Home > Aleratec > Hard Disk > Aleratec 1118 USB Copy Tower SA USB Flash Drive Duplicator User Guide

Aleratec 1118 USB Copy Tower SA USB Flash Drive Duplicator User Guide

    Download as PDF Print this page Share this page

    Have a look at the manual Aleratec 1118 USB Copy Tower SA USB Flash Drive Duplicator User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 61 Aleratec manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							www.aleratec.com15
    Using the USB Duplicator
    4. Finish loading the blank target flash drives, then press the OK button 
    on the display panel.
    5. The LCD will display the status of the copying process.
    6. When Copy is complete LCD will display the following status:
    If the Copy fails, the LCD will display the number of flash drives that 
    failed and passed.
    7. When Copy is complete the Compare portion will automatically begin. 
    The LCD will display the status of the copying process.
    8. When Compare is complete the display will show the total, and the 
    number that pass and fail.
    Note: When Copy+Compare is in process the Green LED on the front 
    panel is blinking. Do not take out the drive while it is working. When 
    Copy+Compare is finished the Green LED stays on (no blinking). If an 
    error occurs during the process a Red LED will display. 
    ESC
    OK
    
    Copy   450M
    15% 0:32 68M
    ESC
    OK
    
    Compare    925M
    15% 0:18 226M
    ESC
    OK
    
    Total: 118/0
    Pass 118    Fail 0
    ESC
    OK
    
    Total: 3/0
    Pass 3   Fail 0          
    						
    							www.aleratec.com16
    Main Menu
    Asynchronous	Copy+Compare
    Asynchronous Copy+Compare is used only when the source content 
    is the same as or less than the system buffer (120MB). With the source 
    content read into the systems buffer you can copy and compare flash drives 
    continuously by taking out the drive which has finished its Copy+Repair 
    cycle, and replacing it with another blank. This process is repeated until the 
    Copy+Compare job is complete.    
    1. Load the source flash drive into the USB Duplicator. Use the UP or 
    DOWN arrow to scroll through the menu until Copy+Compare is 
    displayed on the LCD screen.  
    2. Press the OK button on the display panel. The USB Duplicator will 
    start to read the source content into the system’s buffer and immediately 
    start copying any loaded target USB flash drives.
    3. Load the blank target flash drives into the USB Duplicator. The LCD 
    will display the number of blank media loaded and copying.
    Note: When copying is in process the Green LED on the front panel is 
    blinking. Do not take out the drive while it is copying. When copying 
    is finished the Green LED stays on (no blinking). If an error occurs 
    during the copy process a Red LED will display. 
    USB(953M) 93M
    Reading...ESC
    OK
    
    ESC
    OK
    
    USB Duplicator
    3. Copy+Compare
    Pass: 0   Working
    Fail: 0    3ESC
    OK
            
    						
    							www.aleratec.com17
    Using the USB Duplicator
    4. If the Copy fails, the LCD will display the number of flash drives that 
    failed and passed.
    Note: During Asynchronous Copying you can use the UP and DOWN 
    arrow keys to check each flash drives copying status. 
    5. When Copy is complete the Compare portion will automatically begin. 
    The LCD will display the status of the copying process.
    6. When Compare is complete the display will show the total, and the 
    number that pass and fail.
    When Copy+Compare is finished with any of the target drives you 
    can take out the finished drive and put another blank flash drive for 
    Copy+Compare.  
    Note: When Copy+Compare is in process the Green LED on the front 
    panel is blinking. Do not take out the drive while it is working. When 
    Copy+Compare is finished the Green LED stays on (no blinking). If an 
    error occurs during the process a Red LED will display. 
    Pass: 5   Working
    Fail: 0    2ESC
    OK
    
    ESC
    OK
    
    Compare    93M
    15% 0:18 22M
    ESC
    OK
    
    Total:    3/0
    Pass 3   Fail 0        
    						
    							www.aleratec.com18
    Using the USB Duplicator
    Main Menu
    4. Capacity Check
    This function will check the capacity of each flash drive inserted. When 
    finished the following screen will appear. 
    Using the UP and DOWN arrows, you can scroll thru each drive 
    loaded to display capacity. 
    5. Information
    This function includes 2 subfunctions. These are: 
    5.1 USB Info
    5.2 System Info
    USB Duplicator
    5. Information
    OK
    ESC
    
    
    ESC
    OK
    
    4. Capacity Check
    Fail: 0   0
    ESC
    OK
    
    [#01] SIZE: 953M
     Capacity OK        
    						
    							www.aleratec.com19
    Using the USB Duplicator
    5.1	USB	Info.
    USB Info is a function that displays the USB flash drives basic information 
    such as flash type, content size, and available space.
    1. Use UP or DOWN arrow to scroll through the menu until Information 
    is displayed on the LCD screen. 
    Press the OK button to select or press ESC to go to the next setting.
    2. Press OK to get USB Info. You can scroll through each drive with 
    the arrow keys. Press ESC when finished. The LCD will display the 
    following status:
    5.2	System	Info.
    1. Use UP or DOWN arrow to scroll through the menu until System 
    Information is displayed on the LCD screen. 
    2. Press the DOWN arrow to get to System Info. and press OK.
    Press ESC twice to return to the Main Menu. 
    ESC
    OK
    
