AllTrade Kawasaki 12in AC Impact Wrench 840051 User Manual

							DANGERindicates an imminently hazardous 
situation which, if not avoided, will result in death
or serious injury.
WARNINGindicates a potentially hazardous 
situation which, if not avoided, could result in
death or serious injury.
CAUTIONindicates a potentially hazardous 
situation which, if not avoided, may result in
minor or moderate injury.
CAUTIONused without the safety alert symbol
indicates a potentially hazardous situation which,
if not avoided, may result in property damage.
NOTEprovides additional information that is useful
for proper use and maintenance of this tool. If a
NOTE is indicated make sure it is fully understood.
IMPORTANT SAFEGUARDS
People with electronic devices, such as pacemakers, should consult their
physician(s) before using this product. Operation of electrical equipment in
close proximity to a heart pacemaker could cause interference or failure of
the pacemaker.
WARNING:Some dust created by power sanding, sawing, grinding, drilling and
other construction activities contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints. 
• Crystalline silica from bricks and cement and other masonry products,
and arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such as dust masks that are
specially designed to filter out microscopic particles.
WARNING: Handling the power cord on corded products may expose you to
lead, a chemical known to the State of California to cause cancer and birth
defects or other reproductive harm.
Wash hands after handling.
WORK AREA
Keep your work area clean and well lit.Cluttered work benches and dark work
areas may cause accidents or injury.
Do not operate power tools in explosive areas, such as in the presence of 
flammable liquids, gases or dust. Power tools create sparks which may ignite
the dust or fumes.
Keep bystanders, children and visitors away while operating a power tool.
Distractions can cause you to lose control. 
ELECTRICAL SAFETY
Do not abuse the cord. Never use the cord to carry the tool, pulling or unplug-
ging the power tool. Keep the cord away from heat, oil, sharp edges, or mov-
ing parts. Replace damaged cords immediately.Damaged cords may create
a fire.
Damaged or entangled cords increase the risk of electric shock.
A battery operated tool with integral batteries or a separate battery pack
must be recharged only with the specified charger for the battery.A charger
that may be suitable for one type of battery may create a risk of fire when used with
another battery.
Use battery operated tool only with specifically designatedbattery pack.Use of
any other batteries may create risk of fire.
Power tool plugs must match the outlet.Never modify the plug in any way. Do
not use any adapter plugs with grounded power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
Avoid body contact with grounded surfaces such as pipes, radiators, ranges
and refrigerators.There is an increased risk of electric shock if your body is
grounded.
Do not expose power tools to rain or wet conditions.Water entering a power
tool will increase the risk of electric shock.
When operating a power tool outdoors, use an extension cord suitable for 
outdoor use.Use of a cord suitable for outdoor use reduces the risk of electric
shock.
4 
						

							Recharge only with the charger specified by the manufacturer.A charger that
is suitable for one type of battery pack may create a risk of fire when used with
another battery pack.
Use power tools only with specifically designated battery packs.Use of any
other battery packs may create a risk of injury and fire.
When battery pack is not in use, keep it away from other metal objects like
paper clips, coins, keys, nails, screws, or other small metal objects that can
make a connection from one terminal to another.Shorting the battery termi-
nals together may cause burns or a fire.
Under abusive conditions, liquid may be ejected from the battery, avoid con-
tact.If contact accidentally occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the battery may cause irrita-
tion or burns.
Store idle tools out of reach of children and other untrained persons.Tools
are dangerous in the hands of untrained users.
When battery pack is not in use, keep it away from other metal objects like:
paper clips, coins, keys, nails, screws, or other small metal objects that can
make a connection from one terminal to another. Shorting the battery termi-
nals together may cause sparks, burns or a fire.
Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained
tools with sharp cutting edge are less likely to bind and are easier to control.
Check for misalignment or binding of moving parts, breakage of parts, and any
other condition that may affect the tool’s operation. If damaged, have the tool
serviced before using.Many accidents are caused by poorly maintained tools.
