AllTrade Tradespro 2 Gal Air Compressor 835081 User Manual

							FOR 
CUSTOMER 
SERVICE
POUR 
LE SERVICE 
APRÉS 
VENTE
OU DU CONSOMMATEUR
PARA 
EL SERVICIO 
PARA 
EL CONSUMIDOR
1-800-423-3598
Model 
#835081
Modelo 
#835081
ALLTRADE 
TOOLS 
LLC
1431 
VIA 
PLATA, 
LONG 
BEACH, 
CA 
90810-1462
www.alltradetools.comMADE 
IN / FABRIQUÉ 
EN 
/ HECHO 
EN 
CHINA
© COPYRIGHT 
2003, 
ALLTRADE 
TOOLS 
LLC 
REV. 
1 
Please 
retain 
these 
instructions 
for future 
reference.
If you 
encounter 
any 
problems 
or difficulties, 
 
please 
contact 
our 
toll 
free 
Customer 
Service 
Department 
at:
1-800-423-3598
1-310-522-9008 
(California 
only)
1-310-522-9066 
Fax
Prière 
de conser
ver 
ces 
instructions 
pour 
pouvoir 
y référer 
à lavenir
.
En cas 
de problèmes 
ou de difficultés, 
prière 
de contacter 
notre 
Service 
Après-V
ente 
au numéro 
d’appel 
gratuit:
1-800-423-3598 
     
1-310-522-9008 
(En 
Californie 
seulement)
1-310-522-9066 
Fax
Por 
favor
, guarde 
estas 
instrucciones 
para 
que 
le sirvan 
de referencia 
en el futuro.
Si usted 
se encuentra 
con 
algún 
problema 
o dificultad, 
por 
favor
, comuníquese 
con 
nuestro 
Departamento 
de Servicios 
para 
el Consumidor
, llamando 
de forme 
gratuita 
al:
1-800-423-3598 
     
1-310-522-9008 
(solamente 
dentro 
del 
estado 
de California)
1-310-522-9066 
Fax
2
Air 
Compressor
Compresseur 
D’Air
Compresor 
de 
Aire
Gallon  
						

