Home > Aleratec > Hard Disk > Aleratec 15 HDD Cruiser Hard Disk Drive Duplicator and Sanitizer User Guide

Aleratec 15 HDD Cruiser Hard Disk Drive Duplicator and Sanitizer User Guide

    Download as PDF Print this page Share this page

    Have a look at the manual Aleratec 15 HDD Cruiser Hard Disk Drive Duplicator and Sanitizer User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 61 Aleratec manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							www.aleratec.com5
    Precautions
    Before installing your 1:5 HDD Cruiser, please read the following.
    Installation
    Avoid placing the 1:5 HDD Cruiser in a location subject to:
    • High humidity
    • High temperature
    • Excessive dust
    • Mechanical vibration
    • Direct sunlight
    • Electromagnetic radiation
    Power
    This product has a manually switchable power supply. Make	sure	that	the	power	
    supply	is	set	to	the	proper 	voltage	for	your	region.
    Choose a Good Location
    1. Allow adequate clearance for moving parts.
    2. Do not place near heat sources such as radiators or air ducts, or in a place 
    subject to direct sunlight, excessive dust, mechanical vibration or shock.
    3. Disconnect the AC adapter from the outlet if the product is not used for an 
    extended period of time. 
    4. Proper care will help assure maximum product life. Improper operating 
    environment and misuse may void the warranty. 
    Operation
    Do not move the 1:5 HDD Cruiser during operation. This may cause a malfunction 
    or other undesirable results.
    Avoid exposing the unit to sudden changes in temperature as condensation may 
    form inside the 1:5 HDD Cruiser. Should the surrounding temperature suddenly rise 
    while the 1:5 HDD Cruiser is on, wait at least one hour before turning of f the power. 
    Operating the duplicator immediately after a sudden increase in temperature may 
    result in a malfunction.
    Transportation
    Keep the original packing materials for future moving or shipping of the 1:5 HDD 
    Cruiser.  
    						
    							www.aleratec.com6
    Overview
    Power Up Sequence
    During the normal power-up sequence of the 1:5 HDD Cruiser, the following 
    information will be displayed.
    • Figure 1 shows the firmware version
    • Figure 2 shows the memory initialization
    • Figure 3 shows the scanning of the drives
    • Figure 4 shows the number of drives loaded. 
    • Figure 5 shows the first function. 
    ENTESC
    
    
    HDD Cruiser2055PF ver:A.24Q
    Initialize SDRAMENTESC
    
    
    Detect DrivesPlease wait...ENTESC
    
    
    Detect DrivesFound 0 DevicesENTESC
    
    
    1. Copy HDDENTESC
    
      
    						
    							www.aleratec.com7
    Overview
    Main Menu
    There are eleven main menu items that can be seen in the 1:5 HDD Cruiser Copy 
    Controller Display Panel. These are:
    1.
    2.
    3.
    4.
    5.
    Note: The Advanced Setup function is a hidden menu. To access 
    this menu, press ESC for 3 seconds. After you have completed any 
    desired adjustments, press ESC to exit Advanced Setup.
    ENT
    
    
    1. Copy HDDESC
    ENTESC
    
    
    2. Async Copy HDD
    ENTESC
    
    
    3. Compare HDD
    ENTESC
    
    
    4. Async Compare
    ENTESC
    
    
    5. PreScan Source
    ENT
    
    
    6. Rescan BUSESC
    ENTESC
    
    
    7. Source Size
    ENTESC
    
    
    8. Secure Erase
    ENTESC
    
    
    9. Overwrite
    ENTESC
    
    
    10. Setup
    6.
    7.
    8.
    9.
    10. 
     
      
     
    11.ENTESC
    
    
    11. Adv Setup  
    						
    							www.aleratec.com8
    Overview
    Subfunctions
    The “Setup” menu has 13 subfunctions. These are:
    Language
    Copy Size
    Startup Menu
    Auto Compare
    Button Sound
    Device Info
    System Info
    Fast Copy
    Auto Start Drive
    Auto Start Timer
    ENTESC
    
    
    10. Setup
    (Not Supported)
    Tolerance Size
    BootTime Delay
    Quick Compare
    (Not Supported)  
    						
    							www.aleratec.com9
    Overview
    The “Advanced Setup” menu has nine subfunctions. These are:
    Read Error Skip
    Update Firmware
    Compare Firmware
    Quick Erase HDD
    Full Erase HDD
     