Use only accessories that are recommended by the manufacturer for your
model.Accessories that may be suitable for one tool may create a risk of injury
when used on another tool.
SERVICE
Tool service must be performed only by qualified repair personnel.Service
or maintenance by unqualified personnel may result in a risk of injury. 
When servicing a tool, use only identical replacement parts. This will ensure
that the safety of the power tool is maintained.Follow instructions in the
Maintenance section of this manual. Use of unauthorized parts or failure to fol-
low Maintenance Instructions may create a risk of shock or injury.
5
PERSONAL SAFETY
Stay alert, watch what you are doing, and use common sense when operat-
ing a power tool. Do not use tool while tired or under the influence of drugs,
alcohol or medication.A moment of inattention while operating power tools
may result in serious personal injury.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves away from moving parts.Loose clothes,
jewelry or long hair can be caught in moving parts. 
Avoid accidental starting. Be sure switch is in the locked or “OFF” position before
inserting battery pack. Carrying power tools with your finger on the switch or insert-
ing battery pack into a tool with the power switch “ON”invites accidents.
Remove adjusting keys or wrenches before turning the tool “ON”.A wrench or a
key that is left attached to a rotating part of the tool may result in personal injury.
Do not overreach. Keep proper footing and balance at all times. Proper foot-
ing and balance enable better control of the tool in unexpected situations.
Use safety equipment. Always wear eye protection. Dust mask, non-skid safe-
ty shoes, hard hat, or hearing protection must be used for appropriate conditions.
If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used.Use of these
devices can reduce dust-related hazards.
TOOL USE AND CARE
Use clamps or other practical ways to secure and support the workpiece to a 
stable platform.Holding the work by hand or against your body is unstable and
may lead to loss of control.
Do not force tool. Use the correct tool for your application.The correct tool
will do the job better and safer at the rate for which it is designed.
Do not use the tool if the power switch does not turn it “ON” or “OFF”.A tool
that cannot be controlled with the switch is dangerous and must be repaired.
Disconnect battery pack from tool or place the switch in the locked or “OFF”
position before making any adjustments, changing accessories, or storing
the tool.Such preventative safety measures reduce the risk of starting the tool
accidentally. 
						

							SYMBOLS
IMPORTANT: Some of the following symbols may be used on your tool. Please
study them and learn their meaning. Proper interpretation of these symbols will
allow you to operate the tool better and safer.SYMBOL NAME EXPLANATION
V Volts Voltage (Potential)A Amperes CurrentHz Hertz Frequency (Cycles per Second)W Watt PowerKg Kilograms Weight
Alternating Current Type of CurrentDirect Current Type of CurrentAlternating or Direct Current Type of CurrentEarthing Terminal Grounding TerminalClass II Construction Denotes Double Insulation
min Minutes Times Seconds Time

Diameter Size of Drill Bits, 
Grinding Wheels, etc.
No load speed No-load Rotational Speed
.../min Revolutions per Minute Revolutions, Surface Speed, 
Strokes, etc. per Minute
1,2,3, … Ring Selector Settings Speed, Torque or Position Settings
8
SPECIFIC SAFETY RULES AND/OR SYMBOLS
Hold tool by insulated gripping surfaces when per-
forming an operation where the cutting tool may contact hidden wiring.
Contact with a “live” wire will also make exposed metal parts of the tool
“live” and shock the operator.
SAFETY RULES FOR CORDLESS DRILL / DRIVERS
Always wear safety goggles or eye protection when using this tool.Use a
dust mask or respirator for applications which generate dust. 
Do not grasp the tool or place your hands too close to the spinning chuck or
drill bit. Your hand may be lacerated or may cause injury.
Secure the material being worked on. Never hold it in your hand or across
your legs. Unstable support can cause loss of control and injury.
