Aiphone ISIPDVFRP10 Instructions User Manual

							Pg. 1
IS-IPDVF-RP10
Vandal Resistant IP Color Video Door Station
with Built in HID multiCLASS SE® Card Reader
The IS-IPDVF-RP10 is an IS Series IP color video door station with a multiCLASS SE® Card Reader 
built onto the same stainless steel faceplate. The card reader provides electronic access to a building 
through a separate Access Control System, which is not supplied by Aiphone.  
The IS-IPDVF-RP10 will connect directly to a network switch.
-INSTRUCTIONS-
NAMES & FUNCTIONS: 
1.  Camera      5.  Name Placard
2.  Microphone    6.  Call status indicator
3.  LED Light     7.  Call button
4.  Speaker      8.  multiCLASS SE
®
         
Reader
FEATURES: 
•  All-in-one solution: Communication product & 
card reader
•  If a card is missing or malfunctioning,   
audio/video communication can provide user 
verification
•  Standard Wiegand output to access panel
•  Convenience of installing combined components
IS-IPDVF-RP10
1
2
3
4
5
6
7
8
STEA
DY GREE N IN DICA TES CALL ANSW ERED
PACKAGE CONTENTS:
IS-IPDVF-RP10
Vandal-resistant Door Station Security Driver
Flush backbox & 
tamper-resistant screws
Blank name 
placard
INSTALLATION: 
•  For flush mounting, cut a hole in the wall and use the 
supplied back box.  
Box dimensions are: 11-3/4” H x 5-13/16” W x 1-3/4” D
•  For surface mounting, use the SBX-ISDVFP surface 
mount box. 
This box can mount to a standard 1 gang box or to any 
flat surface. 
						

							Pg. 2
IS-IPDVF-RP10 Instr.
0615JD
WIRING DIAGRAM:
IS-IPDVF-RP10IS-IPMV
Pigtail Discription
Yellow 
Beeper Input
Orange  Green (GRN) LED Input
Black  Ground (RTN)
Red +VDC
Drain Unused
Brown  Red LED Input
Blue  Hold Input          
Connect the reader to the host according to the 
wiring table below and the host installation guide.
TESTING & OPERATION:
• When power is applied to the multiCLASS SE® reader, the LED will turn RED while the beeper 
beeps simultaneously 3 times (the last tone is a higher frequency).  The LED will then flash once 
after the last tone. This indicates that the microcontroller is operating properly. 
•  Present an ID card to the reader (hold card directly in front of reader\
). The LED will momentarily 
turn green while the beeper beeps once, indicating that the card was rea\
d successfully.
SPECIFICATIONS:
CARD READER:
Reader model:  RP10
Power Source:  5 ~ 16V DC
Current:    75mA (Avg); 200mA (peak)
Transmit Freq.   13.56 MHz & 125 kHz
Terminations:    Color-coded pre-wired pigtail
Wiring Distance:  500’
Operating Temp:  -31° ~ 150°F / -35° ~ 65°C
Operating Humidity:  5-95% relative humidity
   non-condensing CAMERA:
Camera unit:   
CMOS camera
Scanning line:   525 lines
Min. illumination:  5 Lux at 1’6”
Terminations:    RJ45 jack for audio/video
      Screw terminals for door release
Operating Temp:  14° ~ 140°F / -10° ~ 60°C
Wiring Distance:  328’ with Cat5e/6 cable
Dimensions:    12-3/8” H x 7” W
w/SBX-ISDVFP:  12-13/16” H x 7-1/16” W x 2-13/16” D   
      (top), 1-13/16” D (bottom)
FCC WARNING:This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1)  This device may not cause harmful interference.
(2)  This device must accept any interference that may cause undesired operat\
ion.
• For proper regulatory compliance, the drain wire should be disconnected \
at the power 
supply end of the cable.
•  Changes or modifications not expressly approved by the party responsible for 
compliance could void the user’s authority to operate the equipment.
•  The Reader is intended to be powered from a limited power source output \
of a 
previously certifed power supply
NO
COM
NC
To Strike
& Power
CAT-5e
CAT-5e
Pigtail Discription
Red/Grn  GPIO1 (RS232-T/RS485-A)
Tan  GPIO2 (RS232-R/RS485-B)
Violet  Open Collector Output
White  Wiegand Data 1 / Clock
Green  Wiegand Data 0 / Data
Pink  GPIO3 (RS485-Z)
Gray  GPIO4 (RS485-Y)
Aiphone Corporation
P: 800.692.0200
[email protected]/home