Aiphone ISSSCI Instructions User Manual

							IS-SS-CI
Stainless Steel Flush Mount Door Station with Camera Input
-INSTRUCTIONS-
Pg.1
The IS-SS-CI is a stainless steel flush mount door station with a camera input.  A call status indicator 
is included to meet ADA rescue assistance requirements. The IS-SS-CI must be programmed as a 
video door station and must connect to the IS-CCU or IS-SCU control units.
1
2
3
4
5
IS-SS-CI NAMES & FUNCTIONS:
 
1. Microphone   4. Call status indicator
2. Speaker      5. Call button    
3. Name Placard   
 
FEATURES: 
•  Audio communication with calling area
•  LED call status indicator
•  CCTV input (Analog NTSC 1Vpp)
•  Two programmable relay outputs for 
activation of external systems/devices
•  Name placard
•  Stainless steel faceplate with tamper 
resistant screws
PACKAGE CONTENTS:
IS-SS-CI
Vandal-resistant Door Station
Semi-flush backbox & 
tamper-resistant screws Security Driver
Blank name placard
INSTALLATION: 
•  For flush mounting, cut a hole in the wall and 
use supplied back box.  
Box dimensions are:  
11-1/16” H x 5-7/8” W x 1-3/4” D 
•  For surface mounting, use the SBX-ISDVFRA 
surface mount box. This box can mount to a 
standard 1-gang box or to any flat surface.
STEA DY GREEN INDICATES CALL  ANSW ERED4-pin connector
for CCTV 
						

							Pg. 2
IS-SS-CI Instr.
0413JD
Aiphone Corporation
1700 130th AVE NE * Bellevue, WA 98005
Ph: (800) 692-0200 * Fax: (425) 455-0071
[email protected]
WIRING DIAGRAM:
IS-SS-CI
IS-CCU
IS-MV
IS-PU-ULCAT-5e
CAT-5e
FCC WARNING:This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1)  This device may not cause harmful interference.
(2)  This device must accept any interference that may cause undesired operation.
•  For proper regulatory compliance, the drain wire should be disconnected at the power 
supply end of the cable.
•  Changes or modifications not expressly approved by the party responsible for 
compliance could void the user’s authority to operate the equipment.
TOLL FREE TECHNICAL SUPPORT:
(800) 692-0200
E-MAIL: [email protected]
SPECIFICATIONS:
Terminations:    RJ45 jack for audio/video
      Screw terminals for door release and relay outputs
Relay rating:    24V AC/DC 0.5A on Door station, 24V AC/DC 1.0A on relay board
Camera Input:   Analog NTSC 1Vpp
Operating Temp:  14° ~ 140°F / -10° ~ 60°C
Wiring Distance:  980’ with Cat5e/6 cable
Dimensions:    11-3/4” H x 7” W
w/SBX-ISDVFRA:  11-11/16” H x 7-1/16” W x 2-13/16” D (top), 1-13/16” D (bottom)
OFFONNO
NOCNCCNC
1234
OFFON
NO
NOC
NC
C
NC1234
Board on back of unit See wiring below
RELAY BOARD WIRING AND SETTINGS:
CCTV Input
CCTV Output
Relay 1 Output
N/O, COM, N/C
Relay 2 Output
N/O, COM, N/C
For door release
1.0 Amp contact *75Ω termination 
for CCTV output
* Unit is shipped with the pin connector set to the ON 
position. Change pin connector to the OFF position to 
loop video from the CCTV output.
Configuration Switch See Settings to rightON
1 234
Default Configuration when shipped
Optional Configurations
ON
1234Normal Call
Emergency Call
Talking
Door Release Trigger Source RY1 Triggered? RY1 Remains ON 
During Talking?
RY2 Triggered?RY2 Remains ON 
During Talking? RY2 Requires 
Reset?YES
NO N/A
YES
NO
N/A
N/A NO N/A
YES YES
YES
YES
YES YESN/A
N/A
N/A
NO
NO
Contact Technical Support if additional switch configurations 
are required.  
Normal Call
Emergency Call
Talking
Door Release Trigger Source RY1 Triggered? RY1 Remains ON 
During Talking?
RY2 Triggered?RY2 Remains ON 
During Talking? RY2 Requires 
Reset?YES
NO N/A
YES
YES
YES
YES**NO
NO
NO NO NO
N/AN/A
N/A
N/A
YES YES
NONO
**Connected to door release output 
of door station  when shippedRelay 1 triggers on normal call, emergency call, and communication. Relay 1 remains on during communication.  
Relay 2 triggers when the door release button of the master is pressed.  Use this configuration if you need a larger 
relay contact than the 0.5 Amp supplied from the door station.
Relay 1 triggers on normal call, emergency call, and communication.  Relay 1 remains on during communication.
Relay 2 triggers on communication and remains on during communication.
*
* Connect to the IS-CCU or IS-SCU and 
program as a video door station, even if no 
CCTV camera is connected. 
ON
1 234Normal Call
Emergency Call
Talking
Door Release Trigger Source RY1 Triggered? RY1 Remains ON 
During Talking?
RY2 Triggered?RY2 Remains ON 
During Talking? RY2 Requires 
Reset?YES
NO N/A
YES
NO
N/A
N/A NO
N/A
YES YES
YES
YES
YES
YESN/A
N/A
N/A
NO
NO
***Option Input
Any N/O dry contact  can be used. *** Relay 1 triggers on normal call and communication.  Relay 1 remains on during communication. Relay 2 triggers 
when option input is triggered and remains on during communication.
If using this configuration Relay 2 can not be used for door release.  
You must wire directly from the door station 
relay output for door release and disconnect the Red/Bown wires that are currently wired to the door station relay .
4-pin connector