Position yourself to avoid being caught between the tool or side handle and
walls or posts.Should the socket or bit become bound in the work, the reac-
tion torque of the tool could crush your hand or leg.
Check to see that keys and adjusting wrenches are removed from the
Cordless Drill before switching the tool “ON”.Keys or wrenches can fly away
at high velocity striking you or a bystander.
When using the Cordless Drill, always maintain a firm grip on the tool with
both hands.
Hold tool by insulated gripping surfaces when performing an operation
where the cutting tool may contact hidden wiring.Contact with a live wire
will also make exposed metal parts of the tool live and shock the operator.
Keep the handle of the Cordless Drill dry, clean, and free from oil and grease.
Do not run the Cordless Drill while carrying it at your side.A spinning sock-
et or bit could become entangled with clothing and injury may result.
Disconnect the plug or remove the battery pack from tool and place the switch in
the locked or “OFF” position before making any assembly adjustments, changing
accessories, performing any inspection, maintenance or cleaning procedures.
Such preventive safety measures reduce the risk of starting the tool accidentally.
Do not use the Cordless Drill if it has been damaged, left outdoors in the
rain, snow, wet or damp environments, or immersed in liquid.
Maintain labels and nameplates on the Cordless Drill.These carry important
information. If unreadable or missing, contact Alltrade for a replacement. 
						

							FUNCTIONAL DESCRIPTION
CONTROLS AND COMPONENTS:
1. Battery Pack
2. Release Buttons on Each Side
3. 120V AC Adapter
4. Charger
5. LED Charging Indicator
6. 10mm (3/8) Keyless Chuck
7. 24+1 Adjustable Torque Settings
Control Ring
8. Forward/Reversing and 
Trigger Lock LeverCOMPONENT MODEL NUMBERBATTERY PACK 691235120V AC ADAPTER 690074CHARGER 69007210mm (3/8) KEYLESS CHUCK690076
9
BATTERY
Before using battery pack, please read carefully all instruc-
tions and cautionarymarkings on battery pack, battery
charger and product using battery.
Do not incinerate the battery pack even if it is severely
damaged or is completely worn out.The battery pack can
explode. 
Do not carry battery packs in aprons, pockets, or tool boxes, product kit
boxes, drawers, etc. with loose metal objects.Battery pack terminals could
be short circuited causing damage to the battery pack, severe burns or fire.
The battery pack is Nickel-Cadmium (Ni-Cad) and is considered to be a toxic
material by the Environmental Protection Agency.Before disposing of dam-
aged or worn out Ni-Cad battery packs, check with your State Environmental
Protection Agency to find out about special restrictions on the disposal of these
battery packs, take them to your local recycling center for proper disposal, or
call 1-800-822-8837.
The battery is not fully charged. Before first use, the battery pack requires 
8-10 hours charge time to be fully charged. Subsequent recharging needs 3-5
hours for the battery to be fully charged. 
Always switch to a fresh battery when tool performance begins to diminish.
Severe heat is most destructive to a battery; the more heat generated, the faster
the battery loses power. A battery that gets too hot can have a shortened life. 
Never over-discharge a battery by using the tool even after tool performance
has decreased.Do not attempt to discharge a tool’s battery by continuing to
pull on the tool trigger. When tool performance begins to diminish, stop the tool
and recharge the battery for optimal performance.
Charge battery pack at ambient temperatures between 50° F – 104° F. 
Store tool and battery pack in locations where temperatures will not exceed
120°F. This is important to prevent serious damage to the battery cells.
The battery pack should always be recharged when the Cordless Drill begins to
run slowly. 
When battery pack is not in use, keep it away from other metal objects such as
paper clips, coins, keys, nails, screws or other small metal objects that can
make a connection from one terminal to another.Shorting the battery terminals
together may cause sparks, burns, or fire.  
