Aiphone JPDVFRP10 Instructions User Manual

							JP-DVF-RP10
Vandal Resistant Color Video Door Station
with Built in HID
® multiCLASS SE® Card Reader
-INSTRUCTIONS-
The JP-DVF-RP10 is a JP Series color video door station with a multiCLASS SE
® card reader built 
onto the same stainless steel faceplate. The card reader provides electronic access to a building 
through a separate Access Control System, which is not supplied by Aiphone.
NAMES & FUNCTIONS: 
1.  Camera      5.  Directory card 
2.  Microphone    6.  Call button 
3.  LED illuminator    7.  multiCLASS reader 
4.  Speaker
FEATURES: 
•  All-in-one solution - Communication product & 
card reader  
•  If a card is missing or malfunctioning, audio/video 
communication can provide user verification  
•  Standard Wiegand output to access panel  
•  Convenience of installing combined components
JP-DVF-RP10
OPTIONAL ACCESSORIES: 
• SBX-ISDVFRA - Surface mount stainless steel  
   backbox
INSTALLATION: 
• For flush mounting, cut a hole in the wall and use 
supplied back box.  
Box dimensions are:  
11-1/16” H x 5-13/16” W x 1-3/4” D 
•  For surface mounting, use the SBX-ISDVFRA 
surface mount box. This box can mount to a 
standard 1-gang box or to any flat surface.
PACKAGE CONTENTS:
JP-DVF-RP10
Vandal-resistant Door Station Security Driver
Blank name  placard Back box 
& tamper-resistant screws
1
2
3
4
5
6
7 
						

							WIRING DIAGRAM:
1A11A2
2A12A2
3A13A2
4A14A2
+-
A1A2
+-
JP-DVF-RP10JP-4MED
PS-2420UL
TESTING & OPERATION:
• When power is applied to the card reader, the LED will flash green three (3) times while the 
beeper beeps simultaneously. The LED will then turn red. This indicates that the microcontroller is 
operating properly. 
•  Present an ID card to the reader (hold card directly in front of reader).  The LED will momentarily 
turn green while the beeper beeps once, indicating that the card was rea\
d successfully.
SPECIFICATIONS:
CARD READER:
Reader type:    RP10
Power Source:  5 ~ 16V DC
Current:    75mA (Avg); 200mA (peak)
Terminations:    Color-coded pre-wired pigtail
Wiring Distance:  500’
Operating Temp:  -31° ~ 150°F / -35° ~ 65°C
Operating Humidity:  0-95% relative humidity
   non-condensing CAMERA:
Camera unit:   
CMOS camera
Scanning line:   525 lines
Min. illumination:  5 Lux at 1’6”
Terminations:    Screw terminals
Operating Temp:  14° ~ 140°F / -10° ~ 60°C
Wiring Distance:  330’ w/ 871802 wire
Dimensions:    11-11/16” H x 7” W
FCC WARNING:This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1)  This device may not cause harmful interference.
(2)  This device must accept any interference that may cause undesired operation.
• For proper regulatory compliance, the drain wire should be disconnected \
at the power 
supply end of the cable.
•  Changes or modifications not expressly approved by the party responsible for 
compliance could void the user’s authority to operate the equipment.
•  The Reader is intended to be powered from a limited power source output \
of a 
previously certifed power supply
Aiphone Corporation  |
  www.ai phone.co m/home  |
  [email protected] m |
  P:  80 0.69 2.02 00
Pg. 2
JP-DVF-RP10 Instr. 0715
Pigtail Discription
Yellow Beeper Input
Orange  Green (GRN) LED Input
Black  Ground (RTN)
Red +VDC
Drain Unused
Brown  Red LED Input
Blue  Hold Input          
Connect the reader to the host according to the 
wiring table below and the host installation guide.
Pigtail Discription
Red/Grn GPIO1 (RS232-T/RS485-A)
Tan  GPIO2 (RS232-R/RS485-B)
Violet  Open Collector Output
White  Wiegand Data 1 / Clock
Green  Wiegand Data 0 / Data
Pink  GPIO3 (RS485-Z)
Gray  GPIO4 (RS485-Y)