AllTrade Kawasaki 22 Gal Wet Dry Vac 840121 User Manual

							MODEL#840121
2.2 
GALLON 
WET
/DRY
VACUUM
/BLOWER 
INSTRUCTION 
MANUAL
FOR 
CUSTOMER 
SERVICE
POUR 
LE SERVICE 
APRÉS 
VENTE
OU 
DU 
CONSOMMATEUR
PARA 
EL SERVICIO
PARA 
EL CONSUMIDOR
1-800-590-3723
Printed 
in China 
87-1904-60957
KAWASAKI™
IS A TRADEMARK 
LICENSED 
BY KAWASAKI™
MOTORS 
CORP
., U.S.A., 
WHICH 
DOES 
NOT 
MANUF
ACTURE 
OR 
DISTRIBUTE 
THIS 
PRODUCT
. CONSUMER 
INQUIRES 
SHOULD 
BE
DIRECTED 
TO:
©COPYRIGHT 
2006 
ALLTRADE 
TOOLS, 
LLC.
1431 
VIA PLATA
LONG 
BEACH, 
CA 90810-1462 
USA
840121 
– 2.2 Gallon 
Corded 
Wet/Dr
y Vacuum/Blower_Rev 
9/28/06
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY,OPERATION,
MAINTENANCE AND STORAGE OF THIS PRODUCT.BEFORE USE,READ CAREFULLY AND 
UNDERST
AND 
ALL 
CAUTIONS,
WARNINGS,
INSTR
UCTIONS 
AND 
PRODUCT 
LABELS.
FAILURE 
TO 
DO
SO 
COULD 
RESUL
T IN SERIOUS 
PERSONAL 
INJUR
Y AND/OR 
PROPER
TY 
DAMAGE.
IF YOU 
SHOULD 
HAVE 
ANY 
QUESTIONS 
OR 
EXPERIENCE 
A PROBLEM 
WITH 
YOUR 
ALL
TRADE 
PRODUCT
,DO 
NOT 
RETURN 
THIS 
PRODUCT 
TO 
THE 
STORE.
PLEASE 
CALL 
OUR 
CUSTOMER 
SERVICE
DEP
ARTMENT 
AT 1-800-590-3723
.BEFORE 
YOU 
CALL,
HAVE 
THE 
FOLLOWING 
INFORMA
TION 
AVAILABLE:MODEL No.,DATE PURCHASED AND STORE LOCATION.AN ALLTRADE 
REPRESENT
ATIVE 
CAN 
RESOL
VE 
YOUR 
PROBLEM 
OVER 
THE 
PHONE.
IF YOU 
WOULD 
LIKE 
TO 
MAKE
A SUGGESTION 
OR 
COMMENT
,GIVE 
US 
A CALL 
OR 
EMAIL 
US 
AT:INFO@ALL
TRADETOOLS.COM.
YOUR 
FEEDBACK 
IS VITAL 
TO 
US.  
						

							CONGRA
TULA
TIONS!
Thanks for choosing this product. At Alltrade, our aim is to provide you with quality
products 
at 
an 
affordable 
price, 
and 
we 
want 
you 
to 
be 
totally 
satisfied 
with 
your
product 
and 
our 
Customer 
Ser
vice. 
If 
any 
help 
and 
advice 
is 
needed, 
please 
contact 
us 
at 
1-800-590-3723. 
Properly 
cared 
for
, this 
tool 
will 
give 
you 
many 
years 
of 
satisfaction.
INTENDED 
USE
This 
tool 
is intended 
for 
consumer 
use 
only
.
GENERAL 
SAFETY 
RULES 
– FOR 
ALL 
ELECTRIC 
POWER 
TOOLS
READ 
AND 
UNDERST
AND 
ALL 
INSTRUCTIONS.
Failure 
to
follow 
all 
instructions 
listed 
below 
may 
result 
in 
electric 
shock, 
fire 
and/or 
serious 
personal 
injur
y.
RECOGNIZE 
SAFETY 
SYMBOLS, 
WORDS 
AND 
LABELS
The safety instructions provided in this manual are not intended to cover all possible
conditions 
and 
practices 
that 
may 
occur 
when 
operating, 
maintaining 
and 
cleaning
power 
tools.
Always 
use 
common 
sense 
and 
pay 
particular 
attention 
to 
all 
the 
DANGER
, 
WARNING
, CAUTION
and 
NOTE
statements 
of 
this 
manual.
This 
is the 
safety 
alert 
symbol. 
It is used 
to 
alert
you 
to 
potential 
personal 
injur
y hazards. 
Obey 
all
safety 
messages 
that 
follow 
this 
symbol 
to 
avoid
possible 
injur
y or 
death.
DANGER
indicates an imminently hazardous 
situation 
which, 
if not 
avoided, 
will 
result 
in death
or 
serious 
injur
y.
WARNING
indicates a potentially hazardous 
situation 
which, 
if not 
avoided, 
could 
result 
in
death 
or 
serious 
injur
y.
TABLE 
OF 
CONTENTS
CONGRA
TULA
TIONS!
 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
INTENDED 
USE
 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
SECTION 
ONE
GENERAL 
SAFETY 
RULES 
– FOR 
ALL 
ELECTRIC 
POWER 
TOOLS
 . . . .2
RECOGNIZE 
SAFETY 
SYMBOLS, 
WORDS 
AND 
LABELS
 . . . . . . . .
2-3
IMPOR
TANT 
SAFEGUARDS
 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
ELECTRICAL 
SAFETY
 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
SERVICE
 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
SECTION 
TWO
SAFETY 
RULES 
FOR 
WET
/DR
Y VACUUM
/BLOWERS
 . . . . . . . . . . . . .
5
VACUUM 
SAFETY 
 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-6
BLOWING 
SAFETY
 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
GROUNDING 
INSTRUCTIONS
 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-7
EXTENSION 
CORD 
USAGE
 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
SYMBOLS
 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
SECTION 
THREE
FUNCTIONAL 
DESCRIPTION
 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
OPERA
TING 
THE 
WET
/DR
Y VACUUM
/BLOWER
 . . . . . . . . . . . . . . . . .