9. High/Low Speed Switch
10. Variable Speed Controlled 
Trigger Switch
11. Accessory/Bit Holder
12. Comfort Rubber Grip
13. Led Light
ACCESSORIES:
14. Double Ended Screwdriver Bits (2)
1
13
21112
98
6
7
10
14
3
4
5
® 
						

							REMOVING/ATTACHING BATTERY PACK
REMOVE BATTERY PACK:
1. Press both release buttons on either side of 
the Cordless Drill to release the battery pack.
2. Pull battery pack free of Cordless Drill.
ATTACH BATTERY PACK:
1. Align the raised portion of the battery pack 
with the groove in the battery compartment 
of the Cordless Drill.
2. Press the battery pack into place. Make sure
the latches are securely fastened. Do not use
the Cordless Drill if the battery pack is not
seated properly. 
CHARGER
Before using battery charger, please read carefully all
instructions and cautionary markings on battery charger, battery pack and
product using battery.
The charger will not automatically turn “OFF” when the
battery pack is fully charged.The charging indicator light will remain “ON”
until the charger is disconnected from the electrical outlet.
Use only the charger which accompanied your product or direct replacement as
listed in this manual. Do not substitute any other charger. Use only Alltrade
approved chargers with your product.
Do not disassemble charger.
Do not use charger if it has been damaged, left outdoors in the rain, snow, wet
or damp environments, or immersed in liquid.
The battery pack and charger heat during charging. Place the charger on a flat, 
non-flammable surface away from flammable materials with at least four inches of
clearance to allow proper air circulation around the charger and battery pack.
When the battery pack requires recharging, a 3-5 hour  charge allows the tool to
operate at full power.A charging indicator light on the charger will illuminate to
show that charging is taking place. 
CHARGING BATTERY PACK
CHARGE BATTERY PACK:
1. Make sure the trigger 
on the Cordless Drill 
is in the “OFF”position 
and remove the battery 
pack from the Cordless Drill.
2. Plug 120V AC Adapter 
into household outlet 
and into side of battery 
charger. Insert battery 
pack into battery charger. 
When the battery is placed in
the charger, the red LED 
indicator light will remain on.
3. When fully charged, reattach battery pack onto Cordless Drill, making certain
latches fasten securely. Cordless Drill will not operate properly if the battery
pack is not seated properly.
ASSEMBLY
Be aware that this tool is always in an operating condition
because it does not have to be plugged into an electrical outlet.Always turn
the switch “OFF”and remove the battery pack before changing bits.
12 11
RELEASE
BUTTON
BATTERY
CHARGERBATTERY PACK
120V AC 
ADAPTER
LED LIGHT 
						

							VARIABLE SPEED TRIGGER SWITCH
THIS TOOL IS CONTROLLED 
BY A TRIGGER SWITCH:
• The speed of the Cordless Drill depends 
on the amount of pressure you put on the
trigger.
• The more pressure you apply, the faster
the Cordless Drill will go.
• Release the pressure and the Cordless
Drill will slow down.
BUILT IN LED LAMP
• Press the trigger switch to light up the lamp. The lamp remains on while the
trigger switch is being pressed. The lamp goes out after releasing the trigger.
NOTE: Use a dry cloth to wipe the dirt off the lens of lamp. Be careful not to scratch
the lens of lamp, or it may lower the illumination. 
Do not look into light or see the source of light directly.
FORWARD / REVERSE AND TRIGGER LOCK LEVER
Be sure the trigger is released when changing the position of the lever.
Always store the tool in the“LOCKED/OFF”position.
Always check the direction of the Cordless Drills rotation before use.
TO SELECT THE DIRECTIONS 
OF ROTATION:
• To select forward Cordless Drill 
rotation, press the trigger lock from
left to right flat against the Cordless
Drill body.
• To select reverse, press the trigger
lock lever in the opposite direction.
• The center position locks the tool.
INSTALLING DRILL BIT INTO KEYLESS CHUCK
Before inserting a drill bit or other accessory,make sure the forward/reverse
and trigger lock lever is in the center “OFF”position to prevent accidental starts
that may result in injury.
