AllTrade Kawasaki 144V Cordless Impact Wrench 840062 User Manual

							COMPONENT
#840062-1HR
14.4V BATTERY-OPERATED 
IMPACT WRENCHINSTRUCTION MANUAL
FOR CUSTOMER SERVICE
POUR LE SERVICE APRÉS VENTE
OU DU CONSOMMATEUR
PARA EL SERVICIO
PARA EL CONSUMIDOR1-800-590-3723
Printed in China 
87-1904-60957
KAWASAKI™ IS A TRADEMARK LICENSED BY KAWASAKI™
MOTORS CORP., U.S.A., WHICH DOES NOT MANUFACTURE OR 
DISTRIBUTE THIS PRODUCT. CONSUMER INQUIRES SHOULD BE
DIRECTED TO:
©COPYRIGHT 2006 ALLTRADE TOOLS, LLC.
1431 VIA PLATA
LONG BEACH, CA 90810-1462 USA
840062 – 14.4V Green Cordless Impact Wrench_Rev 8/7/06
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION,
MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USE, READ CAREFULLY AND 
UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT LABELS. FAILURE TO DO
SO COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.
IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR ALLTRADE 
PRODUCT, DO NOT RETURN THIS PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER SERVICE
DEPARTMENT AT 1-800-590-3723. BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION 
AVAILABLE: MODEL No., DATE PURCHASED AND STORE LOCATION. AN ALLTRADE 
REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU WOULD LIKE TO MAKE
A SUGGESTION OR COMMENT, GIVE US A CALL OR EMAIL US AT: [email protected].
YOUR FEEDBACK IS VITAL TO US. 
						

							CONGRATULATIONS!
Thanks for choosing this product. At Alltrade, our aim is to provide you with quality
products at an affordable price, and we want you to be totally satisfied with your
product and our Customer Service. If any help and advice is needed, please 
contact us at 1-800-590-3723. Properly cared for, this tool will give you many 
years of satisfaction.
INTENDED USE
This tool is intended for consumer use only. Your charger and/or adapter has been
designed for charging batteries of the type approved and supplied with this tool.
GENERAL SAFETY RULES—FOR ALL BATTERY OPERATED TOOLS
READ AND UNDERSTAND ALL INSTRUCTIONS.Failure to
follow all instructions listed below may result in electric shock, fire and/or 
serious personal injury.
RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS
The safety instructions provided in this manual are not intended to cover all possible
conditions and practices that may occur when operating, maintaining and cleaning
power tools.
Always use common sense and pay particular attention to all the DANGER, 
WARNING, CAUTIONand NOTEstatements of this manual.
This is the safety alert symbol. It is used to alert
you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid
possible injury or death.
DANGERindicates an imminently hazardous 
situation which, if not avoided, will result in death
or serious injury.
WARNINGindicates a potentially hazardous 
situation which, if not avoided, could result in
death or serious injury.
2
TABLE OF CONTENTS
CONGRATULATIONS! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
INTENDED USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SECTION ONE
GENERAL SAFETY RULES—FOR ALL BATTERY OPERATED TOOLS  . . 2
RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS  . . . . . . . . 2-3
IMPORTANT SAFEGUARDS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
WORK AREA  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
ELECTRICAL SAFETY  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
PERSONAL SAFETY  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
TOOL USE AND CARE  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
SERVICE  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
SECTION TWO
SPECIFIC SAFETY RULES AND/OR SYMBOLS  . . . . . . . . . . . . . . . . . . . 6
SAFETY RULES FOR IMPACT WRENCHES  . . . . . . . . . . . . . . . . . . . 6-7
SYMBOLS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
SECTION THREE
FUNCTIONAL DESCRIPTION  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
BATTERY  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-12
REMOVING / ATTACHING BATTERY PACK  . . . . . . . . . . . . . . . . . . . 11
CHARGER  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
CHARGING BATTERY PACK  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
ASSEMBLY  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
INSTALLING / REMOVING SOCKET ON THE ANVIL  . . . . . . . . . . . . 13
OPERATING THE IMPACT WRENCH  . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-14
VARIABLE SPEED TRIGGER SWITCH . . . . . . . . . . . . . . . . . . . . . . . 14
FORWARD / REVERSE AND TRIGGER LOCK LEVER . . . . . . . . . . . . 14
SECTION FOUR
MAINTENANCE AND CLEANING  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
ACCESSORIES  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
PROTECTING THE ENVIRONMENT  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS  . . . . . . . . . . . . . . 16
SECTION FIVE
3 YEAR LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-20
1 
						

