Aleratec RoboJet Disc Autoloader User Guide
Have a look at the manual Aleratec RoboJet Disc Autoloader User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 61 Aleratec manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
USER GUIDE Aleratec RoboJet Di\fc Autoloader™ \bart No. 360104EU
www.aleratec.com Copyright/Model Ident\iification The content of this manual is for informational purposes only and is subject to change without notice. This manual is copyright with all rights reserved. Under copyright laws, this manual and the software described within may not be copied, except in the normal use of the product(s) described within or to make a backup copy. Copyright© 2012 Aleratec, Inc. 9851 Owensmouth Avenue Chatsworth, CA 91311 U.S.A. Aleratec® is a registered trademark and RoboJet Disc Autoloader™ is a trademark of Aleratec, Inc. Check out Aleratec Online! • Blog.Aleratec.com • Facebook.com/Aleratec • Twitter.com/Aleratec • YouTube.com/Aleratec Please record the following information to help expedite any warranty claim: Model No. _____________________Serial No. _____________________ Date Purchased ________________________________________________ Place of Purchase ______________________________________________
www.aleratec.com Radio/TV Interferen\ice Statement The equipment described in this guide emits radio frequency energy. If it is not installed in accordance with the manufacturer’s instructions, it may cause interference with radio or television reception. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency ener gy. If not installed and used in accordance with the instruction manual, this equipment may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be verified by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and the receiver. • Connect the equipment to an electrical outlet on a circuit that is different from the circuit to which the receiver is connected. • Consult your dealer or an experienced radio/TV technician for help. This equipment has been certified to comply with the limits for a Class B computing device, pursuant to FCC Rules. In order to maintain compliance with FCC regulations, shielded cables must be used with this equipment. Operation with non-approved equipment or unshielded cables is likely to result in interference to radio and TV reception. The user is cautioned that changes and/or modifications made to this equipment, without the approval of manufacturer, could void the user’s authority to operate this equipment.
www.aleratec.com Table of Content\f Introduction ..................\i..................\i..................\i..................\i...............1 Product Features .....................................................................................1 Included Items ........................................................................................1 Key Items ................................................................................................2 \brecaution\f ..................\i..................\i..................\i..................\i...............3 Location ..................................................................................................3 Printer Requirements ..............................................................................4 In\ftallation ..................\i..................\i..................\i..................\i.................5 Unpacking the Unit .................................................................................5 Printer Installation ..................................................................................5 Minimum Hardware and Software Requirements ..................................6 Operation ................................................................................................6 Transportation .........................................................................................6 Installing Aleratec’s RoboJet Disc Autoloader Software ........................7 Setup Autoloader ....................................................................................9 U\fing the RoboJet D\ii\fc Autoloader ..................\i..................\i...13 Powering on the Printer ........................................................................13 Getting to know the Aleratec Autoloader application ...........................16 Using the Aleratec RoboJet Disc Autoloader Application ....................18 Trouble\fhooting ..................\i..................\i..................\i..................\i.....20 Specification\f ..................\i..................\i..................\i..................\i.........24 Technical Support ..................\i..................\i..................\i..................\i..26 Service and Support\i ..................\i..................\i..................\i.................27 Technical Support FAX Back Form ..................\i..................\i...........30
www.aleratec.com1 Introduction Thank you for purchasing the Aleratec RoboJet Disc Autoloader. Please read this User Guide thoroughly before using this product. \broduct Feature\f The Aleratec RoboJet Disc Autoloader is a fully automatic disc loading system for compatible printers. Features include: ▪Up to 100 disc capacity ▪Autoloader lets you add more blanks and remove finished discs while the system is printing ▪Simple, reliable and fast disc feed system ▪Easy installation Included Item\f A. USB2.0 H\fb B. USB cable C. D\bsc B\bn, 50 and 100 D\bsc Capac\bty D. Power Adapter cable E. D\bsc B\bn, 100-D\bsc Capac\bty F. D\bsc B\bn, 50-D\bsc Capac\bty G. 2 A\ftoloader D\bsc Trays (one \bs already \bn the A\ftoloader \fn\bt) E D F C A B G
www.aleratec.com2 Introduction Key Item\f on the Ro\iboJet Di\fc Autoloader A. D\bsc Holder Post Slots B. D\bsc Load Mechan\bsm C. D\bsc B\bn Holder D. A\ftoloader D\bsc Tray E. Pr\bnter Mode Sw\btch F. USB Port G. Power Port C F G BE AD
www.aleratec.com3 1. Choose a flat, level s\frface for the pr\bnter and A\ftoloader near a table edge. (Th\bs \bs \bmportant beca\fse the d\bsc b\bn w\bll hang over the table edge once \bnstalled) 2. Allow adeq\fate clearance for mov\bng parts. 3. Do not place near heat so\frces s\fch as rad\bators or a\br d\fcts, or \bn a place s\fbject to d\brect s\fnl\bght, excess\bve d\fst, mechan\bcal v\bbrat\bon or shock. 4. Good care w\bll help ass\fre max\bm\fm prod\fct l\bfe. Improper operat\bng env\bronment and m\bs\fse may vo\bd the warranty. \brecaution\f Before installing your RoboJet Disc Autoloader, please read the following. Location Avoid placing the RoboJet Disc Autoloader in a location subject to: • High humidity • High temperature • Excessive dust • Mechanical vibration • Direct sunlight • Electromagnetic radiation
www.aleratec.com4 \brinter Requirement\f\i The RoboJet Disc Autoloader is designed to work specifically with the Epson Artisan 50 inkjet printer (not included), although it can also be made to work with certain other models of Epson inkjet printers which support disc printing. Below is a list of other compatible Epson printer models. Designed for Epson Artisan 50 Can also work with Epson models: Asia: R290, T50 America: R280 Europe: R285, P50 Japan: E301, E302 \brecaution\f