Air Oasis nano Induct User Manual

For use with models: NIND14, NIND9, NIND6
For safety and to ensure proper use carefully read the contents of this manual before operating or installing  the unit.
NANO INDUCT
Owner’s Manual  

Thank You for Choosing The nano Induct Sanifier®!
Congratulations,  you  own  the  most  advanced  induct  air  purifier  available!  Before 
operating the nano Induct™  please read this manual in its entirety.  Doing so will 
give you important information to keep you safe from harm and ensure you get the 
most benefits from your Sanifier®. For additional information please contact us:
mail:  Air Oasis, LLC
 Attn: Customer Service
 3401 Airway Blvd.
 Amarillo, TX 79118
web: www.airoasis.com
e-mail:...

Important Safety Instructions
When operating any electrical appliance, basic precautions should always be fol-
lowed for safety. 
 RISK OF FIRE, ELECTRIC SHOCK, OR INJURY
• Carefully read the entire contents of this manual.
• Do not use outdoors, in moist areas or on wet surfaces.
• Do not use the unit in areas of extreme heat or in the pres-
ence of flammable gas.
• Do not allow any foreign objects to enter the ballast cooling 
vents. 
• Do not attempt to service or repair the unit yourself. Any at-...

Status Indicator Lights
The  nano  Induct  contains  a  smart  ballast  which  provides  a  warm-up  period  then 
checks for correct operation and continuously watches for any fault condition.  
Lamp startup is a controlled process.  First the lamp is preheated using the internal 
filaments for a preheat duration of less than 4 seconds.  Once the preheating pe-
riod is over the bulb should be lit.  After 8 seconds the bulb is continuously checked 
for correct operation.  Should a fault be detected the...

Power Adapter
The nano Induct is powered using a 26 VDC power adapter with a rated input volt-
age of 100 - 240 VAC.  The adapter connects to a 110 or 230 VAC 3 amp power 
cord. For your safety and to ensure proper function of your nano Induct we recom-
mend that ONLY the power adapter included with the original purchase be used.
Placement and Installation
Placement Suggestions
The nano Induct units are designed to be installed within the duct of an HVAC sys-
tem. We recommend they be mounted on the...

Preparing to Install
The nano Induct was designed to be simple and effective. Remove the unit, power 
adapter, power cord, and mounting hardware from the box. We recommend keep-
ing the box and all packaging material for shipping the unit should it ever need to 
be returned for repairs.
Installation Instructions 
Installation  and  servicing  of  air-conditioning  equipment  can  be  hazardous  due  to 
system  pressure  and  electrical  components.  Only  trained  and  qualified  service 
personnel...

3.  Clean  a  one  inch  area  around  the  hole  where  the  NIND  will  be  mounted.  Re-
move the wax paper from the gasket.  Insert the NIND into the 3 3/4” \
hole, aligning 
the cross hairs parallel to the duct. Press firmly on the Retainer Ring to adhere the 
gasket to the duct.
4. If installing on fiberglass duct board place aluminum tape ring over the Retainer 
Ring to help secure the unit. 
5. Firmly press the Ballast Assembly onto the four pins protruding from the AHPCO 
Cell.  The  Ballast...

Air Flow Label
Ballast Assembly
6.  Secure  the  NIND  with  four  self  tapping  3/4”  screws  being  careful  not  to  over-
tighten.
7. Secure the power adapter with included self tapping 1/2” screws.
8. Adhere the two included warning labels in close proximity to the NIND device. 
6
CAUTIONDO NOT LOOKAT UV LIGHT
CAUTIONWARNING!!Eye damage may result from directly viewing 
the light produced by these lamps.To reduce the risk of exposure to UV-radiation, take UV-radiation 
protective measures for...

Plug the included power adapter into the nano Induct.  Connect the power adapter 
to  a  110  or  240  VAC  electrical  outlet.  The  unit  will  start,with  the  green  and  blue 
lights illuminating. It’s designed for continuous operation. For maximum effective-
ness, operate the unit 24 hours a day, 7 days a week. 
Optional 24 VAC Internal HVAC Power Source Wiring
When  wiring  direct  to  24V  we  strongly  recommend  installing  a  separate  40  VA 
transformer to ensure optimal performance and...

Maintenance
AHPCO® Cell Replacement Process
The  entire  Cell  should  be  replaced  every  two  years.  Failure  to  replace  the  Cell 
will  decrease  the  effectiveness  of  the  unit. After  two  years  of  use  the  blue  Lamp 
Replacement light will begin to blink as a reminder that it’s time to replace the AH-
PCO® Cell. 
Note: UV lamps contain Hg (Mercury) and should be disposed of according to dis-
posal laws. Find disposal centers at www.earth911.org.
We recommend contacting a licensed HVAC...