							WORK AREA
Keep your work area clean and well lit.Cluttered work benches and dark work
areas may cause accidents or injury.
Do not operate power tools in explosive areas, such as in the presence of 
flammable liquids, gases or dust. Power tools create sparks which may ignite
the dust or fumes.
Keep bystanders, children and visitors away while operating a power tool.
Distractions can cause you to lose control. 
ELECTRICAL SAFETY
Do not abuse the cord. Never use the cord to carry the tool. Keep the cord
away from heat, oil, sharp edges, or moving parts. Replace damaged cords
immediately.Damaged cords may create a fire.
A battery operated tool with integral batteries or a separate battery pack
must be recharged only with the specified charger for the battery.A charger
that may be suitable for one type of battery may create a risk of fire when used with
another battery.
Use battery operated tool only with specifically designatedbattery pack.Use of
any other batteries may create risk of fire.
4
CAUTIONindicates a potentially hazardous 
situation which, if not avoided, may result in
minor or moderate injury.
CAUTIONused without the safety alert symbol
indicates a potentially hazardous situation which,
if not avoided, may result in property damage.
NOTEprovides additional information that is useful
for proper use and maintenance of this tool. If a
NOTE is indicated make sure it is fully understood.
IMPORTANT SAFEGUARDS
People with electronic devices, such as pacemakers, should consult their
physician(s) before using this product. Operation of electrical equipment in
close proximity to a heart pacemaker could cause interference or failure of
the pacemaker.
WARNING:Some dust created by power sanding, sawing, grinding, drilling and
other construction activities contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints. 
• Crystalline silica from bricks and cement and other masonry products,
and arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such as dust masks that are
specially designed to filter out microscopic particles.
WARNING: Handling the power cord on corded products may expose you to
lead, a chemical known to the State of California to cause cancer and birth
defects or other reproductive harm.
Wash hands after handling.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
3 
						

							When battery pack is not in use, keep it away from other metal objects like:
paper clips, coins, keys, nails, screws, or other small metal objects that can
make a connection from one terminal to another. Shorting the battery termi-
nals together may cause sparks, burns or a fire.
Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained
tools with sharp cutting edge are less likely to bind and are easier to control. 
Check for misalignment or binding of moving parts, breakage of parts, and any
other condition that may affect the tool’s operation. If damaged, have the tool
serviced before using.Many accidents are caused by poorly maintained tools.
Use only accessories that are recommended by the manufacturer for your
model.Accessories that may be suitable for one tool may create a risk of injury
when used on another tool.
SERVICE
Tool service must be performed only by qualified repair personnel.Service or
maintenance by unqualified personnel may result in a risk of injury. 
When servicing a tool, use only identical replacement parts. Follow instructions
in the Maintenance section of this manual. Use of unauthorized parts or failure to
follow Maintenance Instructions may create a risk of shock or injury.
SPECIFIC SAFETY RULES AND/OR SYMBOLS
Hold tool by insulated gripping surfaces when perform-
ing an operation where the cutting tool may contact hidden wiring.Contact
with a “live” wire will also make exposed metal parts of the tool “live” and shock
the operator.SAFETY RULES FOR IMPACT WRENCHES
Always wear safety goggles or eye protection when using this tool. Use a
dust mask or respirator for applications which generate dust.
Do not grasp the tool or place your hands too close to the spinning chuck or
drill bit. Your hand may be lacerated or may cause injury.
Secure the material being worked on. Never hold it in your hand or across
your legs. Unstable support can cause loss of control and injury.
6
PERSONAL SAFETY
Stay alert, watch what you are doing, and use common sense when operat-
ing a power tool. Do not use tool while tired or under the influence of drugs,
alcohol or medication.A moment of inattention while operating power tools
may result in serious personal injury.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves away from moving parts.Loose clothes,
jewelry or long hair can be caught in moving parts. 
Avoid accidental starting. Be sure switch is in the locked or “OFF” position
before inserting battery pack. Carrying power tools with your finger on the
switch or inserting battery pack into a tool with the power switch “on” invites
accidents.
Remove adjusting keys or wrenches before turning the tool “ON”.
A wrench or a key that is left attached to a rotating part of the tool may result
in personal injury.
Do not overreach. Keep proper footing and balance at all times. Proper foot-
ing and balance enable better control of the tool in unexpected situations.
Use safety equipment. Always wear eye protection. Dust mask, non-skid safety
shoes, hard hat, or hearing protection must be used for appropriate conditions.TOOL USE AND CARE
Use clamps or other practical ways to secure and support the workpiece to a 
stable platform.Holding the work by hand or against your body is unstable and
may lead to loss of control.
Do not force tool. Use the correct tool for your application.The correct tool
will do the job better and safer at the rate for which it is designed.
Do not use the tool if the power switch does not turn it “ON” or “OFF”.A tool that
cannot be controlled with the switch is dangerous and must be repaired.
Disconnect battery pack from tool or place the switch in the locked or “OFF” posi-
tion before making any adjustments, changing accessories, or storing the tool.
Such preventative safety measures reduce the risk of starting the tool accidentally.
Store idle tools out of reach of children and other untrained persons.Tools
are dangerous in the hands of untrained users.
5 
						