9-11
DR
Y VACUUMING
 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
WET 
VACUUMING
 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
EMPTYING 
THE 
DUST 
CONT
AINER
 . . . . . . . . . . . . . . . . . . . . . . . .
10
BLOWER 
USE
 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-11
SECTION 
FOUR
MAINTENANCE 
AND 
CLEANING
 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11-13
ACCESSORIES
 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
SPECIFICA
TIONS
 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
OTHER 
CONSUMER 
DO-IT
-YOURSELF 
(DIY) 
TOOLS
 . . . . . . . . . . . . . .
14
SECTION 
FIVE
3 YEAR 
LIMITED 
WARRANTY
 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15-18
1
2  
						

							ELECTRICAL 
SAFETY
Double 
insulated 
tools 
are 
equipped 
with 
a polarized 
plug 
(one 
blade 
is
wider 
than 
the 
other
.) This 
plug 
will 
fit 
in 
a polarized 
outlet 
only 
one 
way
. If
the 
plug 
does 
not 
fit 
fully 
in 
the 
outlet, 
reverse 
the 
plug. 
If it still 
does 
not 
fit,
contact 
a qualified 
electrician 
to 
install 
a polarized 
outlet. 
Do 
not 
change 
the
plug 
in 
any 
way
.Double 
insulation 
eliminates 
the 
need 
for 
the 
three 
wire
grounded 
power 
cord 
and 
grounded 
power 
supply 
system. 
Avoid 
body 
contact 
with 
grounded 
surfaces 
such 
as 
pipes, 
radiators, 
ranges
and 
refrigerators
. There 
is 
an 
increased 
risk 
of 
electric 
shock 
if your 
body 
is
grounded.Do 
not 
expose 
power 
tools 
to 
rain 
or 
wet 
conditions.
Water 
entering 
a power
tool 
will 
increase 
the 
risk 
of 
electric 
shock.
Do 
not 
abuse 
the 
cord. 
Never 
use 
the 
cord 
to 
carr
y the 
tool 
or 
pull 
the 
plug
from 
an 
outlet. 
Keep 
the 
cord 
away 
from 
heat, 
oil, 
sharp 
edges, 
or 
moving
parts. 
Replace 
damaged 
cords 
immediately
. Damaged 
cords 
increase 
the 
risk
of 
electric 
shock.
When 
operating 
the 
tool 
outside, 
use 
an 
outdoor 
extension 
cord 
marked 
“W
-
A” 
or 
“W
.”These 
cords 
are 
rated 
for 
outdoor 
use 
and 
reduce 
the 
risk 
of 
elec-
tric 
shock.
SERVICE
Tool 
ser
vice 
must 
be 
performed 
only 
by 
qualified 
repair 
personnel.
Ser
vice 
or
maintenance 
by 
unqualified 
personnel 
may 
result 
in a risk 
of 
injur
y. 
When 
ser
vicing 
a tool, 
use 
only 
identical 
replacement 
parts. 
Follow 
instructions
in 
the 
Maintenance 
section 
of 
this 
manual. 
Use 
of 
unauthorized 
parts 
or 
failure 
to
follow 
Maintenance 
Instructions 
may 
create 
a risk 
of 
shock 
or 
injur
y.
4
CAUTION
indicates a potentially hazardous 
situation 
which, 
if 
not 
avoided, 
may 
result 
in
minor 
or 
moderate 
injur
y.
CAUTION
used 
without 
the 
safety 
alert 
symbol
indicates 
a potentially 
hazardous 
situation 
which,
if not 
avoided, 
may 
result 
in property 
damage.
NOTEprovides additional information that is useful
for 
proper 
use 
and 
maintenance 
of 
this 
tool. 
If a
NOTE 
is indicated 
make 
sure 
it is fully 
understood.
IMPOR
TANT 
SAFEGUARDS
People 
with 
electronic 
devices, 
such 
as 
pacemakers, 
should 
consult 
their
physician(s) 
before 
using 
this 
product. 
Operation 
of 
electrical 
equipment 
in
close 
proximity 
to 
a heart 
pacemaker 
could 
cause 
interference 
or 
failure 
of
the 
pacemaker
.
WARNING:
Some 
dust 
created 
by 
power 
sanding, 
sawing, 
grinding, 
drilling 
and
other 
construction 
activities 
contains 
chemicals 
known 
to 
the 
State 
of 
California
to 
cause 
cancer
, birth 
defects 
or 
other 
reproductive 
harm.
Some 
examples 
of 
these 
chemicals 
are:
• Lead 
from 
lead-based 
paints. 
• Crystalline 
silica 
from 
bricks 
and 
cement 
and 
other 
masonr
y products,
and 
arsenic 
and 
chromium 
from 
chemically-treated 
lumber
.
Your 
risk 
from 
these 
exposures 
varies, 
depending 
on 
how 
often 
you 
do 
this 
type
of 
work. 
To reduce 
your 
exposure 
to 
these 
chemicals: 
work 
in 
a well 
ventilated
area, 
and 
work 
with 
approved 
safety 
equipment, 
such 
as 
dust 
masks 
that 
are
specially 
designed 
to 
filter 
out 
microscopic 
particles.
WARNING: 
Handling 
the 
power 
cord 
on 
corded 
products 
may 
expose 
you 
to
lead, 
a chemical 
known 
to 
the 
State 
of 
California 
to 
cause 
cancer 
and 
birth
defects 
or 
other 
reproductive 
harm.
Wash 
hands 
after 
handling.
SA
VE 
THESE 
INSTRUCTIONS 
FOR 
FUTURE 
REFERENCE.
3  
						

							NEVER
vacuum 
up 
smoldering 
cigarette 
butts, 
hot 
ashes 
or 
any 
other 
burning 
mate-
rial. 
This 
may 
cause 
the 
unit 
to 
burst 
into 
flame. 
NEVER
use 
the 
vacuum 
if the 
filter 
is wet 
or 
missing.
BLOWING 
SAFETY
DO 
NOT
use 
Wet/Dr
y Vacuum/Blower 
as 
a sprayer
.
