Aleratec 116 HDD Copy Cruiser IDESATA HighSpeed Duplicator User Guide

							www.aleratec.com25
Using the HDD Copy Cruiser IDE/SATA High-Speed 
Main Menu
Overwrite 
F.			Secure	Erase	
The “Secure Erase” function will sanitize (wipe clean of all data) the hard disk 
drives connected to the HDD Copy Cruiser IDE/SATA High-Speed using algorithms 
programmed by the hard drive manufacturer.  Since this function is native to the 
hard drive, it is very fast and reliable.  Almost all modern SATA hard drives sup-
port this feature.  In the rare case that Secure Erase is not supported, please use the 
“Overwrite” function to sanitize your hard drives. 
F1. To perform a Secure Erase, scroll to “Secure Erase” and press OK. The 
following screen will be displayed. 
F2. The estimated time elapsed for the Secure Erase process will be displayed. 
F3. When the process is finished, the following screen will be shown. 
 
 
 
 
 
 
Note: Not all hard disk drives support Secure Erase, although most modern SATA HDDs do.  If any of your drives do not support Secure Erase, you will see a “Dev. Not Support” error message.

ESC
OK[ 4. Overwrite ]6. Secure Erase

ESC
OKSecure Erase Pass: 11          Fail: 0

ESC
OKIn ProcessElapsed    13:30  
						

							www.aleratec.com26
Using the HDD Copy Cruiser IDE/SATA High-Speed 
Main Menu
Utility - Show HDD Info
This function will display information about the hard drives inserted into the unit. 
You may use the arrow buttons to select hard drives loaded into different bays.
1. With the source and target HDDs loaded use the arrow buttons (or) to 
select “Utility”. The following screen will be displayed. 
 
2. Press OK to select. The following information will be displayed.
 
3. To display the information about the hard drives in the duplicator, select “Show 
HDD Info” and press OK. The following information will be displayed. Use 
the arrow buttons to scroll up and down to view other hard drives.

ESC
OKAleratec 5. Utility

ESC
OK[ 5. Utility ]5.1 Show HDD Info

ESC
OK[ 01 ]  232G       WDC WD 2500  
						

							www.aleratec.com27
Using the HDD Copy Cruiser IDE/SATA High-Speed 
Main Menu
Utility - Update System
Before attempting to use this feature, please contact Aleratec Support.
1. Use the arrow buttons (or) to select “Utility”. The following screen will be 
displayed. 
 
2. Press OK to select. The following information will be displayed.
Use the arrow buttons to scroll between the types of utilities: Update BIOS and 
Create Update HDD.  
 A.			Update	BIOS		
Before attempting to use this feature, please contact Aleratec Support.
A1. To perform a BIOS update, select “Update BIOS” and press OK. 
 
A2. The following information will be displayed.  

ESC
OKSearching SourcePartition    1    50%

ESC
OKAleratec 5. Utility

ESC
OK[ 5. Utility ]5.2 Update System

ESC
OK[ 5.2 Update System ] 5.2.1 Update BIOS  
						

							www.aleratec.com28
Using the HDD Copy Cruiser IDE/SATA High-Speed 
Main Menu
Utility - Update System
 B.			Create	Update	HDD			
For technical support use only.
B1. To create an Update HDD, select “Create Update HDD” and press OK. 
 
B2. The following information will be displayed. Press OK	to confirm.  
B3. The formatting is now complete. 

ESC
OK[ 5.2 Update System ] 5.2.2 Create Update HDD

ESC
OKDo FORMAT HDD#1Confirm?

ESC
OKFORMAT Complete!  
						

							www.aleratec.com29
Using the HDD Copy Cruiser IDE/SATA High-Speed 
Main Menu
Utility - System Info
This function will help you give more technical information sometimes required by 
technical support.
1. Use the arrow buttons (or) to select “Utility”. The following screen will be 
displayed. 
 
2. Press OK to select. The following information will be displayed.
 
 
 
 
 
 
3. Use the arrow buttons (or) to select “System Info” and press OK.
 
4. The following information will be displayed. 

ESC
OKAleratec 5. Utility

ESC
OK[ 5. Utility ]5.1 Show HDD Info

ESC
OK[ 5. Utility ]5.3 System Info

ESC
OKAleratec     1-11 Ver: 2.32.0  
						

							www.aleratec.com30
Using the HDD Copy Cruiser IDE/SATA High-Speed 
Main Menu
Setup
The “Setup” menu contains configuration options for the HDD Copy Cruiser 
IDE/SATA High-Speed. It is suggested to use the factory defaults for optimum 
performance. 
1. Use the arrow buttons (or) to select “Setup”. Press OK to select. The 
following screen will be displayed. 
 
2. Use the arrow buttons to scroll between the types of Setup functions: Copy 
Area, Skip Error, Erase Master, Unknown Format, Transfer Rate, Buzzer, 
Language, Advanced Setup, and Restore Default.  
 
 
 
 
 

ESC
OKAleratec 6. Setup  
						

							www.aleratec.com31
Using the HDD Copy Cruiser IDE/SATA High-Speed 
Main Menu
Setup - Copy Area
This function specifies which data is to be copied from the Source hard drive.
1. In the Setup menu, use the arrow buttons (or) to select “Copy Area”. The 
following screen will be displayed. 
 
2. Press OK to select. Use the arrow buttons to scroll between the types of 
functions within the Copy Area menu: System and Files, ALL Partitions, and 
Whole HDD.  
3.	 System	and	Files: This function will copy only System and Data files located    
on the first partition of the source HDD.
	
	
	
	
	
4.	 ALL	Partitions: This function will copy only System and Data files located on  
any partition of source HDD.
	
	
	
	
	
5.	 Whole	HDD: This function will copy the complete HDD including free space.  
If you need to also copy HPA, please refer to Advanced Setup on page 38. 

ESC
OK[ 6. Setup ]6.1 Copy Area

ESC
OK[ 6.1 Copy Area ]  6.1.1 System and Files

ESC
OK[ 6.1 Copy Area ] 6.1.2 ALL Partitions

ESC
OK[ 6.1 Copy Area ] 6.1.3 Whole HDD  
						

							www.aleratec.com32
Using the HDD Copy Cruiser IDE/SATA High-Speed 
Main Menu
Setup - Skip Error
This function will set the duplicator to be able to overwrite the source drive when 
preforming any overwrite function.
1. In the Setup menu, use the arrow buttons (or) to select “Skip Error”. 
The following screen will be displayed. Press OK to select.

ESC
OK[ 6. Setup ] 6.2 Skip Error  
						

							www.aleratec.com33
Using the HDD Copy Cruiser IDE/SATA High-Speed 
Main Menu
Setup - Erase Master
This function controls whether the hard disk drive inserted into the Source bay may 
be altered by an overwrite or Secure Erase.
1. In the Setup menu, use the arrow buttons (or) to select “Erase Master”. 
The following screen will be displayed. 
 
2. Press OK to select. Use the arrow buttons to scroll between Enable or Disable 
options.  
 
 
 
 
 
 
 
 
 
 
 
 
3. Press OK to Enable or Disable the erasing of the master disc.
 

ESC
OK[ 6. Setup ] 6.3 Erase Master

ESC
OK6.3 Erase MasterEnable

ESC
OK6.3 Erase MasterDisable  
						

							www.aleratec.com34
Using the HDD Copy Cruiser IDE/SATA High-Speed 
Main Menu
Setup - Unknown Format
This function will allow you to copy non standard formatted HDD.
1. In the Setup menu, use the arrow buttons (or) to select “Unknown 
Format”. The following screen will be displayed. 
 
2. Press OK to select. Use the arrow buttons to scroll between the Copy Unknown 
or Skip Unknown options.  
 
 
 
 
 
 
 
 
 
 
 
 
 
3. Press OK to Copy Unknown or Skip Unknown when formatting hard drives.
 

ESC
OK[ 6. Setup ] 6.4 Unknown Format

ESC
OK[ Unknown Format ]Copy Unknown

ESC
OK[ Unknown Format ]Skip Unknown