Home > Aleratec > Hard Disk > Aleratec 11 HDD PortaCruiser Hard Disk Drive Duplicator and RAID User Guide

Aleratec 11 HDD PortaCruiser Hard Disk Drive Duplicator and RAID User Guide

    Download as PDF Print this page Share this page

    Have a look at the manual Aleratec 11 HDD PortaCruiser Hard Disk Drive Duplicator and RAID User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 61 Aleratec manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							www.aleratec.com35
    Using the HDD PortaCruiser 
    Duplicator Mode
    Advanced Setup Menu: 8-05 Load DefaultThis function is used to restore all factory settings of the HDD PortaCr\
    uiser 
    back to their original defaults. 
    Press and hold 
    1.  ESC for about three seconds to access the “Adv Setup” 
    menu. The following screen will be displayed. 
    Use the arrow buttons (
    2.  or) to select “Load Default”. The following 
    screen will be displayed. 
    Press 
    3.  ENT to proceed to the following screen:
    Press ENT to confirm loading defaults, or press  ESC to cancel.
    When all settings are restored to their original defaults the following \
    4. 
    information will be displayed. 
    ENT
    8. Adv Setup
    ESC
    RESET
    MUTE
    
    ENT
    8-05. Adv Setup
    Load Default
    ESC
    RESETMUTE
    
    ENT
    Load Default
    Config? Yes
    ESC
    RESETMUTE
    
    ENT
    Load Default
    OK
    ESC
    RESETMUTE
     
    						
    							www.aleratec.com36
    Using the HDD PortaCruiser 
    Duplicator Mode
    Advanced Setup Menu: 8-06 Link OptionThis function is used to decide if  “7.USB RAID Mode” will be disp\
    layed in the 
    display panel.  
    Press and hold 
    1.  ESC for about three seconds to access the “Adv Setup” 
    menu. The following screen will be displayed. 
    Use the arrow buttons (
    2.  or) to select “Link Option”. The following 
    screen will be displayed. 
    Press 
    3.  ENT to display the available options. The default is “Menu ON” 
    which specifies for “7.USB RAID Mode” to appear in the main menu.
    If set to “OFF”, “7.USB RAID Mode” will not appear in the ma\
    in menu. 
    After changing a setting, remember to press  ENT to save it. 
    ENT
    8. Adv Setup
    ESC
    RESET
    MUTE
    
    ENT
    8-06. Adv Setup
    Link Option
    ESC
    RESETMUTE
    
    ENT
    Link Option
    Menu ON
    ESC
    RESETMUTE
     
    						
    							www.aleratec.com37
    Using the HDD PortaCruiser 
    Duplicator Mode
    Advanced Setup Menu: 8-07 USB Auto-LinkThis function sets the HDD PortaCruiser to immediately enter Dual Disk R\
    AID 
    Controller (USB) mode on startup. This allows direct control of the unit 
    from a 
    PC. 
    Press and hold 
    1.  ESC for about three seconds to access the “Adv Setup” 
    menu. The following screen will be displayed. 
    Use the arrow buttons (
    2.  or) to select “USB Auto-Link”. The following 
    screen will be displayed. 
    Press 
    3.  ENT to display the available options. The default is “OFF”.
    Use the arrow buttons (
    4.  ) to toggle the option “ON” or “OFF”. If 
    set to “ON” the unit will immediately enter USB mode on startup. After 
    changing a setting, remember to press  ENT to save it. 
    ENT
    8. Adv Setup
    ESC
    RESET
    MUTE
    