DO 
NOT
point 
the 
nozzle 
or 
exhaust 
vents 
toward 
your 
eyes, 
ears 
or 
hair
. DO 
NOT
point 
nozzle 
at bystanders 
or 
animals. 
Keep 
air 
discharge 
directed 
at the 
work 
area. 
Keep 
children 
away 
while 
blower 
is in use.
USE 
ONL
Yfor 
dust, 
dirt, 
leaves 
and 
other 
light 
debris. 
This 
product 
should 
not 
be
used 
for 
heavy-duty 
blowing.If 
you 
have 
a pacemaker
, consult 
your 
doctor 
before
using 
this 
product.
This 
equipment 
could 
cause 
pacemaker 
inter
ference 
or 
fail-
ure 
when 
used 
at close 
quarters.GROUNDING 
INSTRUCTIONS
The 
electrical 
power 
sour
ce 
for 
this 
Wet/Dr
y Vacuum/Blower 
MUST
be 
grounded 
in
order 
prevent 
possible 
electric 
shock 
or 
even 
death 
should 
the 
tool 
malfunction 
or
breakdown. 
Grounding 
provides 
a path 
of 
least 
resistance 
for 
electric 
current 
thus
reducing 
the 
risk 
of 
electrical 
shock. 
The 
power 
sour
ce 
must 
also 
use 
a minimum
20A 
ser
vice 
and 
not 
used 
if other 
power 
tools 
on 
the 
same 
circuit 
are 
in use.
This 
Wet/Dr
y Vacuum/Blower 
is equipped 
with 
a grounded 
3-wire 
power 
cord 
with
a 3-prong 
plug. 
If the 
power 
cord 
will 
not 
fit 
into 
the 
wall 
plug, 
an 
approved 
adapter
can 
be 
used 
as 
long 
as 
it is connected 
to 
the 
center 
screw 
in 
the 
wall 
plate. 
Never
modify 
the 
electrical 
plug 
by 
cutting 
off 
the 
grounding 
prong 
so 
it will 
fit 
into 
unap-
proved, 
un-grounded 
electrical 
receptacles. 
SAFETY 
RULES 
FOR 
WET 
/ DR
Y VACUUM 
/ BLOWERS
Never 
immerse 
the 
motor 
housing 
in 
water 
or 
liquid. 
Do 
not 
expose 
to 
rain
or 
other 
wet 
conditions.
Failure 
to 
keep 
motor 
housing 
dry will 
lead 
to 
risk 
of
electric 
shock.
Never 
handle 
the 
Wet/Dr
y Vacuum/Blower 
with 
wet 
hands.
Keep 
body 
away 
from 
grounded 
surfaces 
like 
refrigerators, 
pipes 
or 
ranges.
For 
additional 
protection 
against 
shock, 
connect 
the 
Wet/Dr
y Vacuum/Blower
to 
an 
outlet 
with 
a Ground 
Fault 
Circuit 
Interrupter 
(GFCI).
Keep the ventilation openings clear of dust, hair
, paper or anything else that
may 
restrict 
air 
flow
.
NEVER 
run 
the 
Wet/Dr
y Vacuum/Blower 
over 
the 
cord.
DO 
NOT 
vacuum 
toxic 
materials.
STOP 
using 
the 
Wet/Dr
y Vacuum/Blower 
immediately 
if the 
motor 
housing
breaks 
and 
the 
motor 
or 
any 
other 
electrical 
components 
are 
exposed.
Using
the 
Wet/Dr
y Vacuum/Blower 
in 
this 
condition 
could 
lead 
to 
shock 
or 
serious
personal 
injur
y.
Always 
wear 
safety 
goggles 
or 
eye 
protection 
when 
using 
this 
tool.
Operation
of 
the 
Wet/Dr
y Vacuum/Blower 
can 
result 
in 
foreign 
objects 
being 
blown 
into
the 
eyes 
resulting 
in severe 
eye 
damage. 
NOTE:
Ever
yday 
glasses 
are 
not 
SAFE-
TY 
GLASSES 
and 
not 
compliant 
with 
ANSI.
Use 
a dust 
mask 
or 
respirator 
for 
applications 
which 
generate 
dust.
Always 
wear 
an 
OSHA 
approved 
dusk 
mask 
or 
respirator 
when 
inside 
the
work 
area. 
Replace 
the 
filter 
daily
. NOTE:
Not 
all 
dust 
masks 
offer 
protection
from 
lead 
paint 
dust. 
Be 
sure 
to 
use 
the 
proper 
mask 
for 
the 
job.
Wear 
ear 
protection 
when 
using 
the 
Wet/Dr
y Vacuum/Blower 
for 
extended
hours 
or 
when 
using 
it in 
a noisy 
area.
Maintain 
labels 
and 
nameplates 
on 
the 
Vacuum/Blower
. These 
carr
y impor-
tant 
information. 
If unreadable 
or 
missing, 
contact 
Alltrade 
for 
a replacement.
VACUUM 
SAFETY
NEVER
leave 
Wet/Dr
y Vacuum/Blower 
running 
unattended.
NEVERvacuum in the presence of flammable or explosive materials such as gasoline,
natural gas, coal dust, magnesium dust, gun powder, hydrogen, solvents or lighter
fluid. Sparks inside the motor can cause flammable dust, liquid or gases to explode.
DO 
NOT 
vacuum 
toxic 
materials.
DO 
NOT
use 
for 
grooming 
animals.
5
UNGROUNDED AC RECEPTACLE
GROUNDED RECEPTACLE
GROUNDING ADAPTER
WET/DRY VACUUM/BLOWER
POWER CORD
WET/DRY VACUUM/BLOWER
POWER CORD
COVERPLATE
MOUNTING SCREW  
						

							FUNCTIONAL 
DESCRIPTION
CONTROLS 
AND 
COMPONENTS:
1. 
ON/OFF 
Switch
2. 
Hose 
with 
Swivel 
Ends
3. 
Nozzle
4. 
Vacuum 
Port
5. 