							SYMBOLS
IMPORTANT: Some of the following symbols may be used on your tool. Please
study them and learn their meaning. Proper interpretation of these symbols will
allow you to operate the tool better and safer.
SYMBOL NAME EXPLANATION
V Volts Voltage (Potential)A Amperes CurrentHz Hertz Frequency (Cycles per Second)W Watt PowerKg Kilograms Weight
Alternating Current Type of CurrentDirect Current Type of CurrentAlternating or Direct Current Type of CurrentEarthing Terminal Grounding TerminalClass II Construction Denotes Double Insulation
min Minutes Times Seconds Time

Diameter Size of Drill Bits, 
Grinding Wheels, etc.
No load speed No-load Rotational Speed
.../min Revolutions per Minute Revolutions, Surface Speed, 
Strokes, etc. per Minute
1,2,3, … Ring Selector Settings Speed, Torque or Position Settings
8
Position yourself to avoid being caught between the tool or side handle and
walls or posts.Should the socket or bit become bound in the work, the reac-
tion torque of the tool could crush your hand or leg.
Check to see that keys and adjusting wrenches are removed from the
Cordless Impact Wrench before switching the tool “ON”.Keys or wrenches
can fly away at high velocity striking you or a bystander.
When using the Cordless Impact Wrench, always maintain a firm grip on the
tool with both hands.
Hold tool by insulated gripping surfaces when performing an operation
where the cutting tool may contact hidden wiring.Contact with a live wire
will also make exposed metal parts of the tool live and shock the operator.
Keep the handle of the Cordless Impact Wrench dry, clean, and free from oil
and grease.
Do not run the Cordless Impact Wrench while carrying it at your side.A spin-
ning socket or bit could become entangled with clothing and injury may result.
Disconnect the plug or remove the battery pack from tool and place the switch in the
locked or “OFF” position before making any assembly adjustments, changing acces-
sories, performing any inspection, maintenance or cleaning procedures. Such 
preventive safety measures reduce the risk of starting the tool accidentally.
Do not use the Cordless Impact Wrench if it has been damaged, left outdoors
in the rain, snow, wet or damp environments, or immersed in liquid.
Maintain labels and nameplates on the Cordless Impact Wrench.These carry
important information. If unreadable or missing, contact Alltrade for a replacement.
7 
						

							BATTERY
Before using battery pack, please read carefully all instruc-
tions and cautionarymarkings on battery pack, battery
charger and product using battery.
Do not incinerate the battery pack even if it is severely
damaged or is completely worn out.The battery pack can
explode. 
Do not carry battery packs in aprons, pockets, or tool boxes, product kit
boxes, drawers, etc. with loose metal objects.battery pack terminals could
be short circuited causing damage to the battery pack, severe burns or fire.
The battery pack is Nickel-Cadmium (Ni-Cad) and is considered to be a toxic
material by the Environmental Protection Agency.Before disposing of 
damaged or worn out Ni-Cad battery packs, check with your State
Environmental Protection Agency to find out about special restrictions on the
disposal of these battery packs, take them to your local recycling center for
proper disposal, or call 1-800-822-8837.
The battery is not fully charged. Before first use, the battery pack requires 
3-5 hours charge time to be fully charged. Subsequent recharging needs 1 hour
for the battery to be fully charged. 
Always switch to a fresh battery when tool performance begins to diminish.
Severe heat is most destructive to a battery; the more heat generated, the faster
the battery loses power. A battery that gets too hot can have a shortened life. 
Never over-discharge a battery by using the tool even after tool performance
has decreased.Do not attempt to discharge a tool’s battery by continuing to
pull on the tool trigger. When tool performance begins to diminish, stop the tool
and recharge the battery for optimal performance.
Charge battery pack at ambient temperatures between 50° F – 104° F. 
Store tool and battery pack in locations where temperatures will not exceed
120°F. This is important to prevent serious damage to the battery cells.
The battery pack should always be recharged when the Cordless Impact Wrench
begins to run slowly. 
When battery pack is not in use, keep it away from other metal objects such as
paper clips, coins, keys, nails, screws or other small metal objects that can
make a connection from one terminal to another.Shorting the battery terminals
together may cause sparks, burns, or fire.   
10
FUNCTIONAL DESCRIPTION.
CONTROLS AND COMPONENTS:
1. Variable Speed Trigger Switch
2. Forward/Reverse and Trigger Lock
Lever
3. Gear Enclosure
4. Release Buttons on Each Side
5. Charger
COMPONENT MODEL NUMBERCHARGER 690287BATTERY PACK 690292
9
6. LED Charging Indicators
7. Anvil
8. Comfort Rubber Grip
9. Snap Hook
10. Battery Pack 
8
9
5
1
2
103
7
4
6
® 
						