    ENT
    8-07. Adv Setup
    USB Auto-Link
    ESC
    RESETMUTE
    
    ENT
    USB Auto-Link
    OFF
    ESC
    RESETMUTE
    
    ENT
    USB L.H Mode
    D1:HDD  D2:HDD
    ESC
    RESET
    MUTE
     
    						
    							www.aleratec.com38
    Using the HDD PortaCruiser 
    Duplicator Mode
    Advanced Setup Menu: 8-08 Copy HPA
    If the source hard disk contains a Host Protected Area (HPA), this option allows 
    you to choose whether or not to copy data within the HPA. Press and hold 
    1.  ESC for about three seconds to access the “Adv Setup” 
    menu. The following screen will be displayed. 
    Use the arrow buttons (
    2.  or) to select “Copy HPA”. The following 
    information will be displayed. 
    Press 
    3.  ENT to display the current configuration setting. A screen similar to 
    the following will be displayed. 
    Use the arrow buttons (
    4.  ) to toggle the option “On” or “Off”. After 
    changing a setting, remember to press  ENT to save it. 
    Note: The HPA is a hidden data region defined in ATA/ATAPI-4. This area is 
    not usually accessible to the operating system or software applications.\
     The 
    HDD PortaCruiser supports the copying of data from this hidden area.
    ENT
    8. Adv Setup
    ESC
    RESET
    MUTE
    
    ENT
    8-08. Adv Setup
    Copy HPA
    ESC
    RESETMUTE
    
    ENT
    Copy HPA
    Off
    ESC
    RESETMUTE
     
    						
    							www.aleratec.com39
    Using the HDD PortaCruiser 
    Dual Disk RAID Controller (USB) Mode
    Main Menu: Duplicator Mode Option 
    This function allows you to switch to the Duplicator mode. 
    Use the arrow buttons (
    1.  or) to select “Duplicator Mode”. The 
    following screen will be displayed.
    Press 
    2.  ENT to select. The system will prompt you to confirm that you wish 
    to change modes. 
    Use the arrow buttons (
    3.  ) to select “Yes” and press ENT to select. The 
    following screen will be displayed. The unit is now back in Duplicator 
    Mode. 
    ENT
    Back to Stand Alone Mode?
    No
    ESC
    RESET
    MUTE
    
    ENT
    Duplicator Mode
    ESC
    RESETMUTE
    
    ENT
    1. Copy HDD
    Copy Size
    ESC
    RESETMUTE
     
    						
    							www.aleratec.com40
    Using the HDD PortaCruiser 
    Dual Disk RAID Controller (USB) Mode
    Main Menu: Information Option
    This function displays information about the HDD PortaCruiser and any 
    attached hard drives.Use the arrow buttons (
    1.  or) to select “Information”. The following 
    screen will be displayed.
    Press 
    2.  ENT to select.  The system will prompt you to choose the desired 
    device.
    Use the arrow buttons (
    3.  or) to select between System, Drive1 and 
    Drive2 and press ENT to select.  
    For System information, USB Mode and firmware version will be 
    displayed.
    For Drive information, drive model information and capacity will be 
    displayed.
    ENT
    Information
    ESC
    RESET
    MUTE
    
    ENT
    Information
    System
    ESC
    RESETMUTE
    
    ENT
    USB Mode:   Normal
    F/W ver:   092C
    ESC
    RESET
    MUTE
    
    ENT
    Hitachi HD572168
    Capacity: 76.3GB
    ESC
    RESETMUTE
     
    						
    							www.aleratec.com41
    Using the HDD PortaCruiser 
    Dual Disk RAID Controller (USB) Mode
    Main Menu: Change RAID Mode OptionThis function allows you to choose the RAID mode for the Dual Disk RAID \
    Controller.
    Use the arrow buttons (
    1.  or) to select “Change RAID Mode”. The 
    following screen will be displayed. 
    Press 
    2.  ENT to select. The system will prompt you to choose the desired 
    mode.  
    Use the arrow buttons (
    3.  ) to select between Normal, JBOD, RAID0, 
    and RAID1, and press ENT to select.  
    Changing to Normal Mode
    The system will prompt you to confirm that you wish to change 
    4. 
    modes.
    Use the arrow buttons (
    5.  or) to select “Yes” and press ENT 
    to select. The system will then prompt you to confirm that you 
    understand data may be lost.
    ENT
    Change RAID Mode
    RAID0
    ESC
    RESET
    MUTE
    
