Aiphone ISSSRAR Instructions User Manual

							IS-SS-RA-R
Stainless Steel Flush Mount Door Station with an Emergency Call Button
-INSTRUCTIONS-
Pg.1
The IS-SS-RA-R is a stainless steel flush mount door station with an emergency call button.  The 
unit is equipped with ADA compliant lettering and Braille signage for the emergency button. A call 
status indicator is included to meet ADA rescue assistance requirements. The IS-SS-RA-R must be 
programmed as an audio door station and can connect to any control unit in the IS system (IS-CCU, 
IS-SCU, or IS-RCU).
1
2
3
4
5
6
IS-SS-RA-R NAMES & FUNCTIONS:
 
1. Microphone   4. Call status indicator
2. Speaker      5. Signage with Braille
3. Name Placard    6. Emergency button
 
FEATURES: 
•  Audio communication with calling area
•  Emergency call button
•  ADA compliant lettering and Braille signage
•  LED call status indicator
•  Two programmable relay outputs for 
activation of external systems/devices
•  Name placard
•  Stainless steel faceplate with tamper 
resistant screws
PACKAGE CONTENTS:
IS-SS-RA-R
Vandal-resistant Door Station
Semi-flush backbox & 
tamper-resistant screws Security Driver
Blank name placard
INSTALLATION: 
•  For flush mounting, cut a hole in the wall and 
use supplied back box.  
Box dimensions are:  
11-1/16” H x 5-7/8” W x 1-3/4” D 
•  For surface mounting, use the SBX-ISDVFRA 
surface mount box. This box can mount to a 
standard 1-gang box or to any flat surface.
STEADY GREE N INDICATES CALL  ANSWERED
EMERGENCY
2-pin connector
for external reset 
						

							Pg. 2
IS-SS-RA-R Instr.
0413JD
Aiphone Corporation
1700 130th AVE NE * Bellevue, WA 98005
Ph: (800) 692-0200 * Fax: (425) 455-0071
[email protected]
WIRING DIAGRAM:
IS-SS-RA-R
IS-CCU
IS-MV
IS-PU-UL
N/O Dry Contact 
24V AC/DC 500mA
CAT-5e
CAT-5e
NO
COM
NC
FCC WARNING:This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1)  This device may not cause harmful interference.
(2)  This device must accept any interference that may cause undesired operation.
•  For proper regulatory compliance, the drain wire should be disconnected at the power 
supply end of the cable.
•  Changes or modifications not expressly approved by the party responsible for 
compliance could void the user’s authority to operate the equipment.
TOLL FREE TECHNICAL SUPPORT:
(800) 692-0200
E-MAIL: [email protected]
SPECIFICATIONS:
Terminations:    RJ45 jack for audio
      Screw terminals for door release and relay outputs
Relay rating:    24V AC/DC 500mA on Door station, 24V AC/DC 1.0A on relay board
Operating Temp:  14° ~ 140°F / -10° ~ 60°C
Wiring Distance:  980’ with Cat-5e/6 cable
Dimensions:    11-3/4” H x 7” W
w/SBX-ISDVFRA:  11-11/16” H x 7-1/16” W x 2-13/16” D (top), 1-13/16” D (bottom)
OFFONNO
NOCNCCNC
1234
OFFON
NO
NOC
NC
C
NC1234
Board on back of unit See wiring below
RELAY BOARD WIRING AND SETTINGS:
Relay 1 Output
N/O, COM, N/C
Relay 2 Output
N/O, COM, N/C
**Relay 2 External Reset
Connect to N/O dry switch
Configuration Switch  See Settings to rightON
1 234
Default Configuration when shipped
Optional Configuration
Normal Call
Emergency Call
Talking
Door Release Trigger Source RY1 Triggered? RY1 Remains ON 
During Talking?
RY2 Triggered?RY2 Remains ON 
During Talking? RY2 Requires 
Reset?YES
NO N/A
YES
YES
YESYES
YES NO
NO
NO
NO N/A
N/A
N/AN/A
N/A
N/A
YES YES
ON
1
234
Contact Technical Support if additional switch configurations 
are required.  
Relay 1 triggers on normal call, emergency call, and communication. Relay 1 remains on during communication.  
Relay 2 triggers on emergency call and remains on during communication.
Relay 1 triggers on normal call, emergency call, and communication. Relay 1 remains on during communication.  
Relay 2 triggers on an emergency call and remains on during communication.  Relay 2 requires reset.
Normal Call
Emergency Call
Talking
Door Release Trigger Source RY1 Triggered? RY1 Remains ON 
During Talking?
RY2 Triggered?RY2 Remains ON 
During Talking? RY2 Requires 
Reset?YES
NO N/A
YES
NO
N/A
N/A N/A
YES YES
YES
YES
YES
YESN/A
N/A
N/A
NO
NO YES**
* IS-SS-RA-R can connect to any 
control unit (IS-CCU, IS-SCU, IS-RCU)
Station must be programmed as an 
audio only station.
*
2-pin connector