Do not attempt to tighten drill bits (or any other accessory) by gripping the
front of the chuck and turning the tool on.This may cause personal injury
and/or damage to the chuck.
When removing the bit from the tool, avoid contact with skin and use proper
protective gloves when grasping the bit or accessory.Accessories may be hot
after prolonged use.
1. Hold the rear end of the chuck in
one hand and use the other hand to
rotate the front end in a counter-
clockwise direction to open the jaws
of the chuck.
2. Insert the shank of the bit (or other
accessory) fully into the keyless
chuck, taking care to keep the bit in
the center of the jaws of the chuck.
3. Turn the front end of the chuck clockwise to hold the bit in place.
4. Tighten securely by turning the front end of the chuck clockwise while holding
the rear end.
OPERATING THE DRILL
Never tape the trigger switch down to provide continu-
ous high speed.The tool may fail under such conditions causing fire or 
personal injury.
WARNING
13
TRIGGER
LOCKTRIGGER
SWITCH
LED LIGHT
HOLD HERE
HOLD HERE RELEASE
GRIP
FORWARD
LOCK
REVERSE 
						

							SCREWDRIVING
WHEN DRIVING FASTENERS:
• Always start slowly and gradually increase the speed of the Drill. 
• Release the trigger when you feel the clutch slip.
• Always keep the driver bit straight to prevent damage to the screw. 
• Hold the Drill with both hands to ensure control if the bit should stick or slip.
• To prevent wood from splitting, drill pilot holes into the wood before driving 
in the screws.
DRILLING METAL
WHEN DRILLING HARD METALS:
• Apply a lubricant, such as cutting oil, to the tip of the bit.
• Start with a small hole then enlarge to the required size. Make sure the bit is 
actually cutting and not spinning in the hole as this will dull the edges of the bit.
• Keep enough pressure on the bit to keep it drilling through the material.
DRILLING MASONRY
WHEN DRILLING MASONRY:
• Masonry can be brittle so be careful not to apply too much pressure and crack 
the material.
• Apply enough pressure to keep the bit cutting and not spinning in the hole as this
will dull the edges of the bit.
• Bricks and similar soft materials will require less pressure, concrete will require
much more.
DRILLING WOOD
Use twist bits to drill holes in wood. Make sure the bits are sharp. Pull the bits 
out of the hole frequently to clear chips from the flutes as an overburdened bit 
may overheat. 
HINTS FOR OPTIMUM USE
DRILLING:
• Keep the right amount of pressure in a straight line with the drill bit. Too little and
the bit will spin without cutting, too much and the motor may stall.
16
TORQUE SETTINGS
To prevent damaging the tool or driving screw too deep
into work piece, release the trigger when you feel the clutch slip.
THE CONTROL RING ADJUSTS THE LEVEL OF TORQUE:
• For light duty work, use lower settings.
• For heavy duty work, use higher settings.
PROPER SETTING FOR DRIVING SCREWS:
1. Set the ring on the lowest 
setting to begin.
2. Try tightening the first screw. 
If the drill drives smoothly, 
proceed with the next screw.
3. If the Drill’s clutch slips, 
increase the torque setting 
and try again until the Drill 
drives the screw without incident.HIGH / LOW SPEED (GEAR) SHIFTING
FOR LOW SPEED SETTING:
• Slide the switch on top of the 
Drill to Position 1 for high
torque applications and driv-
ing screws.
FOR HIGH SPEED SETTING:
• Slide the switch to Position 2 
for light duty projects.
15
CONTROL RING
HIGH SPEED LOW SPEED 
						

							Regularly clean the ventilation slots in your tool and charger using only a soft
brush or dry cloth.
Never open the Cordless Drill case, battery pack or charger.Do not attempt to
repair the Cordless Drill, battery pack or charger yourself. Opening any of these
parts will void your warranty.
ACCESSORIES
Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may become hazardous when used on
another tool.
Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets.
If you must use an extension cord, be sure that the gauge is large enough to carry
the amount of current necessary for your power tool.If not, your tool may experi-
ence a loss of power, excessive voltage drop or overheating. The smaller the gauge
number, the heavier the cord (see table on next page).
RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLS
TOOL CURRENT RATING CONDUCTOR SIZE IN A.W.GAMPERE 10FT. 25FT. 50FT. 100FT.
3-6 18 18 18 186-8 18 18 18 168-10 18 18 18 1410-12 16 16 14 1412-16 14 12 12 -16-20 12 12 12 -
18
• Just before the drill tip breaks though the other side of the work piece drill more
slowly and decrease pressure on the tool. This will prevent stalling and leave a
cleaner hole.
• Use a block of wood to back up work pieces that may splinter.
• Use spade bits when drilling large diameter holes in wood.
• Use HSS drill bits when drilling in metal.
• Use masonry bits when drilling in soft masonry.
• Use a lubricant when drilling metals other than cast iron, aluminum, copper, 
and brass.
• When drilling, start the hole slowly, allowing the bit to drill deep enough to prevent
slipping at higher speeds.
• Never try to start a stalled Drill by clicking the trigger switch “ON”and “OFF”.
This may damage your tool.
• To reduce jamming, always keep the Drill running when pulling the bit out of a 
finished hole.
SCREWDRIVING:
• Always use the correct type and size of screwdriver bit.
• If screws are difficult to tighten, try applying a small amount of washing liquid or
soap as a lubricant.
• Always hold the tool and screwdriver bit in a straight line with the screw.
MAINTENANCE AND CLEANING
Always remove the battery pack before attempting
cleaning or maintenance.
This Cordless Drill is lubricated before it leaves the 
factory. This lubrication should last for the life of the tool. No further 
lubrication is required.
Use only mild soap and a damp cloth to clean the tool.Never let any liquid get
inside the casing. Never immerse any part of the tool in a liquid. Always keep the
ventilation openings clear.
Always clean the battery pack using only a dry cloth. Do not use liquids. 
Always unplug the charger before cleaning it.
17 
						

							SPECIAL WARRANTY NOTE TO CONTRACTORS AND COMMERCIAL USERS:This
Kawasaki™ portable power tool is offered as a home use tool and carries a HOME
USE WARRANTY. This tool is made for home use in the execution of 
projects and repairs in and around the home. Use of the tool for COMMERCIAL 
PURPOSES OR ON A JOBSITEis not covered under this warranty.
The date of purchase shall be the date of shipment to the original purchaser, or the
date the original purchaser took possession, custody or control of the product,
whichever occurred first. This warranty shall be null and void if the product or any
component thereof is modified, altered or used for any commercial purpose or on
a jobsite. This warranty does not apply to any other product and/or component
thereof manufactured or distributed by Alltrade, and does not apply to products
and/or components thereof designed, manufactured and/or assembled by others,
for which Alltrade makes no warranties whatsoever.THERE ARE NO WARRANTIES
WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF.
Warranty Performance 
By purchasing the product, purchaser expressly acknowledges and agrees that their
sole and exclusive remedy under this warranty shall be strictly limited to the repair
or replacement of any covered nonconforming items or parts thereof provided that
any such nonconforming item and/or part is promptly returned to Alltrade’s facility
postage pre-paid and insured (address: ALLTRADE Warranty Claims & Repair, 
1431 Via Plata, Long Beach, CA 90810, Attn: Customer Service #1-800-590-3723)
within the applicable warranty period, with a written request by purchaser that
Alltrade repair and/or replace the nonconforming item and/or part. We recommend
that you keep the original product packaging in the event you need to ship the unit.