Blower 
Port
6. 
Power 
Cord
7. 
Cord 
Storage 
Indentation
COMPONENT
MODEL 
NUMBER
BARE VACUUM CLEANER
691252 
FIL
TER 
691286
NOZZLE 
691285
HOSE 
691284
8
If you 
have 
questions 
about 
hooking 
up 
the 
Wet/Dr
y Vacuum/Blower
, contact 
a 
certified 
electrical 
contractor 
to 
install 
the 
proper 
circuitr
y acceptable 
for 
this 
and
other 
power 
tools 
you 
use. 
Repair 
or 
replace 
any 
damaged 
electrical 
wiring 
IMMEDIA
TEL
Y.
EXTENSION 
CORD 
USAGE
Extension 
cords 
are 
not 
recommended 
for 
use 
with 
this 
Wet/Dr
y Vacuum/Blower
.
Extension 
cords, 
if used, 
must 
be 
properly 
grounded 
with 
a 3-prong 
plug 
on 
one
and 
a 3-hole 
receptacle 
on 
the 
other
. DO 
NOT 
use 
grounding 
adapters 
with 
an
extension 
cord. 
Extension 
cords 
must 
be 
UL 
listed 
and 
use 
a minimum 
of 
18
A.W
.G. 
wiring. 
Extension 
cords 
should 
never 
exceed 
25 
feet 
in 
length. 
Extension
cords, 
that 
are 
too 
long, 
cause 
a voltage 
drop 
over 
the 
extra 
distance 
causing 
the
Wet/Dr
y Vacuum/Blower 
motor 
to 
run 
slower 
with 
the 
possibility 
of 
causing 
dam-
age 
to 
the 
motor
. Using 
extension 
cords 
with 
smaller 
than 
the 
recommended 
wire
gauge 
run 
the 
risk 
of 
getting 
too 
hot, 
melting, 
and/or 
causing 
fires. 
See 
table,
“Extension 
Cord 
Specifications”,
on 
page 
13.
SYMBOLS
IMPOR
TANT
: Some 
of 
the 
following 
symbols 
may 
be 
used 
on 
your 
tool. 
Please
study 
them 
and 
learn 
their 
meaning. 
Proper 
interpretation 
of 
these 
symbols 
will
allow 
you 
to 
operate 
the 
tool 
better 
and 
safer
.
SYMBOL
NAME
EXPLANA
TION
V
Volts
Voltage 
(Potential)
A
Amperes
Current
Hz
Hertz
Frequency 
(Cycles 
per 
Second)
W
Watt
Power
Kg
Kilograms
Weight
Alternating 
Current
Type 
of 
Current
Direct 
Current
Type 
of 
Current
Alternating 
or 
Direct 
Current
Type 
of 
Current
Earthing 
Terminal
Grounding 
Terminal
Class 
II Construction
Denotes 
Double 
Insulation
min
Minutes
Time
s
Seconds
Time
!
Diameter
Size 
of 
Drill 
Bits, 
Grinding 
Wheels, 
etc.
No 
load 
speed
No-load 
Rotational 
Speed
.../min
Revolutions 
per 
Minute
Revolutions, 
Sur
face 
Speed, 
Strokes, 
etc. 
per 
Minute
1,2,3, 
…
Ring 
Selector 
Settings
Speed, 
Torque 
or 
Position 
Settings
4
13
3
10
7
5
6
1
11
12
2
98
8. 
Latches
9. 
Dust 
Container
10. 
Filter 
Bag 
11. 
Rubber 
Band
12. 
Filter 
Cage
13. 
Ball 
Float 
(Inside 
Filter 
Cage)  
						

							WET 
VACUUMING
•Remove motor housing by pulling out on the latch-
es located on either side of the dust container.
•Remove 
the 
filter 
bag.
•Place 
motor 
housing 
on 
top 
of 
the 
dust 
container
and 
press 
down 
until 
the 
latches 
pop 
into 
place.
•Insert 
hose 
into 
the 
vacuum 
port.
•Plug 
in power 
cord 
and 
switch 
power 
to 
ON.
When 
the 
dust 
container 
is full 
of 
liquid, 
the 
float 
ball
will 
rise 
to 
the 
top 
and 
automatically 
shut 
off 
the 
air
flow
. The 
sound 
of 
the 
motor 
will 
become 
more 
high
pitched 
as 
the 
suction 
ceases 
and 
the 
motor 
works
harder
. When 
this 
happens, 
dry off 
your 
hands 
and
feet 
and 
shut 
off 
the 
motor 
immediately
. LEA
VING
THE 
MOTOR 
RUNNING 
WHEN 
THE 
BALL 
IS 
IN 
THE
RAISED 
POSITION 
CAN 
DAMAGE 
THE 
WET/DR
Y
VACUUM/BLOWER.Empty 
dust 
container 
before 
continuing.
EMPTYING 
THE 
DUST 
CONT
AINER
Always 
unplug 
the 
power 
cord 
before 
emptying 
the 
dust
container 
to 
prevent 
injuries 
from 
accidental 
starting. 
•Remove 
motor 
housing 
by 
pulling 
out 
on 
the 
latches 
located 
on 
either 
side 
of
the 
dust 
container
. 
•ALWAYS 
dispose 
of 
container 
contents 
wisely
. Use 
proper 
waste 
receptacles. 
•Clean 
out 
dust 
container 
thoroughly
. 
•Replace 
filter 
bag.
•Snap 
motor 
housing 
back 
onto 
dust 
container
.
BLOWER 
USE
ALWAYS 
wear 
ANSI-approved 
safety 
glasses 
when 
using
blower
.Particles 
may 
fly 
up 
into 
eyes 
and 
cause 
permanent 
damage. 
Wear
hearing 
protection 
if using 
blower 
for 
extended 
periods. 
Dust 
masks 
are 
also 
recommended 
when 
blowing 
fine 
material.
OPERA
TING 
THE 
WET/DR
Y VACUUM/BLOWER 
Do 
not 
operate 
the 
Wet/Dr
y Vacuum/Blower 
in 
areas 
where 
flammable 
gases
or 
explosive 
dust 
are 
present.