							CHARGING BATTERY PACK
CHARGE 
BATTERY PACK:
1. Plug the charger
into the nearest
120 volt electri-
cal outlet.
2. Make sure the
trigger on the
Cordless
Impact Wrench
is in the “OFF”
position and remove the
battery pack from the Cordless Impact Wrench.
3. Insert the battery pack into the charger. Be sure that the battery pack is 
fully seated in the charger. Do not force. 
4. The red indicator light should come “ON”indicating that the battery pack is in
a “Fast Charge” mode. If the green indicator light comes “ON”, then the battery
is already fully charged.
5. After approximately one hour of charging, the red indicator light should go
“OFF” and the green light should come “ON” indicating that the battery is fully
charged and the charger is now in a “Trickle Charge” mode.
6. The battery can be left in a “Trickle Charge” mode until ready to use.
IMPORTANT INFORMATION FOR RECHARGING HOT BATTERIES
When using your Cordless Impact Wrench continuously, the batteries in your bat-
tery pack will become hot. You should let a hot battery pack cool down for approxi-
mately 30 minutes before attempting to recharge. When the battery pack becomes 
discharged and is hot, the red light on the charger will flash. When the battery 
pack cools down, the red light will glow continuously to indicate fast charging
mode, 1-hour charge time.
This will occur when continuous use of your Cordless
Impact Wrench causes the battery pack to become hot. It does not occur
under normal circumstances.
12
REMOVING / ATTACHING BATTERY PACK
REMOVE BATTERY PACK:
1. Press both release 
buttons on either side 
of the Cordless Impact
Wrench to release the 
battery pack.
2. Pull battery pack free of
Cordless Impact Wrench.
ATTACH BATTERY PACK:
1. Align the raised portion of the
battery pack with the groove in 
the battery compartment of the 
Cordless Impact Wrench.
2. Press the battery pack into place. Make sure the latches
are securely fastened. Do not use the Cordless Impact
Wrench if the battery pack is not seated properly. 
CHARGER
Before using battery charger, please read carefully all
instructions and cautionary markings on battery charger, battery pack and
product using battery.
Use only the charger which accompanied your product or direct replacement as
listed in this manual. Do not substitute any other charger. Use only Alltrade
approved chargers with your product.
Do not disassemble charger.
Do not use charger if it has been damaged, left outdoors in the rain, snow, wet
or damp environments, or immersed in liquid.
The battery pack and charger heat during charging. Place the charger on a flat, 
non-flammable surface away from flammable materials with at least four inches of
clearance to allow proper air circulation around the charger and battery pack.
When the battery pack requires recharging, a 1 hour charge allows the tool to
operate at full power.A charging indicator light on the charger will illuminate to
show that charging is taking place. 
11
RELEASE BUTTON
BATTERY INDICATORHigh Med Low
BATTERY PACK
LED LIGHT
BATTERY
CHARGER
RELEASE BUTTON
(PRESS) 
						