We suggest the package be insured against loss or in transit damage. When 
sending your product include your name, address, phone number, dated proof 
of purchase (or copy), and a statement about the nature of problem. Warranty 
coverage is conditioned upon purchaser furnishing Alltrade with adequate written
proof that they are the original purchaser and of the original purchase date. Parts
returned, freight prepaid and insured, to Alltrade’s facility (see above address) will
be inspected and, at Alltrade’s option, repaired and/or replaced free of charge if
found to be defective and subject to warranty. Alltrade retains the sole discretion 
to determine whether any item or part is nonconforming and, if so, whether the 
item and/or part will be repaired and/or replaced. If the unit is repaired, new or
reconditioned replacement parts may be used. If Alltrade chooses to replace 
the product, it may replace it with a new or reconditioned one of the same or 
comparable design. The repaired or replaced unit will be warranted under the terms
of the remainder of the warranty period. Typically, a defective product that is
returned within the first 30 days after the purchase date will be replaced; for items
returned after the first 30 days and within the warranty period, covered defective
parts not subject to normal wear and tear or other exclusions will be repaired or
replaced, at Alltrade’s option. During the warranty period, Alltrade will be responsi-
ble for the return shipping charges. Alltrade’s repair and/or replacement of any non-
SPECIFICATIONS
SPECIFICATIONSVoltage 19.2V No Load Low Speed 0-400/min.No Load High Speed 0-1100/min.Torque Settings 24+1 DrillChuck Capacity Up to 10mm (3/8) Charger Input 120V  60HzCharging Time Approx. 3-5 hoursBattery Type Ni-Cad
PROTECTING THE ENVIRONMENT
BATTERIES
Alltrade batteries can be recharged many times. At the end of their useful life, 
recycle batteries with due care for our environment. 
Ni-Cad and Ni-MH batteries are recyclable. Take them to your local recycling center
or call 1-800-822-8837. Collected batteries will be recycled or disposed of properly.
OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS
Alltrade offers a full range of Kawasaki™ tools that make DIY jobs easy. If you would
like further information on the following products, please contact Alltrade Customer
Service Department at 1-800-590-3723. 
Cordless Drills/Screwdrivers
Impact Wrenches
Sanders
Jigsaws
Circular Saws
Angle Grinders
2 YEAR LIMITED HOME USE WARRANTY
Express and Exclusive Limited Home Use Warranty to Original Retail Buyer
Alltrade Tools LLC (hereinafter Alltrade) expressly warrants to the original retail
purchaser of the accompanying KAWASAKI™ portable power tool and no one else
all parts of the product (except those parts referred to below which are specifically
excluded from such warranty (see Exclusions)) to be free from defects in materials
and workmanship for a period of two years from original date of purchase.
19Reciprocating Saws
Routers
Rotary Tools
Corded and Cordless Multi-Purpose Tools
Wide Range of Accessories and more 
						

							EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. NO WARRANTY, ORAL OR WRITTEN, OTHER THAN THE ABOVE 
WARRANTY IS MADE WITH REGARD TO THIS PRODUCT. ALL EXPRESS AND/OR
IMPLIED WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS BY ALLTRADE
AND/OR ITS REPRESENTATIVE(S) REGARDING THE DESIGN, MANUFACTURE,
PURCHASE, USE AND/OR OPERATION OF THE PRODUCT OR ANY COMPONENT
THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH WARRANTY,
GUARANTY AND/OR REPRESENTATION, WRITTEN OR ORAL, ARISES BY 
OPERATION OF LAW AND/OR EQUITY AND/OR BY ANY ACT OR OMISSION OF
ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE PURCHASER, INCLUDING
BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY EXPRESSLY
EXCLUDED AND DISCLAIMED BY ALLTRADE AND/OR ITS REPRESENTATIVES.
PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH 
WARRANTIES AND RIGHTS, CLAIMS AND/OR CAUSES OF ACTION ARISING
THEREFROM OR BASED THEREON. PURCHASER’S SOLE AND EXCLUSIVE 
REMEDY IS AS STATED ABOVE.