This 
will 
reduce 
the 
risk 
of 
fire 
or 
explosion.
Do 
not 
vacuum 
flammable 
or 
combustible 
liquids 
or 
hot 
ashes.
To reduce 
the 
health 
hazards 
from 
vapors 
or 
dust, 
DO 
NOT
vacuum 
toxic 
materials.
DR
Y VACUUMING
•Remove 
motor 
housing 
by 
pulling 
out 
on 
the
latches 
located 
on 
either 
side 
of 
the 
dust
container
. 
•Make 
sure 
the 
filter 
bag 
is dry. A wet 
filter
bag 
will 
clog 
if used 
to 
vacuum 
dry material.
•Check 
that 
the 
filter 
bag 
is firmly 
attached 
to
the 
filter 
basket. 
Make 
sure 
the 
rubber 
band
is as 
close 
to 
the 
cover 
as 
possible. 
Gaps 
will
allow 
vacuumed 
material 
to 
blow 
back 
out
through 
the 
blower 
hole.
•Place 
motor 
housing 
on 
top 
of 
the 
dust 
container 
and 
press 
down 
until 
the 
latches 
pop 
into 
place.
9
•Insert 
hose 
into 
the 
vacuum 
port.
•Plug 
in power 
cord 
and 
switch
power 
to 
ON.
•When 
vacuuming 
large 
amounts
of 
debris 
or 
ver
y fine 
dust, 
empty
the 
dust 
containerand 
filter 
bag
frequently
.
•When 
vacuuming 
is completed,
turn 
the 
switch 
OFF 
and 
unplug
the 
power 
cord.  
						

							•Release 
filter 
bag 
by 
pulling 
rubber 
band 
out
around 
the 
black 
plastic 
posts. 
•Pull 
filter 
bag 
off 
filter 
cage. 
Clean 
or 
discard.
•Clean 
area 
around 
the 
top 
of 
the 
filter 
cage
where 
filter 
bag 
will 
be 
attached. 
Removing
stray 
dust 
particles 
will 
ensure 
a tighter 
fit.
•Push 
replacement 
filter 
onto 
filter 
cage. 
Make
sure 
bag 
reaches 
all 
the 
way 
to 
the 
lid.
•Work your way around the filter bag, carefully
releasing the rubber band. M
ake sure that the
bag is held securely and that there are no gaps.
STORAGEALWAYS 
empty 
dust 
container 
before 
storage. 
Wrap 
cord 
around 
the 
indentation 
at the 
bottom 
of
the 
motor 
housing. 
Attach 
one 
end 
of 
the 
hose 
to 
the 
blower 
port 
and
the 
other 
to 
the 
vacuum 
port. 
Store 
indoors 
in 
a closed 
box 
or 
covered 
with 
a
cloth.STORING 
THE 
CORD
Store 
the 
power 
cord 
by 
wrapping 
it around 
the
indentation 
at the 
bottom 
of 
the 
motor 
housing. 
ALWAYS 
fully 
uncoil 
power 
cord 
before 
use.12
•Clean 
out 
dust 
container 
so 
blower 
will
not 
spray 
dust 
into 
the 
air 
when 
activated.•Insert 
hose 
into 
blower 
port 
at the 
rear
of 
Wet/Dr
y Vacuum/Blower
.
•Plug 
in power 
cord 
and 
switch 
power
to 
ON.
•NEVER
point 
blower 
hose 
toward 
people 
or 
animals.
•Use 
blower 
to 
move 
dirt, 
sawdust,
leaves 
and 
other 
small 
debris 
away
from 
patios, 
garages 
and 
driveways.
•When 
blowing 
is completed, 
turn 
the 
switch 
off 
and 
unplug 
the 
power 
cord.
MAINTENANCE 
AND 
CLEANING
Before 
each 
use, 
make 
sure 
dust 
container 
is clean 
and 
empty
. Check 
filter 
bag 
for
holes 
or 
tears. 
Clean 
or 
replace 
if necessar
y.
Wipe 
motor 
housing 
with 
mild 
soap 
and 
water
. NEVER 
use 
solvents 
or 
harsh 
chemicals.Use 
warm 
water 
and 
mild 
soap 
to 
clean 
dust 
container 
thoroughly
. Dry with 
soft
cloth.DO 
NOT 
attempt 
to 
ser
vice 
the 
Wet/Dr
y Vacuum/Blower 
yourself.
Take 
the 
unit 
to
an 
authorized 
repair 
technician.
CLEANING 
AND 
REPLACING 
FIL
TER
ALWAYS 
unplug 
Wet/Dr
y Vacuum 
/Blower 
before 
clean-
ing 
or 
changing 
the 
filter 
bag.
NEVER 
remove 
filter 
cage. 
It is there 
to 
prevent 
injur
y.
Be 
careful 
not 
to 
tear 
the 
bag 
when 
changing 
or 
cleaning 
the 
filter
. NEVER 
use 
a fil-
ter 
bag 
with 
tears 
or 
holes 
in it. 
Torn 
bags 
will 
release 
a great 
deal 
of 
dust.
•Remove 
motor 
housing 
by 
pulling 
out 
on 
the 
latches 
located 
on 
either 
side 
of
the 
dust 
container
.
•Turn 
motor 
housing 
upside-down 
and 
balance 
on 
top 
of 
dust 
container
. 
11
•Keep 
rubber 
band 
as 
close 
to 
the 
lid 
as 
possible.•Turn 
motor 
housing 
over 
and 
snap 
back 
onto
dust 
container
.  
						

							SPECIFICA
TIONS
SPECIFICA
TIONS
Voltage
120V 
60 
Hz 
Peak 
Horsepower
1.5 
Holding 
Capacity
2.2 
Gallons
Flex 
Hose 
Dimensions
1 5/8 
Diameter
, 56 
3/4 
Long
Overall 
Dimensions
11 
1/4 
W, 14 
1/4L, 
14 
3/4 
H
Weight
Approx. 
