Dell Alienware Aurora R5 Service Manual

							Replacing the stability foot
WARNING: Before working inside your computer, read the 
safety information that shipped with your computer and  follow the steps in 
Before working inside your computer. 
After working inside your computer, follow the instructions 
in 
After working inside your computer. For more safety best 
practices, see the Regulatory Compliance home page at 
www.dell.com/regulatory_compliance.
 
Procedure
1 Tilt the computer towards the front until the base is facing up.
2 Align the tabs on the stability foot with the slots on the bottom cover and  snap the stability foot to lock it in place.
3 Tilt the computer back to the upright position.
21 
						

							Removing the left-side cover
WARNING: Before working inside your computer, read the 
safety information that shipped with your computer and  follow the steps in 
Before working inside your computer. 
After working inside your computer, follow the instructions 
in 
After working inside your computer. For more safety best 
practices, see the Regulatory Compliance home page at 
www.dell.com/regulatory_compliance.
 
Procedure
NOTE: Ensure that you remove the security cable and security screw from 
the security-cable slot (if applicable).
1 Pull the side panel release latch.
22 
						

							2 Release the left-side cover away from the chassis and then lift it from the computer.1side panel release latch2top cover3left-side cover23 
						

							Replacing the left-side cover
WARNING: Before working inside your computer, read the 
safety information that shipped with your computer and  follow the steps in 
Before working inside your computer. 
After working inside your computer, follow the instructions 
in 
After working inside your computer. For more safety best 
practices, see the Regulatory Compliance home page at 
www.dell.com/regulatory_compliance.
 
Procedure
Align the tabs on the left-side cover with the slots on the chassis and snap the  left-side cover to lock it in place.
24 
						

							Removing the right-side 
cover
WARNING: Before working inside your computer, read the 
safety information that shipped with your computer and  follow the steps in 
Before working inside your computer. 
After working inside your computer, follow the instructions 
in 
After working inside your computer. For more safety best 
practices, see the Regulatory Compliance home page at 
www.dell.com/regulatory_compliance.
 
25 
						

							Procedure
1 Carefully pry around the edges of the right-side cover from the chassis.
1chassis2right-side cover26 
						

							2 Disconnect the lighting cable from the right-side cover.1right-side cover2lighting cable
3 Lift the right-side cover off the chassis.
27 
						

							Replacing the right-side 
cover
WARNING: Before working inside your computer, read the 
safety information that shipped with your computer and  follow the steps in 
Before working inside your computer. 
After working inside your computer, follow the instructions 
in 
After working inside your computer. For more safety best 
practices, see the Regulatory Compliance home page at 
www.dell.com/regulatory_compliance.
 
Procedure
1 Connect the lighting cable to the right-side cover.
2 Align the tabs on the right-side cover with the slots on the chassis and  snap the right-side cover to lock it in place.
28 
						

							Removing the top-cover 
assembly
WARNING: Before working inside your computer, read the 
safety information that shipped with your computer and  follow the steps in 
Before working inside your computer. 
After working inside your computer, follow the instructions 
in 
After working inside your computer. For more safety best 
practices, see the Regulatory Compliance home page at 
www.dell.com/regulatory_compliance.
 
Prerequisites
1 Remove the left-side cover.
2 Remove the right-side cover.
Procedure
1 Remove the screws that secure the top cover to the chassis.
2 Disconnect the lighting cable from the top cover.
29 
						

							3 Slide the lighting cable through the slot on the chassis.1lighting cable2chassis3screws (2)4top cover
4 Starting from the rear, release the tabs on the top cover from the slots on 
the chassis.
30