AllTrade Kawasaki 13in Drill Press 840139 User Manual

MODEL #840139
13 
DRILL 
PRESS 
INSTRUCTION 
MANUAL
FOR 
CUSTOMER 
SERVICE
POUR 
LE SERVICE 
APRÉS 
VENTE
OU 
DU 
CONSOMMATEUR
PARA 
EL SERVICIO
PARA 
EL CONSUMIDOR
1-800-590-3723
Printed 
in China 
87-1904-60957
KAWASAKI™
IS A TRADEMARK 
LICENSED 
BY KAWASAKI™
MOTORS 
CORP
., U.S.A., 
WHICH 
DOES 
NOT 
MANUF
ACTURE 
OR 
DISTRIBUTE 
THIS 
PRODUCT
. CONSUMER 
INQUIRES 
SHOULD 
BE
DIRECTED 
TO:
©COPYRIGHT 
2006 
ALLTRADE 
TOOLS, 
LLC.
1431 
VIA PLATA
LONG 
BEACH, 
CA 90810-1462 
USA
840139 
– 13Drill...

INSER
TING 
LASER 
BA
TTERIES
 . . . . . . . . . . . . . . . . . . . . . . . . . . .
31
SECTION 
FOUR
MAINTENANCE 
AND 
CLEANING
 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
31
TROUBLE 
SHOOTING
 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33
ACCESSORIES
 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33
SPECIFICA
TIONS
 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
34
OTHER...

GENERAL 
SAFETY 
RULES 
– FOR 
ALL 
ELECTRIC 
POWER 
TOOLS
READ 
AND 
UNDERST
AND 
ALL 
INSTRUCTIONS.
Failure 
to
follow 
all 
instructions 
listed 
below 
may 
result 
in 
electric 
shock, 
fire 
and/or 
serious 
personal 
injur
y.
1.
KEEP 
GUARDS 
IN 
PLACE 
AND 
IN 
WORKING 
ORDER.
2.
REMOVE 
ADJUSTING 
KEYS 
AND 
WRENCHES.
Form 
a habit 
of 
checking 
to 
see
that 
keys 
and 
adjusting 
wrenches 
are 
removed 
from 
the 
tool 
before 
turning 
it
on.
3.
KEEP 
WORK 
AREA 
CLEAN.
Cluttered 
areas 
and...

This 
drill 
press 
is equipped 
with 
a grounded 
3-wire 
power 
cord 
with 
a 3-prong 
plug.
If the 
power 
cord 
will 
not 
fit 
into 
the 
wall 
plug, 
an 
approved 
adapter 
can 
be 
used 
as
long 
as 
it is connected 
to 
the 
center 
screw 
in 
the 
wall 
plate. 
See 
Figure 
1 and 
the
steps 
below 
to 
use 
an 
AC 
grounding 
adapter:
1.Remove 
the 
cover 
plate 
mounting 
screw
.
2.Insert 
the 
AC 
grounding 
adapter 
into 
the 
bottom 
receptacle 
so 
the 
green
grounding 
lug 
fits 
over 
the...

9.
USE 
ONL
Y DRILL 
BITS, 
SANDING 
DRUMS, 
AND 
OTHER 
ACCESSORIES
that
are 
designed 
for 
the 
various 
speeds 
of 
this 
drill 
press. 
The 
drill 
bits, 
sanding
drums 
and 
other 
accessories 
should 
have 
a shank 
size 
1/2 
OR 
SMALLER.
Unsuitable 
drill 
bits 
can 
break 
without 
warning 
throwing 
fragments 
outward 
at
high 
speeds 
possibly 
causing 
severe 
injuries. 
Contact 
Alltrade 
Customer
Ser
vice 
at 1-800-423-3598 
(toll 
free) 
for 
authorized 
drill 
bit 
specifications.
10....

30.
ADDITIONAL 
INFORMA
TION
about 
the 
proper 
use 
of 
bench-mounted 
drill
presses 
is available 
from 
the 
Power 
Tool 
Institute, 
1300 
Sumner 
Avenue,
Cleveland, 
OH 
44115-2851 
(www
.powertoolinstitute.com). 
Information 
is also
available 
from 
the 
National 
Safety 
Council, 
1121 
Spring 
Lake 
Drive, 
Itasca, 
IL
60143-3201. 
Additionally
, you 
can 
refer 
to 
the 
American 
National 
Standards
Institute 
(ANSI) 
01.1 
Safety 
Requirements 
for 
Woodworking 
Machines 
and 
the
U.S....

FUNCTIONAL 
DESCRIPTION
CONTROLS 
AND 
COMPONENTS:
1. 
Column 
Base
2. 
Column 
Assembly
3. 
Column
4. 
Column 
Rack
5. 
Table 
Crank
6. 
Table 
Support
7. 
Table 
Crank 
Assembly
8. 
Table
9. 
Vise
10. 
Vise 
mtg 
Hardware
11. 
Knob 
(and 
mtg 
Hardware)
12. 
Collar
ASSEMBL
Y
DO 
NOT 
connect 
the 
power 
cord 
to 
the 
AC 
receptacle
until 
the 
drill 
press 
is 
completely 
assembled 
and 
that 
all 
cutting 
tools 
are
securely 
locked 
in 
the 
chuck.
TOOLS 
REQUIRED 
FOR 
ASSEMBL
Y
The 
tools,...

To minimize 
crank 
handle 
backlash, 
tighten 
the 
support
lock, 
rotate 
the 
elevation 
worm 
shaft 
clockwise, 
assemble 
the 
crank 
tightly
against 
the 
table 
support 
and 
tighten 
setscrew
.
11.
Check 
column 
collar 
for 
proper
adjustment.
12.
Collar 
should 
not 
be 
aligned 
on 
the
column.
13.
Position 
rack 
so 
it will 
slide 
freely 
in
the 
collar 
when 
rotated 
360 
(around
column 
table).
14.
When 
re-adjusting, 
only 
tighten 
col-
lar 
setscrew 
tight 
enough 
to 
hold 
it...

6.Install 
the 
setscrews 
in the 
holes 
on 
the
right 
side 
of 
the 
head 
assembly
.
7.Using 
a 5mm 
“L” 
hex 
wrench 
(located 
in
the 
loose 
parts 
box) 
securely 
tighten 
the
setscrews.
INST
ALLING 
BEL
T GUARD 
KNOB
To avoid possible injury, always keep the belt guard closed
during drill press operation. Failure to do so could result in serous injury.
1.Remove 
the 
belt 
guard 
knob 
and 
5mm 
X
12mm 
pan 
head 
screw 
from 
the 
loose 
parts
bag.2.Open 
the 
belt 
guard 
and 
install 
the...

18
17
ADJUSTING 
THE 
DRIVE 
PULLEYS
The 
drive 
pulleys 
on 
the 
spindle 
shaft 
and 
the 
motor
shaft 
may 
loosen 
during 
shipment. 
It is 
crucial 
that 
these 
pulleys 
are 
the
same 
height 
on 
their 
respective 
shafts. 
Failure 
to 
square 
these 
pulleys 
could
result 
in 
premature 
belt 
wear 
or 
damage 
to 
the 
motor 
and 
spindle 
bearings
or 
both.
1.Lay 
a straightedge 
across 
the 
tops 
of 
the 
three
pulleys. 
If properly 
adjusted, 
they 
should 
all
touch 
the 
straightedge....