7.0 
lbs
OTHER 
CONSUMER 
DO-IT
-YOURSELF 
(DIY) 
TOOLS
Alltrade 
offers 
a full 
range 
of 
Kawasaki™ 
tools 
that 
make 
DIY 
jobs 
easy
. If you 
would
like 
further 
information 
on 
the 
following 
products, 
please 
contact 
Alltrade 
Customer
Ser
vice 
Department 
at 1-800-590-3723. 
Cordless 
Drills/Screwdrivers
Impact 
Wrenches
SandersJigsawsCir
cular 
Saws
Angle 
Grinders
Reciprocating 
Saws
RoutersRotar
y Tools
Corded 
and 
Cordless 
Multi-Purpose 
Tools
Wide 
Range 
of 
Accessories 
and 
more
STORING 
THE 
HOSE
Attach 
one 
end 
of 
the 
hose 
to 
the 
blower port and the other to the 
vacuum 
port. 
This 
will 
keep 
the 
hose
safe 
and 
convenient.
ACCESSORIES
Use 
only 
accessories 
that 
are 
recommended 
by 
the 
manufacturer 
for 
your 
model.
Accessories 
that 
may 
be 
suitable 
for 
one 
tool 
may 
become 
hazardous 
when 
used 
on
another 
tool.
Always 
attach 
grounded 
(3-prong) 
extension 
cords 
to 
grounded 
(3-hole) 
outlets.
If you 
must 
use 
an 
extension 
cord, 
be 
sure 
that 
the 
gauge 
is large 
enough 
to carr
y
the 
amount 
of 
current 
necessar
y for 
your 
power 
tool.
If not, 
your 
tool 
may 
experi-
ence 
a loss 
of 
power
, excessive 
voltage 
drop 
or 
overheating. 
The 
smaller 
the 
gauge
number
, the 
heavier 
the 
cord 
(see 
table 
on 
next 
page).
RECOMMENDED 
SIZES 
OF 
EXTENSION 
CORDS 
120 
VOL
T AC 
60 
HZ 
TOOLS
TOOL 
CURRENT 
RA
TING
CONDUCTOR 
SIZE 
IN 
A.W
.G
AMPERE
10FT
.
25FT
.
50FT
.
100FT
.
3-6
18
18
18
18
6-8
18
18
18
16
8-10
18
18
18
14
10-12
16
16
14
14
12-16
14
12
12
-
16-20
12
12
12
-
13
14  
						

							be 
inspected 
and, 
at 
Alltrade’
s option, 
repaired 
and/or 
replaced 
free 
of 
charge 
if
found 
to 
be 
defective 
and 
subject 
to 
warranty
. Alltrade 
retains 
the 
sole 
discretion 
to 
determine 
whether 
any 
item 
or 
part 
is 
nonconforming 
and, 
if so, 
whether 
the 
item 
and/or 
part 
will 
be 
repaired 
and/or 
replaced. 
If the 
unit 
is 
repaired, 
new 
or
reconditioned 
replacement 
parts 
may 
be 
used. 
If 
Alltrade 
chooses 
to 
replace 
the 
product, 
it may 
replace 
it with 
a new 
or 
reconditioned 
one 
of 
the 
same 
or 
comparable 
design. 
The 
repaired 
or 
replaced 
unit 
will 
be 
warranted 
under 
the 
terms
of 
the 
remainder 
of 
the 
warranty 
period. 
Typically
, a defective 
product 
that 
is
returned 
within 
the 
first 
30 
days 
after 
the 
pur
chase 
date 
will 
be 
replaced; 
for 
items
returned 
after 
the 
first 
30 
days 
and 
within 
the 
warranty 
period, 
covered 
defective
parts 
not 
subject 
to 
normal 
wear 
and 
tear 
or 
other 
exclusions 
will 
be 
repaired 
or
replaced, 
at Alltrade’
s option. 
During 
the 
warranty 
period, 
Alltrade 
will 
be 
responsi-
ble 
for 
the 
return 
shipping 
charges. 
Alltrade’
s repair 
and/or 
replacement 
of 
any 
non-
conforming item and/or part thereof shall constitute fulfillment of all 
obligations 
to 
the 
pur
chaser
. Alltrade 
shall 
not 
be 
responsible 
or 
liable 
for 
any
expense, 
including 
freight 
charges, 
or 
repairs 
made 
outside 
Alltrade’
s facility
, unless
expressly 
agreed 
to 
by 
Alltrade 
in 
writing. 
Under 
no 
circumstances 
shall 
Alltrade
bear 
any 
responsibility 
for 
loss 
of 
the 
unit, 
loss 
of 
time 
or 
rental, 
inconvenience,
commer
cial 
loss 
or 
consequential 
damages.
ExclusionsThis 
warranty 
does 
not 
cover 
parts 
damaged 
due 
to 
normal 
wear
, abnormal 
conditions, 
misapplication, 
misuse, 
abuse, 
accidents, 
operation 
at 
other 
than 
recommended 
pressures 
or 
temperatures, 
improper 
storage 
or 
freight 
damage.
Parts 
damaged 
or 
worn 
by 
operation 
in 
dusty 
environments 
are 
not 
warranted.
Failure to follow recommended operating and maintenance procedures also 
voids 
warranty
.
This 
limited 
warranty 
does 
not 
apply 
to 
accessor
y 
items 
such 
as 
drill 
bits, 
screwdriving 
bits, 
circular 
saw 
blades, 
jigsaw 
blades, 
grinding 
wheels, 
sanding
sheets 
and 
other 
related 
items.