Limitation Of Liability
IN NO EVENT SHALL ALLTRADE AND/OR ITS REPRESENTATIVE(S) BE LIABLE FOR
INDIRECT, INCIDENTAL, SPECIAL AND/OR CONSEQUENTIAL DAMAGES OF ANY
KIND ARISING OUT OF OR RELATED TO, DIRECTLY OR INDIRECTLY, ANY BREACH
OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND/OR ITS 
REPRESENTATIVE(S) AND PURCHASER, ANY WARRANTY HEREUNDER, 
AND/OR THE EXISTENCE, DESIGN, MANUFACTURE, PURCHASE, USE AND/OR
OPERATION OF ANY ITEM(S) SOLD HEREUNDER EVEN IF ALLTRADE AND/OR ITS
REPRESENTATIVE(S) HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH
DAMAGES. IN NO EVENT, WHETHER AS A RESULT OF A BREACH OF CONTRACT,
WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL 
ALLTRADE’S AND/OR ITS REPRESENTATIVE(S)’ LIABILITY EXCEED THE PRICE OF
THE PRODUCT. ANY AND ALL LIABILITY CONNECTED WITH THE USE OF 
THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY
PERIODS SPECIFIED ABOVE.
Limitations on Warranty Disclaimers 
Some states do not allow limitations on how long an implied warranty lasts 
and some states do not allow the exclusion or limitation of the incidental or 
consequential damages, so part or all of the above limitations or exclusions may not
apply to you. This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
If your product is not covered by this warranty, please call our Customer Service
Department toll free at 1-800-590-3723 for general repair information and charges. 
22
conforming item and/or part thereof shall constitute fulfillment of all 
obligations to the purchaser. Alltrade shall not be responsible or liable for any
expense, including freight charges, or repairs made outside Alltrade’s facility, unless
expressly agreed to by Alltrade in writing. Under no circumstances shall Alltrade
bear any responsibility for loss of the unit, loss of time or rental, inconvenience,
commercial loss or consequential damages.
Exclusions
This warranty does not cover parts damaged due to normal wear, abnormal 
conditions, misapplication, misuse, abuse, accidents, operation at other than 
recommended pressures or temperatures, improper storage or freight damage.
Parts damaged or worn by operation in dusty environments are not warranted.
Failure to follow recommended operating and maintenance procedures also 
voids warranty.
This limited warranty does not apply to accessory items such as drill bits, 
screwdriving bits, circular saw blades, jigsaw blades, grinding wheels, sanding
sheets and other related items.
DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING, ACCIDENT, ABUSE,
NEGLIGENCE, FAILURE TO FOLLOW INSTRUCTIONS, UNAUTHORIZED REPAIRS
OR ALTERATIONS, DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY, 
USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES, 
COMMERCIAL AND RENTAL APPLICATIONS OR OTHER CAUSES UNRELATED TO
PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS
WARRANTY.
Alltrade will not be liable for the following: labor charges, loss or damage resulting
from improper operation, maintenance or repairs made by other persons; 
pre-delivery services such as assembly, oil or lubricants, and adjustment; 
maintenance services that are normally required to maintain the product.
The use of other than genuine Alltrade Repair Parts will void warranty.
Warranty Disclaimers 
EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES, 
GUARANTIES AND/OR REPRESENTATIONS. EXCEPT FOR THE LIMITED WARRANTY
PROVIDED ABOVE, ALL OTHER EXPRESS WARRANTIES, GUARANTIES AND/OR
REPRESENTATIONS BY ALLTRADE AND/OR ITS REPRESENTATIVE(S) REGARDING
THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE
PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF
WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION,
WRITTEN OR ORAL, ARISES BY OPERATION OF LAW AND/OR EQUITY AND/OR BY
ANY ACT OR OMISSION OF ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE
BUYER, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE
AND/OR ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND WILLINGLY
WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS AND/OR 
CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON. PURCHASER’S
SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE.