Aiphone IX1AS10AS Instructions User Manual

IX SERIES
IX-1AS / IX-10AS 2-Wire Network Adaptor
Installation & Programming Guide
This is an installation and programming manual addressing wiring and programming for the IX-1AS / IX-10AS 
adaptor. For general IX Series programming, a complete set of instructions 
(IX Web Setting Manual / IX Operation 
Manual / IX Support Tool Setting Manual) 
can be found on the DVD-ROM provided with the IX-MV Master Station. 
ATTENTION:
IX SystemIP network-compatible intercomVideo Door Station (IX-DA)
Audio Only Door...

2 | IX-1AS Installation & Programming Guide
Step 1: Logging into the IX-1AS adaptor
The IX-1AS / IX-10AS adaptor is designed for use with Aiphone’s 2 wire LE and NE Series sub stations. This adaptor will allow 
these subs to be used with the IX-MV network master station. First, connect the door station to the adaptor as shown in the 
table below, then connect the adaptor to the network. The door station will announce its IP address once the network connection 
is made....

3 
Step 3: Network Settings
Step 4: Contact Output Settings (optional)
Select Network Settings from the menu on the left. Enter a unique IP Address*, Subnet Mask, and Gateway IP Address for 
the adaptor. Consult with your IT department for the appropriate addresses to be assigned.
There are additional settings on the Network Settings page that can be adjusted: SIP Settings, Audio Settings, and Packet 
Priority. The default settings will work in most cases. Adjust as necessary.
Click the 
 button to...

4 | IX-1AS Installation & Programming Guide
Step 5: Call Settings
Select Call Settings from the menu on the left. From this screen, enter the station number and IP address of the master(s) 
that this door station needs to call. A maximum of 20 master stations can be entered (example: [email protected]). These 
station numbers and IP Addresses must match what is assigned to the IX-MV master(s) in IX Support Tool.
The adaptor will work with the following settings left at default. Adjust as neccessary.
From...

5 
Step 6: Function Settings (continued)
SIF Reporting and SIF Events can be enabled from the same Function Settings screen. This is used when integrating with 
access control platforms (i.e. RY-IP44). Enter the IP address (of 3rd party device), Port (of 3rd party device), and Program number 
for each destination under SIF Reporting. Under SIF Events, use the appropriate radio buttons to enable events to be sent to the 
destination addresses. When enabling Periodical Transmission, select the transmission...

6 | IX-1AS Installation & Programming Guide
Step 8: Maintenance (optional)
Select Maintenance from the menu on the left. If a Syslog server is being used on the network, the IP address for the server can 
be entered here. If Syslog Address is left to the 0.0.0.0 address, the log will be broadcast. Enable debug mode for additional syslog 
messages to aid in troubleshooting.
HQ
Step 9: Adding the IX-1AS to the IX-MV

added sub station. 
Open IX Support Tool and select the system to be updated.
Select...

7 
Select Address Book from the System Information tree on the left. Each master station in the system will be listed on the 
left and all devices in the system will be listed across the top. By default, the newly added station will be listed in each master 
stations address book. If a station is not to appear in a master stations address book, uncheck the appropriate box.
Click the 
 button to save the changes.
Step 11: Removing the IX-1AS from the IX-MV Address Book (optional)
Step 12: Door Release...

8 | IX-1AS Installation & Programming Guide
6SHFL¿FDWLRQV
Power:      Power-over-Ethernet (IEEE 802.3af, class 0)
Current Consumption:       Maximum 250mA per IX-1AS
Door Release Relay:    24V DC, 500mA
Camera Call Up Relay:    24V DC, 500mA
Communication:        Hands-free Half duplex, VOX
LAN:      Ethernet (10BASE-T, 100BASE-TX)
Audio Codec:     G.711
Protocol:          IPv4, TCP, UDP, SIP, HTTP, RTP, RTCP, IGMP, DHCP
Operating Temperature:      32°F ~ 122°F (0°C ~ 50°C)
Material:      Aluminum...