							3
2
2 GALLON 
AIR 
COMPRESSOR
• Do 
not 
pull 
on power 
cord 
to disconnect 
it from 
the 
outlet. 
Keep 
cord 
away 
form 
heat, 
oil, 
and 
sharp 
edges.
• NEVER 
move 
the 
unit 
by pulling 
on the 
air hose. 
Use 
the 
handle 
provided 
on the 
top 
of the 
unit.
• DO 
NOT 
reach 
over 
or across 
running 
machines.
• To reduce 
the 
risk 
of injur
y, close 
super
vision 
is necessar
y when 
the 
compressor 
is used 
near 
children. 
• DO 
NOT 
ALLOW 
CHILDREN 
TO 
OPERA
TE THE 
COMPRESSOR 
AT ANY 
TIME.
• DO 
NOT 
MAKE 
ANY 
MODIFICA
TIONS 
TO 
ANY 
OF THE 
COMPONENTS. 
Units 
with 
broken 
or missing 
parts, 
or without
protective 
housings 
or covers 
in place 
should 
NEVER 
be operated.
• Do 
not 
leave 
the 
compressor 
unattended 
while 
the 
power 
switch 
is in the 
“I” (ON) 
position. 
When 
the 
power 
switch
is in the 
“I” (ON) 
position, 
pump 
motor 
may 
start 
at any 
time 
without 
warning.
• Do 
not 
overpressurize 
tank.
• If compressor 
has 
been 
dropped 
or impacted 
in any 
manner
, check 
tank 
for 
cracks 
before 
using.
• Never 
attempt 
to fill or operate 
compressor 
if any 
air leak 
is detected.
• Do 
not 
modify 
or attempt 
to service 
tank. 
• Do 
not 
store 
liquids 
in tank.
• This 
product 
is not 
intended 
for 
use 
as a portable 
breathing 
device 
or to disperse 
any 
type 
of liquid.
• Maximum 
pressure: 
100 
PSI.
Grounding 
Instructions:
1. This 
product 
shall 
be grounded. 
In the 
event 
of an electrical 
short 
circuit, 
grounding 
reduces 
the 
risk 
of electric 
shock. 
2. This 
product 
is equipped 
with 
a cord 
having 
a grounding 
wire 
with 
an appropriate 
grounding 
plug.
3. The 
plug 
must 
be plugged 
into 
an outlet 
that 
is properly 
installed 
and 
grounded 
in accordance 
with 
all local 
codes 
and
ordinances.DANGER: 
Improper 
installation 
of the 
grounding 
plug 
can 
result 
in a risk 
of electric 
shock. 
If repair 
or replacement 
of
the 
cord 
is necessar
y, do not 
connect 
the 
grounding 
wire 
to either 
flat 
blade 
terminal. 
The 
wire 
with 
green 
insulation
with 
or without 
yellow 
stripes 
is the 
grounding 
wire.
4. Check 
with 
a qualified 
electrician 
or serviceman 
if the 
grounding 
instructions 
are 
not 
completely 
understood, 
or if in
doubt 
as to whether 
the 
product 
is properly 
grounded. 
Do 
not 
modify 
the 
plug 
provided; 
if it will 
not 
fit the 
outlet,
have 
the 
proper 
outlet 
installed 
by a qualified 
electrician.
Extension 
Cord:
1. Use 
of an extension 
cord 
with 
this 
product 
is NOT 
RECOMMENDED. 
If you 
must 
use 
an extension 
cord, 
use 
only
extension 
cords 
that 
are 
intended 
for 
outdoor 
use. 
Use 
only 
extension 
cords 
having 
an electrical 
rating 
not 
less 
than
the 
rating 
of the 
product. 
2. Examine 
extension 
cord 
before 
use. 
DO 
NOT 
USE 
DAMAGED 
EXTENSION 
CORDS! 
3. Always 
disconnect 
the 
extension 
cord 
from 
the 
receptacle 
before 
disconnecting 
the 
product 
from 
the 
extension 
cord.
4. WARNING 
– to reduce 
the 
risk 
of electrocution, 
keep 
all connections 
dry and 
off the 
ground. 
Do 
not 
touch 
the 
plug
with 
wet 
hands.
Assembly 
Instructions:
1.  After 
opening 
the 
carton, 
please 
remove 
all parts 
and 
check 
against 
photograph 
on carton. 
If any 
parts 
are 
missing,
please 
call 
Alltrade 
at 1-800-423-3598.
2.  Close 
the 
drain 
valve 
on the 
bottom 
of the 
air tank 
by turning 
the 
valve 
clockwise 
until 
fully 
closed.
3.  Attach 
the 
air hose 
to the 
compressor 
regulator 
valve. 
Use 
included 
Teflon 
thread-sealing 
tape 
on the 
threads 
to
make 
sure 
you 
have 
an airtight 
connection. 
Do 
not 
overtighten 
fittings. 
4.  Attach 
the 
desired 
accessor
y to the 
end 
of the 
hose. 
Use 
included 
Teflon 
thread-sealing 
tape 
on the 
threads 
to make
sure 
you 
have 
an airtight 
connection. 
Do 
not 
overtighten 
fittings.
WARNING: 
READ 
AND 
UNDERST
AND 
ALL 
PRODUCT 
FEA
TURES 
PRIOR 
TO 
OPERA
TING 
COMPRESSOR
Product 
Features 
1. AUTOMA
TIC 
ON/OFF 
PRESSURE 
SWITCH:
This 
compressor 
is equipped 
with 
an automatic 
on/off 
pressure 
switch. 
The 
compressor 
will 
only 
run 
when 
the 
switch 
is
in the 
“I” (ON) 
position. 
Once 
the 
tank 
has 
reached 
the 
desired 
preset 
pressure 
(see 
Operating 
Instructions), 
the 
pump
motor 
will 
automatically 
shut 
off. 
While 
the 
switch 
is in the 
“I” (ON) 
position, 
the 
pump 
motor 
will 
automatically 
turn
WARNINGAVER
TISSEM
back 
on once 
the 
pressure 
in the 
tank 
drops 
below 
the 
minimum 
preset 
pressure. 
Do 
not 
leave 
the 
compressor 
unattended 
while 
the 
power 
switch 
is in the 
“I” (ON) 
position.
2. REGULA
TOR:
The 
regulator 
allows 
you 
to select 
the 
amount 
of air pressure 
that 
is output 
through 
the 
air hose 
into 
tools 
and
accessories. 
Please 
refer 
to the 
air deliver
y requirements 
of your 
tools 
for 
the 
proper 
pressure 
settings. 
 