							VARIABLE SPEED TRIGGER SWITCH
THIS TOOL IS CONTROLLED 
BY A TRIGGER SWITCH:
• The speed of the Cordless Impact
Wrench depends on the amount of
pressure you put on the trigger.
• The more pressure you apply, the
faster the Cordless Impact Wrench
will go.
• Release the pressure and the
Cordless Impact Wrench will slow
down. 
FORWARD / REVERSE AND TRIGGER LOCK LEVER
Be sure the trigger is released when changing the position of the lever.
Always store the tool in the“LOCKED/OFF”position.
Always check the direction of the Cordless Impact Wrenchs rotation before use.
TO SELECT THE DIRECTIONS 
OF ROTATION:
• To select forward Cordless Impact
Wrench rotation, press the trigger 
lock from left to right flat against the
Cordless Impact Wrench body.
• To select reverse, press the trigger 
lock lever in the opposite direction.
• The center position locks the tool.
14
ASSEMBLY
Be aware that this tool is always in an operating condition
because it does not have to be plugged into an electrical outlet.Always turn
the switch “OFF”and remove the battery pack before changing bits. 
INSTALLING / REMOVING SOCKET ON THE ANVIL
When removing the socket or bit from the tool, avoid 
contact with skin and use proper protective gloves when grasping the socket,
bit or accessory.Accessories may be hot after prolonged use.
When installing a socket, align the 
holes in the side of the socket with the 
dent pin. Press the socket on until the 
dent pin engages in the hole. To remove a
socket, depress the dent pin through the
hole using a small pointed object and pull 
the socket off.
OPERATING THE IMPACT WRENCH
Never tape the trigger switch down to provide continuous
high speed.The tool may fail under such conditions causing fire or 
personal injury.
13
TRIGGER
SWITCHTRIGGER
LOCK 
						

							SPECIFICATIONS
SPECIFICATIONS
Voltage 14.4V Speed 0-2500 rpmImpacts Per Minute 3000Maximum Torque 130 ft.lbs.Charger Input 120V  60HzCharging Time Approx. 1 HourBattery Type Ni-Cad
PROTECTING THE ENVIRONMENT
BATTERIES
Alltrade batteries can be recharged many times. At the end of their useful life, recy-
cle batteries with due care for our environment. 
Ni-Cad and Ni-MH batteries are recyclable. Take them to your local recycling center
or call 1-800-822-8837. Collected batteries will be recycled or disposed of properly.
OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS
Alltrade offers a full range of Kawasaki™ tools that make DIY jobs easy. If you would
like further information on the following products, please contact Alltrade Customer
Service Department at 1-800-590-3723. 
Cordless Drills/Screwdrivers
Impact Wrenches
Sanders
Jigsaws
Circular Saws
Angle Grinders
Reciprocating Saws
Routers
Rotary Tools
Corded and Cordless Multi-Purpose Tools
Wide Range of Accessories and more
MAINTENANCE AND CLEANING
Always remove the battery pack before attempting
cleaning or maintenance.
This Cordless Impact Wrench is lubricated before it
leaves the factory. This lubrication should last for the life of the tool. No 
further lubrication is required.
Use only mild soap and a damp cloth to clean the tool.Never let any liquid get
inside the casing. Never immerse any part of the tool in a liquid. Always keep the
ventilation openings clear.
Always clean the battery pack using only a dry cloth. Do not use liquids. 
Always unplug the charger before cleaning it.
Regularly clean the ventilation slots in your tool and charger using only a soft
brush or dry cloth.
Never open the Cordless Impact Wrench case, battery pack or charger.Do not
attempt to repair the Cordless Impact Wrench, battery pack or charger yourself.
Opening any of these parts will void your warranty.
ACCESSORIES
Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may become hazardous when used on
another tool.
Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets.
If you must use an extension cord, be sure that the gauge is large enough to carry
the amount of current necessary for your power tool.If not, your tool may 
experience a loss of power, excessive voltage drop or overheating. The smaller the
gauge number, the heavier the cord (see table below).
RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLS
TOOL CURRENT RATING CONDUCTOR SIZE IN A.W.G
AMPERE 10FT. 25FT. 50FT. 100FT.
3-6 18 18 18 186-8 18 18 18 168-10 18 18 18 1410-12 16 16 14 1412-16 14 12 12 -16-20 12 12 12 -
15 
						

