AllTrade Kawasaki 192V Cordless Worklight 840646 User Manual
Have a look at the manual AllTrade Kawasaki 192V Cordless Worklight 840646 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 102 AllTrade manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
SCREWDRIVING WHEN DRIVING FASTENERS: • Always start slowly and gradually increase the speed of the Drill. • Release the trigger when you feel the clutch slip. • Always keep the driver bit straight to prevent damage to the screw. • Hold the Drill with both hands to ensure control if the bit should stick or slip. • To prevent wood from splitting, drill pilot holes into the wood before driving in the screws. DRILLING METAL WHEN DRILLING HARD METALS: • Apply a lubricant, such as cutting oil, to the tip of the bit. • Start with a small hole then enlarge to the required size. Make sure the bit is actually cutting and not spinning in the hole as this will dull the edges of the bit. • Keep enough pressure on the bit to keep it drilling through the material. DRILLING MASONRY WHEN DRILLING MASONRY: • Masonry can be brittle so be careful not to apply too much pressure and crack the material. • Apply enough pressure to keep the bit cutting and not spinning in the hole as this will dull the edges of the bit. • Bricks and similar soft materials will require less pressure, concrete will require much more. DRILLING WOOD Use twist bits to drill holes in wood. Make sure the bits are sharp. Pull the bits out of the hole frequently to clear chips from the flutes as an overburdened bit may overheat. HINTS FOR OPTIMUM USE DRILLING: • Keep the right amount of pressure in a straight line with the drill bit. Too little and the bit will spin without cutting, too much and the motor may stall. 16 TORQUE SETTINGS To prevent damaging the tool or driving screw too deep into work piece, release the trigger when you feel the clutch slip. THE CONTROL RING ADJUSTS THE LEVEL OF TORQUE: • For light duty work, use lower settings. • For heavy duty work, use higher settings. PROPER SETTING FOR DRIVING SCREWS: 1. Set the ring on the lowest setting to begin. 2. Try tightening the first screw. If the drill drives smoothly, proceed with the next screw. 3. If the Drill’s clutch slips, increase the torque setting and try again until the Drill drives the screw without incident.HIGH / LOW SPEED (GEAR) SHIFTING FOR LOW SPEED SETTING: • Slide the switch on top of the Drill to Position 1 for high torque applications and driv- ing screws. FOR HIGH SPEED SETTING: • Slide the switch to Position 2 for light duty projects. 15 CONTROL RING HIGH SPEED LOW SPEED
Regularly clean the ventilation slots in your tool and charger using only a soft brush or dry cloth. Never open the Cordless Drill case, battery pack or charger.Do not attempt to repair the Cordless Drill, battery pack or charger yourself. Opening any of these parts will void your warranty. ACCESSORIES Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may become hazardous when used on another tool. Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets. If you must use an extension cord, be sure that the gauge is large enough to carry the amount of current necessary for your power tool.If not, your tool may experi- ence a loss of power, excessive voltage drop or overheating. The smaller the gauge number, the heavier the cord (see table on next page). RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLS TOOL CURRENT RATING CONDUCTOR SIZE IN A.W.GAMPERE 10FT. 25FT. 50FT. 100FT. 3-6 18 18 18 186-8 18 18 18 168-10 18 18 18 1410-12 16 16 14 1412-16 14 12 12 -16-20 12 12 12 - 18 • Just before the drill tip breaks though the other side of the work piece drill more slowly and decrease pressure on the tool. This will prevent stalling and leave a cleaner hole. • Use a block of wood to back up work pieces that may splinter. • Use spade bits when drilling large diameter holes in wood. • Use HSS drill bits when drilling in metal. • Use masonry bits when drilling in soft masonry. • Use a lubricant when drilling metals other than cast iron, aluminum, copper, and brass. • When drilling, start the hole slowly, allowing the bit to drill deep enough to prevent slipping at higher speeds. • Never try to start a stalled Drill by clicking the trigger switch “ON”and “OFF”. This may damage your tool. • To reduce jamming, always keep the Drill running when pulling the bit out of a finished hole. SCREWDRIVING: • Always use the correct type and size of screwdriver bit. • If screws are difficult to tighten, try applying a small amount of washing liquid or soap as a lubricant. • Always hold the tool and screwdriver bit in a straight line with the screw. MAINTENANCE AND CLEANING Always remove the battery pack before attempting cleaning or maintenance. This Cordless Drill is lubricated before it leaves the factory. This lubrication should last for the life of the tool. No further lubrication is required. Use only mild soap and a damp cloth to clean the tool.Never let any liquid get inside the casing. Never immerse any part of the tool in a liquid. Always keep the ventilation openings clear. Always clean the battery pack using only a dry cloth. Do not use liquids. Always unplug the charger before cleaning it. 17
