEF VALVE MUST BE REPLACED IF IT CANNOT BE ACTUATED OR IT LEAKS AIR AFTER THE RING IS RELEASED.
1. The air compressor must be turned OFF.
2.Disconnect compressor from the power source.
3. Open tank drain to bleed off all air pressure before attempting any maintenance or repair.
4. Allow compressor to fully cool before attempting any maintenance or repair.
5.  Grasp the wire ring on the safety relief valve.
6. Pull and release the ring a few times to ensure that the plunger moves in and out. Replace the safety relief valve if plunger does not move or
is difficult to move.
CHECKING AIR FILTER ELEMENT:
1. The air compressor must be turned OFF.
2. Disconnect compressor from the power source.
3. Open tank drain to bleed off all air pressure before attempting any maintenance or repair.
4. Allow compressor to fully cool before attempting any maintenance or repair.
5. Remove the face of the filter body to access the filter element by pushing and rotating the front portion of the filter body in a counter
clockwise direction to release the locking tabs.
6. Use compressed air to blow loose dirt and debris from the paper filter element. Replace filter element if it cannot be cleaned sufficiently.
7. Reinsert filter element into filter body and reinstall filter faceplate.
MOISTURE IN COMPRESSED AIR
Moisture is a normal by-product of compressing air. As the moisture builds during compressor use, it can be carried though the air hose. When
using paint spray gun or sandblasting gun, the use of a special filter to remove moisture from the air line is highly recommended. Moisture in
the compressed air will cause water spots in paint jobs and cause blasting media to clog the sandblasting gun.
12  
						

							13
TROUBLESHOOTING GUIDE
Problem EncounteredPossible CausePossible Solution
The compressor does not start or restart:Power cord not plugged in.Plug cord into grounded outlet.
Motor/Pressure switch in OFF positionMove switch to AUTO position.
Motor thermal overload switch hastripped.Turn air compressor off, wait until the motor is cool, thenpress motor thermal overload (red) button firmly until click is heard.
Fuse blown or circuit breaker hastripped.Replace fuse or reset circuit breaker.
Check for proper fuse amperage.
Check for low voltage conditions.
Disconnect any other electrical appliances from circuit oroperate air compressor on its own branch circuit.
Wrong gauge wire or length ofextension cord.Check chart in instruction manual for proper gauge wire and cord length.
Air tank pressure exceeds motor/pressureswitch cut-in pressure.Motor will start automatically when air tank pressure dropsbelow cut-in pressure of motor/pressure switch.
Pressure release valve onmotor/pressure switch has notunloaded pump head pressure.
Bleed the line by moving the switch to the OFF position.
Defective motor, motor capacitor,motor/pressure switch.Contact Consumer Helpline at 1-800-423-3598.
The compressor motor stalls:Overloaded motor.Have a certified electrician check the motor and wiring.Proceed with his or her recommendations.
Improper lubrication.See LUBRICATION section in instruction manual.
Low oil level.Check oil level and fill if necessary.
Defective check valve.Replace check valve.
Excessively noisy operation:Loose motor pulley or pump flywheel.Tighten pulley and/or flywheel (where applicable).
Lack of oil in the pump crankcase.Check oil level. If low, check for possible bearing damage.Add correct amount of oil.
Carbon deposits on pistons or valves.Remove cylinder head and inspect. Clean or replace parts as needed.
Bearing, piston or connecting rodfailure.STOP THE COMPRESSOR! Contact Consumer Helpline at 1-800-423-3598.
Worn connecting rod.Replace with new connecting rod.
Worn piston wrist pin bushing.Remove piston/connecting rod assembly from the compressorand inspect for excess wear. Replace worn parts as needed.
Worn bearings.Replace worn bearings as needed. NOTE:Dirty oil can cause accelerated wear. Change oil frequently using recommended oil.
Noisy check valve.Replace check valve.
When in the Start/Stopoption, motor runscontinuously:
Motor/Pressure switch does not shutoff motor when air compressorreaches cut-out pressure and safetyrelief valve activates.
Move the motor/pressure switch to the OFF position. If themotor does not shut off, unplug the air compressor. If theelectrical contacts are welded together, replace the pressureswitch.
Air compressor is incorrectly sized.Limit the air pressure to the capacity of the air compressor.Either use a smaller tool or a larger air compressor.
Overheating:Poor ventilationRelocate the air compressor to an area with an ample supplyof cool, dry, and well-circulated air is available.
