AirStar Light Sirocco User Manual

 02-07-2012 / 65-63-072 B  1       Models Covered: 2K HA / 4K HA 600 HI-CR 1.2K HMI / 2.5K HMI 1K HI-BT37                 Mode d’emploi Owner’s Manual Instrucciones de uso 10255 General Drive • Unit A6  • ORLANDO, FL 32824 • USA Tel: (407)851-7870 • Fax: (407)851-7831 www.airstar-light.us • e-mail : [email protected]    NAFTA  

 02-07-2012 / 65-63-072 B  2 Welcome To Airstar  Thank you for choosing AIRSTAR. Your new Sirocco unit is hand assembled with pride in USA, and we are committed to your total customer satisfaction.  Your ownership experience is extremely important to us and this user manual is designed to help keep your Sirocco performing at its highest level.  Let There Be Light  Your Sirocco is specifically designed to provide the highest quality light for nighttime workplace safety and productivity.  It is perfect for...

 02-07-2012 / 65-63-072 B  3 Tips To Extend The Life Of Your Sirocco Unit  1.Use the included glove when handling lamps to prevent potential damage caused by transfer of oils and dirt to glass. 2.Always disconnect from power source before performing service. 3.Do not operate your Sirocco without its envelope or with a damaged envelope. 4.Protect the envelope by operating away from walls, projectiles, electric wires, trees, animals, etc. 5.DO NOT LEAVE DEFLATED ENVELOPE UNCOVERED OR UNATTENDED WHEN NOT IN...

 02-07-2012 / 65-63-072 B  4 a e d b c 14 Sirocco Parts List                                     1 Nut 2 Internal Structure (Cage + Base + Support Stem) 3 Envelope 4 Power Supply Cable 5 Zipper 6 Lamp(s) (See Lamp Variations – Pictured Above) a HA 1000W R7S lamp b HCI-T/P 150W E27 lamp M102/O 150W MEDIUM lamp c HMI 1200W G38 lamp d HMI 2500W G38 lamp e HI-BT37 1000W E39 ANSI lamp 7 South Pole Plate 8 Stand (Recommended Accessory. Sold separately.) 9 Repair Kit (2 Pieces) 10 Protective Storage Cover 11...

 02-07-2012 / 65-63-072 B  5 Envelope Installation Instructions  · When REPLACING an old envelope, FIRST remove original envelope: · If currently in use, first turn unit off and let cool. · Unplug the Sirocco unit and open the envelope zipper. · Unscrew the nut on the top of the envelope. (Fig. 1) Set top nut in a secure place. · Maneuver top of cage to unzipped opening and pass the cage through until fully exposed. · Unhook the lamp holder springs (Fig. 2 – only select Sirocco models) · Remove lamp(s)...

 02-07-2012 / 65-63-072 B  6 Lamp Replacement Instructions  · Sirocco 2K (HA 2x1000W) – (Fig. 1) & Sirocco 4K HA (HA 4x1000W) – (Fig. 2)  · Unplug the Sirocco unit and open the envelope zipper. (Be sure to let unit cool.) · Using a glove, remove old lamps by applying downward pressure and sliding the top of the lamp out of the fixture, then lifting the lamp up and out of the fixture. · Insert new lamps by inserting bottom of lamp into fixture, applying downward pressure, and then sliding top of lamp into...

 02-07-2012 / 65-63-072 B  7 Lamp Replacement Instructions (cont.)  · Sirocco 1.2K (HMI 1200W) · Unplug the Sirocco unit and open the envelope zipper. (Be sure to let unit cool.) · Unhook the lamp holder springs and place lamp holder aside. (Fig. 1)                · Using a glove, remove the old lamp and replace with new lamp. (Fig. 4) · Replace lamp holder and hook springs over the edge and up through lamp support plate. (Fig. 2) · Close the zipper.    · Sirocco 2.5K  (HMI 2500W) · Unplug the Sirocco...

 02-07-2012 / 65-63-072 B  8 Lamp Replacement Instructions (cont.)  · Sirocco 1K (HI-BT37 1000W) · Unplug the Sirocco unit and open the envelope zipper. (Be sure to let unit cool.)  · Unscrew the top-nut at the top of the envelope and set nut safely aside. (Fig. 1) · Lift envelope off of the north pole pin and carefully slide unzipped envelope opening down around cage, toward south pole plate. · Unscrew the nylon thumb wheels at the base of the lamp that secure the included “wrench”. (Fig. 2) · Using the...

 02-07-2012 / 65-63-072 B  9 In The Event Of Broken Lamp(s)  If a lamp breaks or cracks inside the envelope, disconnect the electrical power supply and disassemble the envelope. (see Envelope Installation Instructions)  Be sure to remove all fragments of glass, using a vacuum cleaner to thoroughly clean the electronics and envelope. Use extreme caution when handling glass fragments to avoid injury.  Installing Your Sirocco On A Stand  NOTE:   · Always use Airstar-approved stands designed to work with...

 02-07-2012 / 65-63-072 B  10 When Operating Ballast Powered Sirocco Units  · Sirocco models that require a ballast: Sirocco 1K, Sirocco 1.2K, Sirocco 2500, and Sirocco 4K.  · ALWAYS PLUG SIROCCO UNIT INTO BALLAST BEFORE CONNECTING TO POWER OUTLET - Connect the Sirocco power cable to the ballast. - Securely lock the power cable connector to ballast socket. - Connect ballast to appropriate power supply. - Reverse procedure when shutting down your Sirocco unit.               Maintenance  · Lamp · It is...