    ENT
    Change RAID Mode
    ESC
    RESETMUTE
    
    ENT
    Change to Normal Mode?
    No
    ESC
    RESETMUTE
    
    ENT
    Data May Be Lost
    Continue?  No
    ESC
    RESET
    MUTE
     
    						
    							www.aleratec.com42
    Using the HDD PortaCruiser 
    Dual Disk RAID Controller (USB) Mode
    Main Menu: Change RAID Mode Option
    Changing to Normal Mode - continued Use the arrow buttons (
    6.  ) to select “Yes” and press ENT to select.  
    The new main screen will be shown which displays the new mode 
    and capacity.  
    Changing to JBOD Mode The system will prompt you to confirm that you wish to change 
    4. 
    modes.
    Use the arrow buttons (
    5.  or) to select “Yes” and press ENT 
    to select. The system will then prompt you to confirm that you 
    understand data may be lost.
    Use the arrow buttons (
    6.  ) to select “Yes” and press ENT to select.  
    The new main screen will be shown which displays the new mode 
    and capacity.  
    ENT
    USB Mode: Normal
    D1:HDD  D2:HDD
    ESC
    RESET
    MUTE
    
    ENT
    Change to JBOD Mode?
    No
    ESC
    RESETMUTE
    
    ENT
    Data May Be Lost
    Continue?  No
    ESC
    RESET
    MUTE
    
    ENT
    USB Mode: JBOD
    RAID Cap: 228.9GB
    ESC
    RESETMUTE
     
    						
    							www.aleratec.com43
    Using the HDD PortaCruiser 
    Changing to RAID0 ModeThe system will prompt you to confirm that you wish to change modes.
    4. 
    Use the arrow buttons (
    5.  or) to select “Yes” and press ENT to select. 
    The system will then prompt you to confirm that you understand data may 
    be lost.
    Use the arrow buttons (
    6.  ) to select “Yes” and press ENT to select.  
    The new main screen will be shown which displays the new mode and 
    capacity.
    Changing to RAID1 Mode The system will prompt you to confirm that you wish to change modes.
    4. 
    Use the arrow buttons (
    5.  ) to select “Yes” and press ENT to select.  
    The system will then prompt you to confirm that you understand data may 
    be lost.
    ENT
    Data May Be Lost
    Continue?  No
    ESC
    RESET
    MUTE
    
    ENT
    Data May Be Lost
    Continue?  No
    ESC
    RESET
    MUTE
    
    ENT
    USB Mode: RAID0
    RAID Cap: 152.6GB
    ESC
    RESETMUTE
    
    ENT
    Change to RAID1 Mode?
    No
    ESC
    RESETMUTE
    
    ENT
    Change to RAID0 Mode?
    No
    ESC
    RESETMUTE
     
    						
    							www.aleratec.com44
    Using the HDD PortaCruiser 
    Dual Disk RAID Controller (USB) Mode
    Main Menu: Change RAID Mode Option
    Changing to RAID1 Mode - continued 
    Use the arrow buttons (
    6.  ) to select “Yes” and press ENT to select.  The 
    system will then ask you whether or not you want to preserve the Source \
    drive’s data.
    If you would like to keep the Source drive’s data, use the arrow 
    7. 
    buttons () to select “Yes” and press ENT to select. The device 
    will copy the source drive’s data to the target drive and a new main 
    screen will be shown which displays the new mode and capacity.
    ENT
    Keep Source Data?
    No
    ESC
    RESET
    MUTE
    
    ENT
    USB Mode: RAID1
    RAID Cap: 76.3GB
    ESC
    RESETMUTE
     
    						
    All Aleratec manuals Comments (0)

    Related Manuals for Aleratec 11 HDD PortaCruiser Hard Disk Drive Duplicator and RAID User Guide