Dirty cooling fins.Clean the outer surfaces of the cooling fins on the pump andmotor assembly.
Air continues to leak atmotor/pressure switch releasevalve after motor stops:
Defective pilot valve, the check valve isstuck open.Remove, clean or replace.  
						

							14
TROUBLESHOOTING GUIDE
Problem EncounteredPossible CausePossible Solution
Air continues to leak atmotor/pressure switch releasevalve while motor is running:
Defective motor/pressure switch.Replace.
Check valve stuck in open position.Replace check valve. DANGER—Do not disassemble thecheck valve with tank pressurized. Open tank petcock valveto allow air to escape from tank prior to servicing.
Air leaks from safety reliefvalve:Possible defective safety relief valve.Operate safety relief valve manually by pulling on ring. If itstill leaks, it should be replaced.
Excessive tank pressure.Defective motor/pressure switch. Replace.
Air leaks at pump:Blown gaskets.Replace blown gaskets and torque head bolts to 20 ft./lbs.CAUTION—Replace head gasket with a new one each timethe head is removed to ensure proper sealing.
Air leaks at fittings:Fittings are not tight enough.Tighten fittings where air can be heard escaping. Checkfittings with soapy water solution. DO NOT OVERTIGHTEN.
Air leaks in air tank:Defective or rusted air tank.Air tank must be replaced. DO NOT ATTEMPT TO REPAIR AIR TANK!
Air blowing from inlet filter:Damaged inlet (reed) valve.Contact Consumer Helpline at 1-800-423-3598.
Insufficient pressure at air tool or air accessory:Pressure regulator knob is not turnedto high enough pressure.Adjust pressure regulator knob to proper setting.
Defective motor/pressure regulatorswitch.Replace.
Restricted air intake filter.Clean or replace the filter element.
Air leaks.Check for leaks by applying soap solution to all fittings andconnections. Bubbles will appear at leakage points. Tighen orreplace leaking fittings or connections as needed.
Hose or hose connections are toosmall or long.Replace with larger hose or connectors.
Air compressor is not large enough forair requirement.Check the accessory air requirement. If it is higher than theCFM or pressure supply of the air compressor, you need alarger air compressor.
Air compressor not makingenough air:Restricted air intake filter.Clean or replace the filter element.
Leaking (reed) valve.Drain air tank and measure pump up time. Compare tospecifications. If lower, remove pump head and inspect valveplate, valve seats, and valve reeds. Clean or replace as needed.
Restricted pilot valve.Clean or replace.
Low compression.Low pressure may be due to worn piston rings and cylinderwalls. Inspect for excessive wear and replace worn parts asneeded.
Excessive oil consumption:Restricted air intake filter.Clean or replace air filter element.
Air compressor on unlevel surface.Do not incline the air compressor more than 10 degrees inany direction while running.
Crankcase overfilled with oil.Drain oil. Refill to proper level with 30 weight non-detergentair compressor oil
Plugged oil dipstick vent.Clean and check breather for proper ventilation.
Oil leaks.Repair.
Worn piston rings or scored cylinder.Replace worn or damaged parts as needed.
Improper oil viscosity.Drain oil. Refill to proper level with 30 weight non-detergentair compressor oil.
Oil has milky appearance:Water in oil due to condensation.Change oil and move air compressor to a less humidenvironment.
Moisture in discharge air:Condensation in air tank caused byhigh level of atmospheric humidity orair compressor is not running longenough.
Drain tank after every use. Drain air tank more often inhumid weather and use an air line filter.  