DAMAGE 
TO 
THE 
PRODUCT 
RESUL
TING 
FROM 
TAMPERING, 
ACCIDENT
, ABUSE,
NEGLIGENCE, 
FAILURE 
TO 
FOLLOW 
INSTRUCTIONS, 
UNAUTHORIZED 
REP
AIRS
OR 
ALTERA
TIONS, 
DAMAGE 
WHILE 
IN 
TRANSIT 
TO 
OUR 
SERVICE 
FACILITY
, 
USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES, 
3 YEAR 
LIMITED 
WARRANTY
Express 
and 
Exclusive 
Limited
Warranty 
to 
Original 
Retail 
Buyer
Alltrade 
Tools 
LLC 
(hereinafter 
Alltrade) 
expressly 
warrants 
to 
the 
original 
retail
pur
chaser 
of 
the 
accompanying 
KA
WASAKI™
power 
tool 
and 
no 
one 
else 
all 
parts
of 
the 
product 
(except
those 
parts 
referred 
to 
below 
which 
are 
specifically 
exclud-
ed 
from 
such 
warranty 
(see 
Exclusions)) 
to 
be 
free 
from 
defects 
in 
materials 
and
workmanship 
for 
a period 
of 
three 
years 
from 
original 
date 
of 
pur
chase,
except 
that
such 
warranty 
with 
regard 
to 
the 
batter
y shall 
be
for 
a period 
of 
two 
years 
from
original 
date 
of 
pur
chase,
unless 
the 
tool 
is 
used 
for 
commer
cial 
or 
rental 
purposes.SPECIAL 
WARRANTY 
NOTE 
FOR
COMMERCIAL 
OR 
RENT
AL 
USE:
The 
above 
warranty 
for
this 
Kawasaki™ 
power 
tool, 
including 
the 
batter
y, shall 
be 
effective 
for
only 
90 
days 
from 
the 
original 
date 
of 
pur
chase 
if 
this 
tool 
is 
used 
for 
any 
COMMERCIAL 
OR 
RENT
AL
PURPOSE.
The 
date 
of 
pur
chase 
shall 
be 
the 
date 
of 
shipment 
to 
the 
original 
pur
chaser
, or 
the
date 
the 
original 
pur
chaser 
took 
possession, 
custody 
or 
control 
of 
the 
product,
whichever occurred first.
This warranty shall be null and void if the product or any
component 
thereof 
is 
modified 
or
altered.
This 
warranty 
does 
not 
apply 
to 
any
other 
product 
and/or 
component 
thereof 
manufactured 
or 
distributed 
by 
Alltrade,
and 
does 
not 
apply 
to 
products 
and/or 
components 
thereof 
designed, 
manufactured
and/or 
assembled 
by 
others, 
for 
which 
Alltrade 
makes 
no 
warranties 
whatsoever
.
THERE 
ARE 
NO 
WARRANTIES 
WHICH 
EXTEND 
BEYOND 
THE 
DESCRIPTION 
ON
THE 
FACE 
HEREOF
.
Warranty 
Performance 
By 
pur
chasing 
the 
product, 
pur
chaser 
expressly 
acknowledges 
and 
agrees 
that 
their
sole 
and 
exclusive 
remedy 
under 
this 
warranty 
shall 
be 
strictly 
limited 
to 
the 
repair
or 
replacement 
of 
any 
covered 
nonconforming 
items 
or 
parts 
thereof 
provided 
that
any 
such 
nonconforming 
item 
and/or 
part 
is promptly 
returned 
to 
Alltrade’
s facility
postage 
pre-paid 
and 
insured 
(address: 
ALL
TRADE 
Warranty 
Claims 
& 
Repair
, 
1431 
Via 
Plata, 
Long 
Beach, 
CA 
90810, 
Attn: 
Customer 
Ser
vice 
#1-800-590-3723)
within 
the 
applicable 
warranty 
period, 
with 
a written 
request 
by 
pur
chaser 
that
Alltrade 
repair 
and/or 
replace 
the 
nonconforming 
item 
and/or 
part. 
We recommend
that 
you 
keep 
the 
original 
product 
packaging 
in the 
event 
you 
need 
to 
ship 
the 
unit.
We suggest 
the 
package 
be 
insured 
against 
loss 
or 
in 
transit 
damage. 
When 
sending 
your 
product 
include 
your 
name, 
address, 
phone 
number
, dated 
proof 
of 
pur
chase 
(or 
copy), 
and 
a statement 
about 
the 
nature 
of 
problem. 
Warranty 
coverage 
is 
conditioned 
upon 
pur
chaser 
furnishing 
Alltrade 
with 
adequate 
written
proof 
that 
they 
are 
the 
original 
pur
chaser 
and 
of 
the 
original 
pur
chase 
date. 
Parts
returned, 
freight 
prepaid 
and 
insured, 
to 
Alltrade’
s facility 
(see 
above 
address) 
will
15
16  
						

							Limitation 
Of 
Liability
IN 
NO 
EVENT 
SHALL 
ALL
TRADE 
AND/OR 
ITS 
REPRESENT
ATIVE(S) 
BE 
LIABLE 
FOR
INDIRECT
, INCIDENT
AL, 
SPECIAL 
AND/OR 
CONSEQUENTIAL 
DAMAGES 
OF 
ANY
KIND 
ARISING 
OUT 
OF 
OR 
RELA
TED 
TO, 
DIRECTL
Y OR 
INDIRECTL
Y, ANY 
BREACH
OF 
ANY 
PROVISION 
OF 
ANY 
AGREEMENT 
BETWEEN 
ALL
TRADE 
AND/OR 
ITS 
REPRESENTATIVE(S) AND PURCHASER, ANY WARRANTY HEREUNDER, 
AND/OR 
THE 
EXISTENCE, 
DESIGN, 
MANUF
ACTURE, 
PURCHASE, 
USE 
AND/OR
OPERA
TION 
OF 
ANY 
ITEM(S) 
SOLD 
HEREUNDER 
EVEN 
IF ALL
TRADE 
AND/OR 
ITS
REPRESENT
ATIVE(S) 
HAS 
BEEN 
ADVISED 
OF 
THE 
POSSIBILITY 
OF 
ANY 
SUCH
DAMAGES. 
IN 
NO 
EVENT
, WHETHER 
AS 
A RESUL
T OF 
A BREACH 
OF 
CONTRACT
,
WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL 
ALL
TRADE’S 
AND/OR 
ITS 
REPRESENT
ATIVE(S)’ 
LIABILITY 
EXCEED 
THE 
PRICE 
OF
THE 
PRODUCT
. ANY 
AND 
ALL 
LIABILITY 
CONNECTED 
WITH 
THE 
USE 
OF 
THIS 
PRODUCT 
SHALL 
TERMINA
TE 
UPON 
THE 
EXPIRA
TION 
OF 
THE 
WARRANTY
PERIODS 
SPECIFIED 
ABOVE.
