AllTrade Kawasaki 13in Drill Press 840091 User Manual

SQUARING 
THE 
WORKT
ABLE
The 
combination 
square 
must 
be 
“true” 
when 
used 
to
square 
the 
worktable. 
See 
Tools 
Required 
for 
Assembly
. This 
is essential 
in
order 
to 
do 
precision 
drilling.
1.Insert 
a straight, 
ground 
steel 
rod, 
approxi-
mately 
3 
long 
(not 
included) 
into 
the 
drill
check 
and 
tighten.
2.Raise 
the 
table 
to 
working 
height.
3.Place 
the 
combination 
square 
on 
the 
table
sur
face 
with 
the 
ruler 
portion 
setting
beside 
the 
ground 
rod. 
There 
should...

NEVER 
OPERA
TE 
LASER 
IF 
THE 
UNIT 
IS 
DEFECTIVE 
OR 
THE 
COVER 
OR 
SEAL
IS 
DAMAGED.
DO 
NOT 
SERVICE 
LASER.
The 
laser 
unit 
must 
be 
returned 
to 
the 
factor
y for 
any
ser
vice 
or 
repair
. Ser
vice 
or 
repair 
must 
be 
handled 
by 
authorized 
factor
y
trained 
technicians.
Do 
not 
open 
the 
laser 
unit 
except 
to 
change 
batteries.
REMOVE 
BA
TTERIES 
IF 
THE 
LEVEL 
IS 
TO 
BE 
STORED 
FOR 
ANY 
LENGTH 
OF
TIME.
Batteries 
may 
leak 
and 
damage 
the 
laser 
if it is stored 
idle...

It is 
recommended 
that 
an 
approved 
ANSI 
full-face 
shield, 
that 
is 
impact
resistant, 
be 
worn 
during 
all 
drill 
press 
operations. 
Should 
the 
full-face
shield 
not 
be 
available, 
approved 
ANSI 
safety 
glasses 
with 
impact 
resistant
lenses 
and 
side 
shields 
MUST 
be 
used 
as 
a substitute. 
DO 
NOT 
use 
normal
glasses. 
If prescription 
glasses 
are 
necessar
y, wear 
ANSI 
approved 
goggles
that 
will 
cover 
the 
glasses 
and 
protect 
the 
eyes 
on 
all 
sides. 
Safety...

9.Grasp 
the 
feed 
handles 
and 
rotate 
them 
toward 
the 
front 
of 
the 
drill 
press 
low-
ering 
the 
drill 
bit 
onto 
the 
workpiece. 
This 
step 
is necessar
y to 
ensure 
the 
hole
will 
be 
where 
it is intended. 
Make 
any 
adjustments 
necessar
y.
10.
Plug 
the 
drill 
press 
power 
cord 
into 
the 
AC 
power 
sour
ce. 
Insert 
the 
YELLOW
key 
into 
the 
ON/OFF 
switch.ADJUSTING 
THE 
TABLE 
HEIGHT
Turn 
the 
drill 
press 
ON/OFF 
switch 
to 
the 
OFF 
position
and 
disconnect 
the 
AC...

SETTING 
THE 
DRILLING 
DEPTH 
ADJUSTMENT
Turn the drill press ON/OFF switch to the OFF position and
disconnect the AC power to prevent drill press from accidentally turning on.
The 
drilling 
depth 
adjustment 
is used 
when 
more 
than 
one 
hole 
is to 
be 
drilled 
to
exactly 
the 
same 
depth 
(i.e. 
drilling 
holes 
for 
spindles 
in a handrail).
1.Locate 
the 
depth 
gauge 
and 
pointer 
(on 
the 
inner 
portion 
of 
the 
feed 
handle
hub).2.Loosen 
the 
lock 
screw 
(located 
next 
to 
the 
depth...