3. TANK 
PRESSURE 
GAUGE:
The 
tank 
pressure 
gauge 
provides 
a reading 
of the 
air pressure 
inside 
of the 
compressor 
tank. 
4. SAFETY 
VALVE:
This 
compressor 
is equipped 
with 
a safety 
valve 
switch 
that 
will 
engage 
when 
the 
pressure 
in the 
tank 
exceeds 
the 
maximum 
rated 
pressure. 
DO 
NOT 
attempt 
to modify 
or remove 
safety 
valve. 
5. TANK 
DRAIN 
FITTING:
Water 
is produced 
whenever 
air is compressed. 
It is critical 
to drain 
water 
from 
the 
air tank 
on this 
compressor 
frequently
. If unit 
is used 
only 
occasionally
, tank 
should 
be drained 
after 
each 
use 
and 
prior 
to the 
next 
use. 
To drain 
the 
tank, 
slowly 
open 
the 
tank 
drain 
fitting 
by turning 
clockwise. 
Once 
all water 
has 
drained 
out, 
close 
the 
fitting 
securely
.  NOTE: 
tank 
will 
not 
pressurize 
while 
fitting 
is open. 
6. THERMAL 
SHUTDOWN 
SWITCH:
The 
electric 
motor 
is equipped 
with 
an automatic 
thermal 
overload 
protector
. If the 
unit 
is overheating, 
the 
motor 
will
automatically 
shut 
down. 
Turn 
the 
unit 
off and 
wait 
5-10 
minutes 
before 
turning 
the 
unit 
back 
to the 
“I” (ON) 
position. 
If the 
unit 
shuts 
down 
again, 
please 
contact 
the 
manufacturer 
for 
assistance.
Operating 
Instructions:
START UP:
1. Slowly 
open 
tank 
drain 
by turning 
clockwise. 
Allow 
any 
water 
in tank 
to drain 
out. 
Close 
fitting 
securely
.
2. Before 
connecting 
the 
compressor 
to the 
grounded 
outlet, 
check 
for 
broken 
components 
and 
accessories, 
and 
check
for 
damage 
to the 
hose.
3. Make 
sure 
the 
power 
switch 
is turned 
“O” 
(OFF) 
position.
4. Plug 
the 
unit 
into 
a grounded 
outlet.
5. Attach 
desired 
tool 
to the 
end 
of the 
air hose.
6. Turn 
the 
switch 
on the 
“I” (ON) 
position.
7. Adjust 
regulator 
knob 
to desired 
pressure 
level 
once 
the 
pump 
has 
shut 
off and 
the 
compressor 
has 
stopped 
running.
STORAGE:1. Disconnect 
unit 
from 
grounded 
outlet.
2. Disconnect 
tools 
and/or 
accessories 
from 
the 
air hose.
3. Locate 
drain 
valve 
on bottom 
side 
of tank.
4. Open 
drain 
valve 
to release 
remaining 
pressurized 
air and 
moisture 
from 
the 
air tank. 
Moisture 
build-up 
in the 
tank 
is
normal 
with 
air compressors, 
so a small 
amount 
of water 
may 
come 
out 
while 
draining 
the 
tank. 
Draining 
the 
tank 
is
vital 
for 
the 
longevity 
and 
safety 
of your 
air compressor
.
5. Close 
valve 
and 
store 
the 
compressor 
in a cool, 
dry place.
MAINTENANCE:1. This 
compressor 
is supplied 
with 
a closed 
lubrication 
system, 
so no lubrication 
is needed.
2. Periodically 
drain 
tank 
of excess 
moisture. 
Excess 
moisture 
in the 
tank 
will 
result 
in wear 
and 
tear 
on tools 
and 
accessories.3.Fuse 
Replacement
- Disconnect 
power 
cord 
from 
electrical 
outlet 
prior 
to fuse 
replacement. 
 
- Replace 
with 
5A 250V 
Glass 
Tube 
Fuse 
only!  
						

							5
4
Troubleshooting:1. The 
compressor 
will 
not 
run.
Probable 
cause: 
1. No power
, or the 
switch 
is in the 
“OFF” 
position.
2. Motor 
overheated
3. Tank 
Pressure 
at maximum
Solutions:1. Make 
sure 
the 
compressor 
is plugged 
in and 
the 
switch
is in the 
“ON 
position.
2.Allow 
compressor 
to cool 
for 5-10 
minutes 
until 
thermal
overload 
switch 
resets.
3. Release 
air from 
tank
2 .Tank 
pressure 
drops 
when 
compressor 
shuts 
off.
Probable 
cause:
1.Loose 
drain 
valve
2.Loose 
connection 
at regulator 
or pressure 
switch
Solutions:1. Tighten 
drain 
valve
2. Check 
connections 
for leaks
3. Compressor 
runs 
continuously
.
Probable 
cause: 
1. Excessive 
water 
in tank
2. Humidity 
too 
high
Solutions:1. Decrease 
usage 
or increase 
size 
of compressor
2. Check 
all connections 
for leaks
4. Excessive 
starting 
and 
stopping.
Probable 
cause:
1.Excessive 
water 
build-up 
in tank
Solutions:1.Drain 
tank 
through 
drain 
valve.