Limitations 
on 
Warranty 
Disclaimers 
Some 
states 
do 
not 
allow 
limitations 
on 
how 
long 
an 
implied 
warranty 
lasts 
and 
some 
states 
do 
not 
allow 
the 
exclusion 
or 
limitation 
of 
the 
incidental 
or 
consequential 
damages, 
so 
part 
or 
all 
of 
the 
above 
limitations 
or 
exclusions 
may 
not
apply 
to 
you. 
This 
warranty 
gives 
you 
specific 
legal 
rights, 
and 
you 
may 
also 
have
other 
rights 
which 
var
y from 
state 
to 
state.
If your 
product 
is 
not 
covered 
by 
this 
warranty
, please 
call 
our 
Customer 
Ser
vice
Department 
toll 
free 
at 1-800-590-3723 
for 
general 
repair 
information 
and 
charges.
18
17
COMMERCIAL 
AND 
RENT
AL 
APPLICA
TIONS 
OR 
OTHER 
CAUSES 
UNRELA
TED 
TO
PROBLEMS 
WITH 
MA
TERIAL 
OR 
WORKMANSHIP 
ARE 
NOT 
COVERED 
BY 
THIS
WARRANTY
.
Alltrade 
will 
not 
be 
liable 
for 
the 
following: 
labor 
charges, 
loss 
or 
damage 
resulting
from improper operation, maintenance or repairs made by other persons; 
pre-delivery services such as assembly, oil or lubricants, and adjustment; 
maintenance 
ser
vices 
that 
are 
normally 
required 
to 
maintain 
the 
product.
The 
use 
of 
other 
than 
genuine 
Alltrade 
Repair 
Parts 
will 
void 
warranty
.
Warranty 
Disclaimers 
EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES, 
GUARANTIES AND/OR REPRESENTATIONS. EXCEPT FOR THE LIMITED WARRANTY
PROVIDED 
ABOVE, 
ALL 
OTHER 
EXPRESS 
WARRANTIES, 
GUARANTIES 
AND/OR
REPRESENT
ATIONS 
BY 
ALL
TRADE 
AND/OR 
ITS 
REPRESENT
ATIVE(S) 
REGARDING
THE 
DESIGN, 
MANUF
ACTURE, 
PURCHASE, 
USE 
AND/OR 
OPERA
TION 
OF 
THE
PRODUCT 
OR 
ANY 
COMPONENT 
THEREOF 
SOLD 
HEREUNDER, 
REGARDLESS 
OF
WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION,
WRITTEN 
OR 
ORAL, 
ARISES 
BY 
OPERA
TION 
OF 
LA
W 
AND/OR 
EQUITY 
AND/OR 
BY
ANY 
ACT 
OR 
OMISSION 
OF 
ALL
TRADE 
AND/OR 
ITS 
REPRESENT
ATIVE(S), 
OR 
THE
BUYER, 
ARE 
HEREBY 
EXPRESSL
Y EXCLUDED 
AND 
DISCLAIMED 
BY 
ALL
TRADE
AND/OR 
ITS 
REPRESENT
ATIVES. 
PURCHASER 
KNOWINGL
Y 
AND 
WILLINGL
Y
WAIVES 
ANY 
AND 
ALL 
SUCH 
WARRANTIES 
AND 
RIGHTS, 
CLAIMS 
AND/OR 
CAUSES 
OF 
ACTION 
ARISING 
THEREFROM 
OR 
BASED 
THEREON. 
PURCHASER’S
SOLE 
AND 
EXCLUSIVE 
REMEDY 
IS 
AS 
ST
ATED 
ABOVE.
EXCLUSION 
AND 
DISCLAIMER 
OF 
ALL 
IMPLIED 
WARRANTIES, 
INCLUDING 
THE
IMPLIED 
WARRANTIES 
OF 
MERCHANT
ABILITY 
AND 
FITNESS 
FOR 
A PARTICULAR
PURPOSE. 
NO 
WARRANTY
, ORAL 
OR 
WRITTEN, 
OTHER 
THAN 
THE 
ABOVE 
WARRANTY 
IS 
MADE 
WITH 
REGARD 
TO 
THIS 
PRODUCT
. ALL 
EXPRESS 
AND/OR
IMPLIED 
WARRANTIES, 
GUARANTIES 
AND/OR 
REPRESENT
ATIONS 
BY 
ALL
TRADE
AND/OR 
ITS 
REPRESENT
ATIVE(S) 
REGARDING 
THE 
DESIGN, 
MANUF
ACTURE,
PURCHASE, 
USE 
AND/OR 
OPERA
TION 
OF 
THE 
PRODUCT 
OR 
ANY 
COMPONENT
THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH WARRANTY,
GUARANTY AND/OR REPRESENTATION, WRITTEN OR ORAL, ARISES BY 
OPERA
TION 
OF 
LA
W 
AND/OR 
EQUITY 
AND/OR 
BY 
ANY 
ACT 
OR 
OMISSION 
OF
ALL
TRADE 
AND/OR 
ITS 
REPRESENT
ATIVE(S), 
OR 
THE 
PURCHASER, 
INCLUDING
BUT 
NOT 
LIMITED 
TO 
THE 
IMPLIED 
WARRANTY 
OF 
MERCHANT
ABILITY 
AND 
THE
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY EXPRESSLY
EXCLUDED 
AND 
DISCLAIMED 
BY 
ALL
TRADE 
AND/OR 
ITS 
REPRESENT
ATIVES.
PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH 
WARRANTIES 
AND 
RIGHTS, 
CLAIMS 
AND/OR 
CAUSES 
OF 
ACTION 
ARISING
THEREFROM OR BASED THEREON. PURCHASER’S SOLE AND EXCLUSIVE 
REMEDY 
IS 
AS 
ST
ATED 
ABOVE.