							found to be defective and subject to warranty. Alltrade retains the sole discretion 
to determine whether any item or part is nonconforming and, if so, whether the 
item and/or part will be repaired and/or replaced. If the unit is repaired, new or
reconditioned replacement parts may be used. If Alltrade chooses to replace 
the product, it may replace it with a new or reconditioned one of the same or 
comparable design. The repaired or replaced unit will be warranted under the terms
of the remainder of the warranty period. Typically, a defective product that is
returned within the first 30 days after the purchase date will be replaced; for items
returned after the first 30 days and within the warranty period, covered defective
parts not subject to normal wear and tear or other exclusions will be repaired or
replaced, at Alltrade’s option. During the warranty period, Alltrade will be responsi-
ble for the return shipping charges. Alltrade’s repair and/or replacement of any non-
conforming item and/or part thereof shall constitute fulfillment of all 
obligations to the purchaser. Alltrade shall not be responsible or liable for any
expense, including freight charges, or repairs made outside Alltrade’s facility, unless
expressly agreed to by Alltrade in writing. Under no circumstances shall Alltrade
bear any responsibility for loss of the unit, loss of time or rental, inconvenience,
commercial loss or consequential damages.
Exclusions
This warranty does not cover parts damaged due to normal wear, abnormal 
conditions, misapplication, misuse, abuse, accidents, operation at other than 
recommended pressures or temperatures, improper storage or freight damage.
Parts damaged or worn by operation in dusty environments are not warranted.
Failure to follow recommended operating and maintenance procedures also 
voids warranty.
This limited warranty does not apply to accessory items such as drill bits, 
screwdriving bits, circular saw blades, jigsaw blades, grinding wheels, sanding
sheets and other related items.
DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING, ACCIDENT, ABUSE,
NEGLIGENCE, FAILURE TO FOLLOW INSTRUCTIONS, UNAUTHORIZED REPAIRS
OR ALTERATIONS, DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY, 
USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES, 
COMMERCIAL AND RENTAL APPLICATIONS OR OTHER CAUSES UNRELATED TO
PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS
WARRANTY.
Alltrade will not be liable for the following: labor charges, loss or damage resulting
from improper operation, maintenance or repairs made by other persons; 
pre-delivery services such as assembly, oil or lubricants, and adjustment; 
maintenance services that are normally required to maintain the product.
The use of other than genuine Alltrade Repair Parts will void warranty.
18
3 YEAR LIMITED WARRANTY
Express and Exclusive Limited Warranty to Original Retail Buyer
Alltrade Tools LLC (hereinafter Alltrade) expressly warrants to the original retail
purchaser of the accompanying KAWASAKI™ power tool and no one else all parts
of the product (except those parts referred to below which are specifically exclud-
ed from such warranty (see Exclusions)) to be free from defects in materials and
workmanship for a period of three years from original date of purchase, except that
such warranty with regard to the battery shall be for a period of two years from
original date of purchase, unless the tool is used for commercial or rental 
purposes.
SPECIAL WARRANTY NOTE FOR COMMERCIAL OR RENTAL USE:The above 
warranty for this Kawasaki™ power tool, including the battery, shall be effective for
only 90 days from the original date of purchase if this tool is used for any 
COMMERCIAL OR RENTAL PURPOSE.
The date of purchase shall be the date of shipment to the original purchaser, or the
date the original purchaser took possession, custody or control of the product,
whichever occurred first. This warranty shall be null and void if the product or any
component thereof is modified or altered. This warranty does not apply to any
other product and/or component thereof manufactured or distributed by Alltrade,
and does not apply to products and/or components thereof designed, manufactured
and/or assembled by others, for which Alltrade makes no warranties whatsoever.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON
THE FACE HEREOF.
Warranty Performance 
By purchasing the product, purchaser expressly acknowledges and agrees that their
sole and exclusive remedy under this warranty shall be strictly limited to the repair
or replacement of any covered nonconforming items or parts thereof provided that
any such nonconforming item and/or part is promptly returned to Alltrade’s facility
postage pre-paid and insured (address: ALLTRADE Warranty Claims & Repair, 
1431 Via Plata, Long Beach, CA 90810, Attn: Customer Service #1-800-590-3723)
within the applicable warranty period, with a written request by purchaser that
Alltrade repair and/or replace the nonconforming item and/or part. We recommend
that you keep the original product packaging in the event you need to ship the unit.
We suggest the package be insured against loss or in transit damage. When 
sending your product include your name, address, phone number, dated proof 
of purchase (or copy), and a statement about the nature of problem. Warranty 
coverage is conditioned upon purchaser furnishing Alltrade with adequate written
proof that they are the original purchaser and of the original purchase date. Parts
returned, freight prepaid and insured, to Alltrade’s facility (see above address) will
be inspected and, at Alltrade’s option, repaired and/or replaced free of charge if
17