						

							PARTS LIST
15
NO.PART NO.DESCRIPTIONQTYNO.PART NO.DESCRIPTIONQTY
1830241-1Air Filter155830241-55Air Tank Assembly1
2830241-2Elbow Connector156830241-56Pressure Regulator1
3830241-3Bolt M8x103457830241-57Quick Coupler1
4830241-4Cylinder Head158830241-58Handle Grip1
5830241-5Cylinder Head Gasket1
6830241-6Valve Plate1
7830241-7Valve Plate Gasket 1
8830241-8Pin _31
9830241-9Reed Valve1
10830241-10Cylinder1
11830241-11Cylinder Gasket1
12830241-12Piston Ring3
13830241-13Piston1
14830241-14Piston Pin Circlip _122
15830241-15Connecting Rod1
16830241-16Crankcase1
17830241-17Crank1
18830241-18Bolt M8x301
19830241-19Rubber Crankcase Cover Gasket1
20830241-20Oil Fill Breather Plug1
21830241-21O-Ring _13x_2.51
22830241-22Crank Case Cover1
23830241-23Screw M5x141
24830241-24Oil Sight Glass1
25830241-25Oil Sight Glass Gasket1
26830241-26Bolt M12x1.51
27830241-27Bearing 62041
28830241-28Sealing Ring1
29830241-29Capacitor (140uf)1
30830241-30External Tooth Lock Washer _81
31830241-31Nut M81
32830241-32Piston Pin2
33830241-33Fan Cover1
34830241-34Screw M5x82
35830241-35Screw ST3.9x192
36830241-36Circlip for Motor Shaft 141
37830241-37Cooling Fan1
38830241-38Bolt M5x1034
39830241-39Motor Cover1
40830241-40External Tooth Lock Washer1
41830241-41Bearing 62031
42830241-42Stator1
43830241-43Rotor1
44830241-44Power Cord1
45830241-45Pressure Gauge2
46830241-46Pressure Switch1
47830241-47Wiring Harness1
48830241-48Unloader Tube1
49830241-49High Pressure Tube1
50830241-50Check Valve1
51830241-51Rubber Footpad4
52830241-52Screw ST3.94
53830241-53Bolt M8x254
54830241-54Bolt M8x304  
						

							16
PARTS DIAGRAM  
						

							FACTORY RE-MANUFACTURED 30 DAY WARRANTY
ALLTRADE TOOLS LLC AIR COMPRESSORS
Express and Exclusive Limited Warranty to Original Retail Buyer
Alltrade Tools LLC (hereinafter “Alltrade”) expressly warrants to the original retail purchaser of the accompanying air compressor and no one
else all parts of the product (except those parts referred to below which are specifically excluded from such warranty (see Exclusions)) to be free
from defects in materials for thirty (30) days from the original date of purchase:
The date of purchase shall be the date of shipment to the original purchaser, or the date the original purchaser took possession, custody or
control of the product, whichever occurred first. This warranty shall be null and void if the product or any component thereof is modified or
altered. This warranty does not apply to any other product and/or component thereof manufactured or distributed by Alltrade, and does not
apply to products and/or components thereof designed, manufactured and/or assembled by others, for which Alltrade makes no warranties
whatsoever. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF.
Warranty Performance 
By purchasing the product, purchaser expressly acknowledges and agrees that their sole and exclusive remedy under this warranty shall be
strictly limited to the repair or replacement of any covered nonconforming items or parts thereof provided that any such nonconforming item
and/or part is promptly returned to Alltrade’s facility postage pre-paid and insured (ADDRESS:ALLTRADE Warranty Claims & Repair, 1431 Via
Plata, Long Beach, CA 90810, Attn: Customer Service (TELEPHONE: (800) 522-9008)) within the applicable warranty period, with a written
request by purchaser that Alltrade repair and/or replace the nonconforming item and/or part. We recommend that you keep the original
product packaging in the event you need to ship the unit. We suggest the package be insured against loss or in transit damage. When sending
your product include your name, address, phone number, dated proof of purchase (or copy), and a statement about the nature of problem.
Warranty coverage is conditioned upon purchaser furnishing Alltrade with adequate written proof that they are the original purchaser and of
the original purchase date. Parts returned, freight prepaid and insured, to Alltrade’s facility (see above address) will be inspected and, at
Alltrade’s option, repaired and/or replaced free of charge if found to be defective and subject to warranty. Alltrade retains the sole discretion to
determine whether any item or part is nonconforming and, if so, whether the item and/or part will be repaired and/or replaced. If Alltrade
chooses to replace the product, it may replace it with a new or reconditioned one of the same or comparable design. The repaired or replaced
unit will be warranted under the terms of the remainder of applicable warranty period(s). Typically, covered defective parts not subject to normal
wear and tear or other exclusions will be repaired or replaced, at Alltrade’s option, during the above stated warranty periods. Alltrade’s repair
and/or replacement of any nonconforming item and/or part thereof shall constitute fulfillment of all obligations to the purchaser. Alltrade shall
not be responsible or liable for any expense, including freight charges, or repairs made outside Alltrade’s facility, unless expressly agreed to by
Alltrade in writing. Under no circumstances shall Alltrade bear any responsibility for loss of the unit, loss of time or rental, inconvenience,
commercial loss or consequential damages.