     
    H/W Diagnostic
    ENTESC
    
    
    11. Adv Setup
    Load Default
    Copy HPA
    Burn In   
    						
    							www.aleratec.com10
    Using the 1:5 HDD Cruiser 
    Loading the Hard Drives
    1. Open the drive tray doors by lifting the tab on the left side of each drive bay 
    you wish to use.  
    2. Take the Hard Disc Drive (HDD) and align the drive’s SATA plug to the lower 
    right hand side of the drive bay. 
    3. Slide the HDD into the drive bay until it stops. The drive will still be about 1 
    inch outside of the bay. When the door is closed it will push and plug the HDD 
    into the duplicator.
    4. Swing the drive bay door closed and press the left side of the door until the tab 
    latches. When it latches, a click can be felt and heard. 
    Note: If you are duplicating, the source hard disk drive goes in the top 
    bay.
    Source Drive
    Target Drives  
    						
    							www.aleratec.com11
    Using the 1:5 HDD Cruiser 
    Removing Hard Drives
    1. Open the drive tray doors by pulling the handle/tab on the left side of each 
    drive tray door. 
    Note: Do not attempt to remove the hard drive if the drive activity 
    LED is on.
    2. To disengage the HDD, swing the drive tray door to the full open position. 
    3. Pull drive forward and remove drive.  
    						
    							www.aleratec.com12
    Using the 1:5 HDD Cruiser 
    Main Menu
    Copy HDD
    The “Copy HDD” function performs an actual copy from a source HDD to one or 
    more target HDDs. The target HDDs must be at least as large as the source. The 1:5 
    HDD Cruiser will copy every block of capacity on the source HDD. 
    1. Load the source HDD and the target HDDs into the 1:5 HDD Cruiser. The 
    system will auto-detect the hard drives. After the drives have been detected, a 
    screen similar to the one below will be displayed. 
    Note: Before copying be sure that the capacity of the target HDD is 
    equal to or larger than the source hard drive. 
    2. Press ENT to start copying. The system will auto-detect the hard drives. The 
    following information will be displayed. 
    3. During the copy process the 1:5 HDD Cruiser will display progress information.
    The amount of data remaining to be transferred (shown in gigabytes), and time 
    will be displayed as the percentage of completion increases. 
    Note: The copying speed, capacity and duration may vary from one 
    source hard drive to another. 
    ENTESC
    
    
    1. Copy HDD149.1GB
    ENTESC
    
    
    Detect DrivesPlease wait...
    ENTESC
    
    
    Copy- 36MB/s 0%235.7GB 1:48  
    						
    							www.aleratec.com13
    Using the 1:5 HDD Cruiser 
    4. Once duplication is complete, a job status screen will be displayed.
    ENTESC
    
    
    1. Copy HDDOK:1 Fail: 0  
    						
    							www.aleratec.com14
    Using the 1:5 HDD Cruiser 
    Main Menu
    Async Copy
    The function “Async Copy” allows you to insert target drives during the copying 
    operation. During the process, you can insert another drive as a target of the Async 
    Copy operation and the unit will automatically copy to this new drive as well.  
    1. Load the source HDD and the target HDDs into the 1:5 HDD Copy Cruiser. 
    The system will auto-detect the hard drives. After the drives have been 
    detected, a screen similar to the one below will be displayed. 
    Note: Before copying be sure that the capacity of the target HDD is 
    equal to or larger than the source hard drive. 
    2. Press ENT to start copying. The system will auto-detect the hard drives. The 
    following information will be displayed. 
    3. During the copy process the 1:5 HDD Copy Cruiser will display progress 
    information.
    The amount of data remaining to be transferred (shown in gigabytes), and time 
    will be displayed as the percentage of completion increases. 
    Note: The copying speed, capacity and duration may vary from one 
    source hard drive to another. 
    ENTESC
    
    
    2. Async Copy
    ENTESC
    
    
    Detect DrivesPlease wait...
    ENTESC
    
    
    Copy- 36MB/s 0%235.7GB 1:48  
    						
    All Aleratec manuals Comments (0)

    Related Manuals for Aleratec 15 HDD Cruiser Hard Disk Drive Duplicator and Sanitizer User Guide