DRILLING 
 THROUGH 
 WOOD:
1.Position 
the 
workpiece 
so 
that 
the 
hole 
to 
be 
drilled 
is over 
the 
center 
hole 
on
the 
worktable.
2.Place 
a piece 
of 
scrap 
material 
under 
the 
workpiece 
to 
prevent 
“splintering” 
on
the 
bottom 
side 
of 
the 
workpiece.
3.Clamp 
BOTH 
the 
workpiece 
and 
the 
scrap 
material 
to 
the 
worktable.
4.Select 
the 
proper 
speed 
for 
the 
workpiece 
material 
and 
make 
any 
adjustments
necessar
y to 
the 
drive 
belts. 
5.Insert 
the 
Yellow 
plastic 
key...

TROUBLE
PROBABLE 
CAUSE
SOLUTION
When 
drilling 
metal, 
it is 
a good 
practice 
to 
keep 
the
workpiece 
lubricated. 
This 
prevents 
galling 
and 
eventual 
seizing 
of 
the 
drill
bit. 
Some 
drill 
bit 
models 
have 
accessories 
that 
automatically 
lubricate 
the
metal 
workpiece. 
Call 
Alltrade 
Customer 
Ser
vice 
at 
1-800-590-3723 
to 
see 
if
a lubricating 
accessor
y is available 
for 
this 
particular 
drill 
press.
6.Slowly 
reverse 
the 
feed 
handles 
until 
the 
drill 
bit 
has 
been...

SPECIFICA
TIONS
SPECIFICA
TIONS
Voltage
120V 
60 
Hz 
Rated 
Current
7.8 
A
No-Load 
Speed 
(motor)
1700 
RPM
Max. 
Distance 
From 
Spindle 
Axis 
To Sur
face 
Of 
Column:
7 3/4 
(197mm) 
Max. 
Distance 
From 
Spindle 
End 
To Sur
face 
Of 
Table:
26 
1/8 
(664mm)
Spindle 
Travel: 
3 3/8 
(86mm)
Chuck 
Capacity
5/8 
(16mm)
Range 
of 
Spindle 
Speeds
240-3200 
RPM 
Laser 
Beam
Class 
II, 
Diode 
Laser
Average 
Radiant 
Power 
1mw
Laser 
Beam 
Wavelength
650nm
OTHER 
CONSUMER 
DO-IT
-YOURSELF 
(DIY)...

found 
to 
be 
defective 
and 
subject 
to 
warranty
. Alltrade 
retains 
the 
sole 
discretion 
to 
determine 
whether 
any 
item 
or 
part 
is 
nonconforming 
and, 
if so, 
whether 
the 
item 
and/or 
part 
will 
be 
repaired 
and/or 
replaced. 
If the 
unit 
is 
repaired, 
new 
or
reconditioned 
replacement 
parts 
may 
be 
used. 
If 
Alltrade 
chooses 
to 
replace 
the 
product, 
it may 
replace 
it with 
a new 
or 
reconditioned 
one 
of 
the 
same 
or 
comparable 
design. 
The 
repaired 
or...

REPRESENT
ATIVE(S) 
HAS 
BEEN 
ADVISED 
OF 
THE 
POSSIBILITY 
OF 
ANY 
SUCH
DAMAGES. 
IN 
NO 
EVENT
, WHETHER 
AS 
A RESUL
T OF 
A BREACH 
OF 
CONTRACT
,
WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL 
ALL
TRADE’S 
AND/OR 
ITS 
REPRESENT
ATIVE(S)’ 
LIABILITY 
EXCEED 
THE 
PRICE 
OF
THE 
PRODUCT
. ANY 
AND 
ALL 
LIABILITY 
CONNECTED 
WITH 
THE 
USE 
OF 
THIS 
PRODUCT 
SHALL 
TERMINA
TE 
UPON 
THE 
EXPIRA
TION 
OF 
THE 
WARRANTY
PERIODS 
SPECIFIED 
ABOVE.
Limitations 
on 
Warranty 
Disclaimers...