Home > Alarm Lock > Alarm Lock > Alarm Lock ALDTMIII CHANGES FOR THE PL3000 PL3500 User Manual

Alarm Lock ALDTMIII CHANGES FOR THE PL3000 PL3500 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Alarm Lock ALDTMIII CHANGES FOR THE PL3000 PL3500 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 84 Alarm Lock manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							 
     
     
     
     
     
     
     
     
     
    AL-DTM-III  PROCEDURAL 
    CHANGES FOR THE 
    PL3000 / PL3500 
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     The procedure below is required only when a PC or DTM communication 
    Function Card is not presently enrolled in the lock; i.e. the lock is new (out-of-
    box), or the lock has had all programming erased (restoring factory default). 
     
    PC/DTM Communications 
    Previous versions of the AL-DTM did not require the 299 code (Function Card 
    #2) to be presented twice; the AL-DTM-III does require Function Card #2 to be 
    presented twice, and therefore the AL-DTM 299 Function Card #2 must be 
    enrolled into the lock prior to using the AL-DTM-III.   
     
    Note:  When using the new PL3500 with DL-Windows 3.5 (or higher), the AL-
    DTM-III must be used.  Direct PC communications is not currently supported, 
    and the PL3500 must be setup as a PL3000 lock-type in DL-Windows 3.5 (or 
    higher). 
     
    Procedure: 
    All lock programming MUST be erased to restore the out of box factory de-
    fault, as follows:  
    PL3000: 
    Follow the Erase All Programming instructions in the Wiring and Power 
    Up section in WI1280, in which the shunt connector is plugged into the 
    yellow wire connector. 
     
    PL3500:  
    Power up the lock, wait and listen for three beeps, then hold down the out-
    side lever. 
     After erasing all lock programming, both lock models wait for a proximity card to 
    be presented.  Therefore, present a proximity card (to place the lock into learn 
    mode), then immediately present the first two Function Cards (card #1 for initi-
    ating PC communications, card #2 for initiating AL-DTM communications).  Af-
    ter cards #1 and 2 have been presented and enrolled, wait for the lock to time-
    out and lock.  Now the PL3000 can be programmed by the PC or the AL-DTM-III.  Currently, 
    the PL3500 can only be programmed by the AL-DTM-III; the PL3500 is not sup-
    ported by DL-Windows at this time.    
     
     
     
     
     
     
     
     
     
     
     
     © ALARM LOCK 2006                                                                            WI1457A  3/06
     
    345 Bayview Avenue 
    Amityville, New York 11701 
    For Sales and Repairs 1-800-ALA-LOCK 
    For Technical Service 1-800-645-9440 
     
    Publicly traded on NASDAQ             Symbol: NSSC
     
     
     
     
     
     
     
     
     
     
     
    AL-DTM-III  PROCEDURAL 
    CHANGES FOR THE 
    PL3000 / PL3500 
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     The procedure below is required only when a PC or DTM communication 
    Function Card is not presently enrolled in the lock; i.e. the lock is new (out-of-
    box), or the lock has had all programming erased (restoring factory default). 
     
    PC/DTM Communications 
    Previous versions of the AL-DTM did not require the 299 code (Function Card 
    #2) to be presented twice; the AL-DTM-III does require Function Card #2 to be 
    presented twice, and therefore the AL-DTM 299 Function Card #2 must be 
    enrolled into the lock prior to using the AL-DTM-III.   
     
    Note:  When using the new PL3500 with DL-Windows 3.5 (or higher), the AL-
    DTM-III must be used.  Direct PC communications is not currently supported, 
    and the PL3500 must be setup as a PL3000 lock-type in DL-Windows 3.5 (or 
    higher). 
     
    Procedure: 
    All lock programming MUST be erased to restore the out of box factory de-
    fault, as follows:  
    PL3000: 
    Follow the Erase All Programming instructions in the Wiring and Power 
    Up section in WI1280, in which the shunt connector is plugged into the 
    yellow wire connector. 
     
    PL3500:  
    Power up the lock, wait and listen for three beeps, then hold down the out-
    side lever. 
     After erasing all lock programming, both lock models wait for a proximity card to 
    be presented.  Therefore, present a proximity card (to place the lock into learn 
    mode), then immediately present the first two Function Cards (card #1 for initi-
    ating PC communications, card #2 for initiating AL-DTM communications).  Af-
    ter cards #1 and 2 have been presented and enrolled, wait for the lock to time-
    out and lock.  Now the PL3000 can be programmed by the PC or the AL-DTM-III.  Currently, 
    the PL3500 can only be programmed by the AL-DTM-III; the PL3500 is not sup-
    ported by DL-Windows at this time.    
     
     
     
     
     
     
     
     
     
     
     
     © ALARM LOCK 2006                                                                             WI1457A  3/06
     
    345 Bayview Avenue 
    Amityville, New York 11701 
    For Sales and Repairs 1-800-ALA-LOCK 
    For Technical Service 1-800-645-9440 
     
    Publicly traded on NASDAQ             Symbol: NSSC
      
    						
    All Alarm Lock manuals Comments (0)

    Related Manuals for Alarm Lock ALDTMIII CHANGES FOR THE PL3000 PL3500 User Manual