Exclusions
This warranty does not cover parts damaged due to normal wear, abnormal conditions, misapplication, misuse, abuse, accidents, operation at
other than recommended pressures or temperatures, improper storage or freight damage. Parts damaged or worn by operation in dusty
environments are not warranted. Failure to follow recommended operating and maintenance procedures also voids warranty.
The following additional items are not covered under this warranty: pump or valve failure caused by rain, excessive humidity, corrosive
environments or other contaminants; cosmetic defects that do not interfere with compressor functionality; and rusted tanks, including but not
limited to rust due to improper drainage or corrosive environments.
This warranty shall not apply when: the air compressor has been used for commercial or rental purposes; defects in materials or workmanship
or damages result from repairs or alterations which have been made or attempted by others or the unauthorized use of nonconforming parts;
damage is due to abuse (including overloading of the air compressor beyond capacity), improper maintenance, neglect or accident, or the
damage is due to use of the air compressor after partial failure or use with improper accessories.
Alltrade will not be liable for the following: labor charges, loss or damage resulting from improper operation, maintenance or repairs made by
other persons; pre-delivery services such as assembly, oil or lubricants, and adjustment; maintenance services that are normally required to
maintain the air compressor.
The use of other than genuine Alltrade Repair Parts will void warranty.
Warranty Disclaimers 
EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS. EXCEPT FOR THE LIMITED
WARRANTY PROVIDED ABOVE, ALL OTHER EXPRESS WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS BY ALLTRADE AND/OR ITS
REPRESENTATIVE(S) REGARDING THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE AIR COMPRESSOR OR ANY
COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION,
WRITTEN OR ORAL, ARISES BY OPERATION OF LAW AND/OR EQUITY AND/OR BY ANY ACT OR OMISSION OF ALLTRADE AND/OR ITS
REPRESENTATIVE(S), OR THE BUYER, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE AND/OR ITS REPRESENTATIVES.
PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS AND/OR CAUSES OF ACTION
ARISING THEREFROM OR BASED THEREON. PURCHASER’S SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE.
EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE. NO WARRANTY, ORAL OR WRITTEN, OTHER THAN THE ABOVE WARRANTY IS MADE WITH REGARD TO THIS AIR
COMPRESSOR. ALL EXPRESS AND/OR IMPLIED WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS BY ALLTRADE AND/OR ITS
REPRESENTATIVE(S) REGARDING THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE AIR COMPRESSOR OR ANY
COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION,
17  
						

							WRITTEN OR ORAL, ARISES BY OPERATION OF LAW AND/OR EQUITY AND/OR BY ANY ACT OR OMISSION OF ALLTRADE AND/OR ITS
REPRESENTATIVE(S), OR THE PURCHASER, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE AND/OR ITS
REPRESENTATIVES. PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS AND/OR
CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON.
PURCHASER’S SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE.
Limitation Of Liability
IN NO EVENT SHALL ALLTRADE AND/OR ITS REPRESENTATIVE(S) BE LIABLE FOR INDIRECT, INCIDENTAL, SPECIAL AND/OR CONSEQUENTIAL
DAMAGES OF ANY KIND ARISING OUT OF OR RELATED TO, DIRECTLY OR INDIRECTLY, ANY BREACH OF ANY PROVISION OF ANY AGREEMENT
BETWEEN ALLTRADE AND/OR ITS REPRESENTATIVE(S) AND PURCHASER, ANY WARRANTY HEREUNDER, AND/OR THE EXISTENCE, DESIGN,
MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF ANY ITEM(S) SOLD HEREUNDER EVEN IF ALLTRADE AND/OR ITS REPRESENTATIVE(S)
HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH DAMAGES. IN NO EVENT, WHETHER AS A RESULT OF A BREACH OF CONTRACT,
WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL ALLTRADE’S AND/OR ITS REPRESENTATIVE(S)’ LIABILITY EXCEED THE
PRICE OF THE AIR COMPRESSOR. ANY AND ALL LIABILITY CONNECTED WITH THE USE OF THIS AIR COMPRESSOR SHALL TERMINATE UPON
THE EXPIRATION OF THE WARRANTY PERIODS SPECIFIED ABOVE.
Limitations on Warranty Disclaimers 
Some states do not allow limitations on how long an implied warranty lasts and some states do not allow the exclusion or limitation of the
incidental or consequential damages, so part or all of the above limitations or exclusions may not apply to you. This warranty gives you specific
legal rights, and you may also have other rights which vary from state to state.
If your product is not covered by this warranty, please call our Customer Service Department at (800) 423-3598 for general repair information
and charges.
18