    5. Information
     1. USB Info
    ESC
    OK
    
    01  USB 953M
    FAT 16  925M
    ESC
    OK
    
    5. Information
     2. System Info        
    						
    							www.aleratec.com20
    Using the USB Duplicator
    Main Menu
    6. Utility
    The main menu Utility function has 6 subfunctions. These are:
    6.1 Format FAT 16/32
    6.2 Measure Speed
    USB Duplicator
    6. Utility
    OK
    ESC
    
    
    6.3 Media Check
    6.4 Quick Erase USB
    6.5 Full Erase USB
    6.6 System Update    
    						
    							www.aleratec.com21
    Using the USB Duplicator
    Main Menu
    6.1	Format	FAT	16/32
    This function is used to format flash drives with the duplicator. If the 
    original format is FAT 16/32, then the format operation will not change the 
    format, but will write over any data on the flash drive. 
    If the format is not FAT 16/32 (e.g. NTFS, Linux, or FAT multi-partition) 
    the controller will check the capacity of the flash drive. If the capacity is 
    greater than 2GB, it will automatically use FAT 32 format. If the capacity is 
    less than 2GB, it will use FAT 16.
    1. Load the flash drives into the USB Duplicator. Use the UP or DOWN 
    arrow to scroll through the menu until Utility is displayed on the LCD 
    screen.
    2. Use the UP and DOWN arrow keys to check the status of any of the 
    flash drives loaded in the machine. Drives inserted in the first port 
    (source) will not be formatted. 
    ESC
    OK
    
    USB Duplicator
    6. Utility
    ESC
    OK
    
    Do FORMAT
    Confirm?
    ESC
    OK
    
    [Utility]
    1. Format FAT        
    						
    							www.aleratec.com22
    Using the USB Duplicator
    6.2	Measure	Speed
    This function will measure the read and write speeds of drives loaded in the 
    ports. 
    1. Load drives. Use UP or DOWN arrow to scroll through the menu until 
    Utility is displayed on the LCD screen. Press the OK button to select or 
    press ESC to go to the next setting.
    2. Press OK and scroll to Measure Speed. The LCD will display the 
    following status:
    3. Use the UP and Down arrow keys to check each drive. 
    6.3	Media	Check
    This function is used to check flash drives with the controller. There are 
    2 types of checks that can be performed. Safe and Normal. The area to be 
    examined can be set for each check.
    1. Load drives. Use UP or DOWN arrow to scroll through the menu until 
    Utility is displayed on the LCD screen. Press the OK button to select or 
    press ESC to go to the next setting.
    ESC
    OK
    
    USB Duplicator
    6. Utility
    ESC
    OK
    
    [Utility]
    2. Measure Speed
    ESC
    OK
    
    [#2] Read: 21.7MB
     Write: 10.7 MB
    Port position
    ESC
    OK
    
    USB Duplicator
    6. Utility          
    						
    							www.aleratec.com23
    Using the USB Duplicator
    2. Press OK and scroll to Media Check. The LCD will display the 
    following status:
    3. Use UP or DOWN arrow to scroll through the available options:
    6.3.1	Safe	Check
    This function will read all the data on the flash drive with no writing so 
    as to preserve all of the data and format on the drive. Use the UP and 
    Down arrow keys to check the results on all of the drives loaded. 
    6.3.2	Normal	Check
    The controller will read and write in each area of the drive. If one of the 
    areas cannot be written to or read, the display will show an error. Use the 
    UP and Down arrow keys to check the results on all of the drives loaded.
    Note: All data and formats will be destroyed with the Normal Check.
    6.3.3	Setup	Range
    This function will adjust the percentage of the drive tested in the Safe 
    and Normal Checks. Use the Up and Down arrow keys to change the 
    percentage tested. 
    ESC
    OK
    
    [Utility]
    3. Media Check
    ESC
    OK
    
    [Media Check]
    1. Safe   100%
    (percentage of drive tested)
    ESC
    OK
    
    [Media Check]
    2. Normal   100%
    (percentage of drive tested)
    ESC
    OK
    
    [Media Check]
    3. Setup Range          
    						
    							www.aleratec.com24
    Using the USB Duplicator
    6.4	Quick	Erase	USB
    Quick Erase USB is a function that can quickly erase the target USB flash 
    drive. 
    Note: The Quick Erase USB function will only erase the FAT table 
    index of each target flash drives. 
     
    1. Use UP or DOWN arrow to scroll through the menu until Utility is 
    displayed on the LCD screen. Press the OK button to select or press 
    ESC to go to the next setting.
    2. Press OK and scroll to Quick Erase USB. The LCD will display the 
    following status:
    3. Press OK to select. The LCD will display the following status:
    Press OK for Yes or ESC for No. 
    4. LCD display will show the following screen when finished.
    Note: This function will erase the flash drive’s data content. It will not 
    erase the flash drive’s FAT 16/32 format. If the format of the target 
    drive is not FAT 16/32, the Quick Erase won’t execute.
    ESC
    OK
    
    USB Duplicator
    6. Utility
    ESC
    OK
    
    6. Utility
    1. Quick Erase USB
    ESC
    OK
    
    Do Erase All
    Confirm?
    ESC
    OK
    
    Pass: 2 Working
    Fail: 0  0          
    						
    All Aleratec manuals Comments (0)

    Related Manuals for Aleratec 1118 USB Copy Tower SA USB Flash Drive Duplicator User Guide