SPECIAL WARRANTY NOTE TO CONTRACTORS AND COMMERCIAL USERS:This Kawasaki™ portable power tool is offered as a home use tool and carries a HOME USE WARRANTY. This tool is made for home use in the execution of projects and repairs in and around the home. Use of the tool for COMMERCIAL PURPOSES OR ON A JOBSITEis not covered under this warranty. The date of purchase shall be the date of shipment to the original purchaser, or the date the original purchaser took possession, custody or control of the product, whichever occurred first. This warranty shall be null and void if the product or any component thereof is modified, altered or used for any commercial purpose or on a jobsite. This warranty does not apply to any other product and/or component thereof manufactured or distributed by Alltrade, and does not apply to products and/or components thereof designed, manufactured and/or assembled by others, for which Alltrade makes no warranties whatsoever.THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. Warranty Performance By purchasing the product, purchaser expressly acknowledges and agrees that their sole and exclusive remedy under this warranty shall be strictly limited to the repair or replacement of any covered nonconforming items or parts thereof provided that any such nonconforming item and/or part is promptly returned to Alltrade’s facility postage pre-paid and insured (address: ALLTRADE Warranty Claims & Repair, 1431 Via Plata, Long Beach, CA 90810, Attn: Customer Service #1-800-590-3723) within the applicable warranty period, with a written request by purchaser that Alltrade repair and/or replace the nonconforming item and/or part. We recommend that you keep the original product packaging in the event you need to ship the unit. We suggest the package be insured against loss or in transit damage. When sending your product include your name, address, phone number, dated proof of purchase (or copy), and a statement about the nature of problem. Warranty coverage is conditioned upon purchaser furnishing Alltrade with adequate written proof that they are the original purchaser and of the original purchase date. Parts returned, freight prepaid and insured, to Alltrade’s facility (see above address) will be inspected and, at Alltrade’s option, repaired and/or replaced free of charge if found to be defective and subject to warranty. Alltrade retains the sole discretion to determine whether any item or part is nonconforming and, if so, whether the item and/or part will be repaired and/or replaced. If the unit is repaired, new or reconditioned replacement parts may be used. If Alltrade chooses to replace the product, it may replace it with a new or reconditioned one of the same or comparable design. The repaired or replaced unit will be warranted under the terms of the remainder of the warranty period. Typically, a defective product that is returned within the first 30 days after the purchase date will be replaced; for items returned after the first 30 days and within the warranty period, covered defective parts not subject to normal wear and tear or other exclusions will be repaired or replaced, at Alltrade’s option. During the warranty period, Alltrade will be responsi- ble for the return shipping charges. Alltrade’s repair and/or replacement of any non- SPECIFICATIONS SPECIFICATIONSVoltage 19.2V No Load Low Speed 0-400/min.No Load High Speed 0-1100/min.Torque Settings 24+1 DrillChuck Capacity Up to 10mm (3/8) Charger Input 120V 60HzCharging Time Approx. 3-5 hoursBattery Type Ni-Cad PROTECTING THE ENVIRONMENT BATTERIES Alltrade batteries can be recharged many times. At the end of their useful life, recycle batteries with due care for our environment. Ni-Cad and Ni-MH batteries are recyclable. Take them to your local recycling center or call 1-800-822-8837. Collected batteries will be recycled or disposed of properly. OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS Alltrade offers a full range of Kawasaki™ tools that make DIY jobs easy. If you would like further information on the following products, please contact Alltrade Customer Service Department at 1-800-590-3723. Cordless Drills/Screwdrivers Impact Wrenches Sanders Jigsaws Circular Saws Angle Grinders 2 YEAR LIMITED HOME USE WARRANTY Express and Exclusive Limited Home Use Warranty to Original Retail Buyer Alltrade Tools LLC (hereinafter Alltrade) expressly warrants to the original retail purchaser of the accompanying KAWASAKI™ portable power tool and no one else all parts of the product (except those parts referred to below which are specifically excluded from such warranty (see Exclusions)) to be free from defects in materials and workmanship for a period of two years from original date of purchase. 19Reciprocating Saws Routers Rotary Tools Corded and Cordless Multi-Purpose Tools Wide Range of Accessories and more
EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. NO WARRANTY, ORAL OR WRITTEN, OTHER THAN THE ABOVE WARRANTY IS MADE WITH REGARD TO THIS PRODUCT. ALL EXPRESS AND/OR IMPLIED WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS BY ALLTRADE AND/OR ITS REPRESENTATIVE(S) REGARDING THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION, WRITTEN OR ORAL, ARISES BY OPERATION OF LAW AND/OR EQUITY AND/OR BY ANY ACT OR OMISSION OF ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE PURCHASER, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE AND/OR ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS AND/OR CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON. PURCHASER’S SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE. Limitation Of Liability IN NO EVENT SHALL ALLTRADE AND/OR ITS REPRESENTATIVE(S) BE LIABLE FOR INDIRECT, INCIDENTAL, SPECIAL AND/OR CONSEQUENTIAL DAMAGES OF ANY KIND ARISING OUT OF OR RELATED TO, DIRECTLY OR INDIRECTLY, ANY BREACH OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND/OR ITS REPRESENTATIVE(S) AND PURCHASER, ANY WARRANTY HEREUNDER, AND/OR THE EXISTENCE, DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF ANY ITEM(S) SOLD HEREUNDER EVEN IF ALLTRADE AND/OR ITS REPRESENTATIVE(S) HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH DAMAGES. IN NO EVENT, WHETHER AS A RESULT OF A BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL ALLTRADE’S AND/OR ITS REPRESENTATIVE(S)’ LIABILITY EXCEED THE PRICE OF THE PRODUCT. ANY AND ALL LIABILITY CONNECTED WITH THE USE OF THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY PERIODS SPECIFIED ABOVE. Limitations on Warranty Disclaimers Some states do not allow limitations on how long an implied warranty lasts and some states do not allow the exclusion or limitation of the incidental or consequential damages, so part or all of the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. If your product is not covered by this warranty, please call our Customer Service Department toll free at 1-800-590-3723 for general repair information and charges. 22 conforming item and/or part thereof shall constitute fulfillment of all obligations to the purchaser. Alltrade shall not be responsible or liable for any expense, including freight charges, or repairs made outside Alltrade’s facility, unless expressly agreed to by Alltrade in writing. Under no circumstances shall Alltrade bear any responsibility for loss of the unit, loss of time or rental, inconvenience, commercial loss or consequential damages. Exclusions This warranty does not cover parts damaged due to normal wear, abnormal conditions, misapplication, misuse, abuse, accidents, operation at other than recommended pressures or temperatures, improper storage or freight damage. Parts damaged or worn by operation in dusty environments are not warranted. Failure to follow recommended operating and maintenance procedures also voids warranty. This limited warranty does not apply to accessory items such as drill bits, screwdriving bits, circular saw blades, jigsaw blades, grinding wheels, sanding sheets and other related items. DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING, ACCIDENT, ABUSE, NEGLIGENCE, FAILURE TO FOLLOW INSTRUCTIONS, UNAUTHORIZED REPAIRS OR ALTERATIONS, DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY, USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES, COMMERCIAL AND RENTAL APPLICATIONS OR OTHER CAUSES UNRELATED TO PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS WARRANTY. Alltrade will not be liable for the following: labor charges, loss or damage resulting from improper operation, maintenance or repairs made by other persons; pre-delivery services such as assembly, oil or lubricants, and adjustment; maintenance services that are normally required to maintain the product. The use of other than genuine Alltrade Repair Parts will void warranty. Warranty Disclaimers EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS. EXCEPT FOR THE LIMITED WARRANTY PROVIDED ABOVE, ALL OTHER EXPRESS WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS BY ALLTRADE AND/OR ITS REPRESENTATIVE(S) REGARDING THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION, WRITTEN OR ORAL, ARISES BY OPERATION OF LAW AND/OR EQUITY AND/OR BY ANY ACT OR OMISSION OF ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE BUYER, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE AND/OR ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS AND/OR CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON. PURCHASER’S SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE.