Aleratec 111 HDD Copy Cruiser 11 Hard Disk Drive Duplicator and 12 HDD Sanitizer User Guide

							www.aleratec.com5
Precautions
Before installing your 1:11 HDD Copy Cruiser, please read the following.
Installation
Avoid placing the 1:11 HDD Copy Cruiser in a location subject to:
• High humidity
• High temperature
• Excessive dust
• Mechanical vibration
• Direct sunlight
• Electromagnetic radiation
Power
This product has a manually switchable power supply. Make	sure	that	the	power	
supply	is	set	to	the	proper 	voltage	for	your	region.
Choose a Good Location
1. Allow adequate clearance for moving parts.
2. Do not place near heat sources such as radiators or air ducts, or in a place 
subject to direct sunlight, excessive dust, mechanical vibration or shock.
3. Disconnect the AC adapter from the outlet if the product is not used for an 
extended period of time. 
4. Proper care will help assure maximum product life. Improper operating 
environment and misuse may void the warranty. 
Operation
Do not move the 1:11 HDD Copy Cruiser during operation. This may cause a 
malfunction or other undesirable results.
Avoid exposing the unit to sudden changes in temperature as condensation may form 
inside the 1:11 HDD Copy Cruiser. Should the surrounding temperature suddenly 
rise while the 1:11 HDD Copy Cruiser is on, wait at least one hour before turning 
off the power. Operating the duplicator immediately after a sudden increase in 
temperature may result in a malfunction.
Transportation
Keep the original packing materials for future moving or shipping of the 1:1 1 HDD 
Copy Cruiser.  
						

							www.aleratec.com6
Overview
Power Up Sequence
During the normal power-up sequence of the 1:11 HDD Copy Cruiser, the following 
information will be displayed.
• Figure 1 shows the firmware version
• Figure 2 shows the memory initialization
• Figure 3 shows the scanning of the drives
• Figure 4 shows the number of drives loaded. 
• Figure 5 shows the first function. 
ENTESC


HDD Cruiser2061F ver:A.23P
Initialize SDRAMENTESC


Detect DrivesPlease wait...ENTESC


Detect DrivesFound 0 DevicesENTESC


1. Copy HDDENTESC

  
						

							www.aleratec.com7
Overview
Main Menu
There are eleven main menu items that can be seen in the 1:11 HDD Copy Cruiser 
Copy Controller Display Panel. These are:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10. 
 
 
11.
 Note: The Advanced Setup function is a hidden menu. To access this menu, press ESC for 3 seconds. After you have completed any desired adjustments, press ESC to exit Advanced Setup.
1. Copy HDD
2. Async Copy
3. Compare HDD
4. Async Compare
5. PreScan Source
6. ReScan Bus
7. Source size
9. Overwrite
10. Setup
11. Adv Setup
8. Secure Erase  
						

							www.aleratec.com8
Overview
Subfunctions
The “Setup” menu has 13 subfunctions. These are:
ENTESC


10. Setup
Language
Copy Size
Startup Menu
Auto Compare
Button Sound
Device Info
System Info
Fast Copy
Auto Start Drive(Not Supported)
Tolerance Size
Boot Time Delay
Quick Compare
Auto Start Timer(Not Supported)  
						

							www.aleratec.com9
Overview
The “Advanced Setup” menu has nine subfunctions. These are:
Read Error Skip
Update Firmware
Compare Firmware
Quick Erase HDD
Full Erase
H/W Diagnostic
Load Default
Copy HPA
Burn In
ENTESC


11. Adv Setup  
						

							www.aleratec.com10
Using the 1:11 HDD Copy Cruiser 
Loading the Hard Drives
1. Open the drive tray doors by lifting the tab on the left side of each drive bay 
you wish to use.  
2. Take the Hard Disc Drive (HDD) and align the drive’s SATA plug to the lower 
right hand side of the drive bay. 
3. Slide the HDD into the drive bay until it stops. The drive will still be about 1 
inch outside of the bay. When the door is closed it will push and plug the HDD 
into the duplicator.
4. Swing the drive bay door closed and press the left side of the door until the tab 
latches. When it latches, a click can be felt and heard. 
Note: If you are duplicating, the source hard disk drive goes in the top bay.
Source Drive
Target Drives  
						

							www.aleratec.com11
Using the 1:11 HDD Copy Cruiser 
Removing Hard Drives
1. Open the drive tray doors by pulling the handle/tab on the left side of each 
drive tray door. 
Note: Do not attempt to remove the hard drive if the drive activity LED is on.
2. To disengage the HDD, swing the drive tray door to the full open position. 
3. Pull drive forward and remove drive.  
						

							www.aleratec.com12
Using the 1:11 HDD Copy Cruiser 
Main Menu
Copy HDD
The “Copy HDD” function performs an actual copy from a source HDD to one or 
more target HDDs. The target HDDs must be at least as large as the source. The 1:11 
HDD Copy Cruiser will copy every block of capacity on the source HDD. 
1. Load the source HDD and the target HDDs into the 1:11 HDD Copy Cruiser. 
The system will auto-detect the hard drives. After the drives have been 
detected, a screen similar to the one below will be displayed. 
Note: Before copying be sure that the capacity of the target HDD is equal to or larger than the source hard drive. 
2. Press ENT to start copying. The system will auto-detect the hard drives. The 
following information will be displayed. 
3. During the copy process the 1:11 HDD Copy Cruiser will display progress 
information.
The amount of data remaining to be transferred (shown in gigabytes), and time 
will be displayed as the percentage of completion increases. 
Note: The copying speed, capacity and duration may vary from one source hard drive to another. 
ENTESC


1. Copy HDD149.1GB
ENTESC


Detect DrivesPlease wait...
ENTESC


Copy- 36MB/s 0%235.7GB 1:48  
						

							www.aleratec.com13
Using the 1:11 HDD Copy Cruiser 
4. Once duplication is complete, a job status screen will be displayed.
ENTESC


1. Copy HDDOK:1 Fail: 0  
						

							www.aleratec.com14
Using the 1:11 HDD Copy Cruiser 
Main Menu
Async Copy
The function “Async Copy” allows you to insert target drives during the copying 
operation. During the process, you can insert another drive as a target of the Async 
Copy operation and the unit will automatically copy to this new drive as well.  
1. Load the source HDD and the target HDDs into the 1:11 HDD Copy Cruiser. 
The system will auto-detect the hard drives. After the drives have been 
detected, a screen similar to the one below will be displayed. 
Note: Before copying be sure that the capacity of the target HDD is equal to or larger than the source hard drive. 
2. Press ENT to start copying. The system will auto-detect the hard drives. The 
following information will be displayed. 
3. During the copy process the 1:11 HDD Copy Cruiser will display progress 
information.
The amount of data remaining to be transferred (shown in gigabytes), and time 
will be displayed as the percentage of completion increases. 
Note: The copying speed, capacity and duration may vary from one source hard drive to another. 
ENTESC


2. Async Copy
ENTESC


Detect DrivesPlease wait...
ENTESC


Copy- 36MB/s 0%235.7GB 1:48