Aiphone ISIPDVFHID Instructions User Manual

							Pg. 1
IS-IPDVF-HID
Vandal Resistant IP Color Video Door Stationwith Built in Proximity Card Reader
The IS-IPDVF-HID is an IS Series IP color video door station and an HID ProxPoint Plus Card 
Reader, built onto the same stainless steel faceplate. The card reader provides electronic access to a 
building through a separate Access Control System, which is not supplied by Aiphone.  
The IS-IPDVF-HID will connect directly to a network switch.
-INSTRUCTIONS-
NAMES & FUNCTIONS: 
1.  Camera      5.  Name Placard
2.  Microphone    6.  Call status indicator
3.  LED Light     7.  Call button
4.  Speaker      8.  Prox Reader
FEATURES: 
•	 All-in-one solution: Communication product & 
card reader
•	 If a card is missing or malfunctioning,   
audio/video communication can provide user 
verification
•	 Standard Wiegand output to access panel
•	 Convenience of installing combined components
IS-IPDVF-HID
1
2
3
4
5
6
7
8
PACKAGE CONTENTS:
IS-IPDVF-HID
Vandal-resistant Door Station Security Driver
Flush backbox & 
tamper-resistant screws
Blank name 
placard
INSTALLATION: 
•	 For	flush	mounting,	cut	a	hole	in	the	wall	and	use	the	
supplied back box.  
Box dimensions are: 11-3/4” H x 5-13/16” W x 1-3/4” D
•	 For surface mounting, use the SBX-ISDVFP surface 
mount box. 
This box can mount to a standard 1 gang box or to 
any	flat	surface. 
						

							Pg. 2
IS-IPDVF-HID Instr.
0113JD
Aiphone Corporation
1700 130th AVE NE
Bellevue, WA 98005
(425) 455-0510 
Fax: (425) 455-0071
WIRING DIAGRAM:
IS-IPDVF-HID IS-IPMV
Wiegand Wire   
Color
+ DC (5-16V)    Red
Ground   Black
Data0   Green
Data1   White
Shield Ground    Drain
Green LED    Orange
Red LED   Brown
Beeper   Yellow
Hold   Blue
Card Present    Violet
Connect the reader to the host according to the 
wiring table below and the host installation guide.
TESTING & OPERATION:
•	When	power	is	applied	to	the	card	reader,	the	LED	will	flash	green	three	(3)	times	while	the	
beeper beeps simultaneously.  The LED will then turn red.  This indicates that the microcontroller 
is operating properly. 
•	 Present an ID card to the reader (hold card directly in front of reader\
).  The LED will momentarily 
turn green while the beeper beeps once, indicating that the card was rea\
d successfully.
SPECIFICATIONS:
CARD READER:
Reader type:    6005B ProxPoint Plus
Power Source:  5 ~ 16V DC
Max Voltage:    18V DC
Current:    30mA (Avg); 75mA (peak)
Terminations:    Color-coded pre-wired pigtail
Wiring Distance:  500’
Operating Temp:  14° ~ 140°F / -10° ~ 60°C
Operating Humidity:  0-95% relative humidity
   non-condensing CAMERA:
Camera unit:   
CMOS camera
Scanning line:   525 lines
Min. illumination:  5 Lux at 1’6”
Terminations:    RJ45 jack for audio/video
      Screw terminals for door release
Operating Temp:  14° ~ 140°F / -10° ~ 60°C
Wiring Distance:  328’ with Cat5e/6 cable to switch
Dimensions:    12-3/8” H x 7” W
w/SBX-ISDVFP:  12-7/16” H x 7-1/16” W x 2-13/16” D   
       (top), 1-13/16” D (bottom)
FCC WARNING:This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1)  This device may not cause harmful interference.
(2)  This device must accept any interference that may cause undesired operat\
ion.
•	For proper regulatory compliance, the drain wire should be disconnected \
at the power 
supply end of the cable.
•	 Changes	or	modifications	not	expressly	approved	by	the	party	responsible	for	
compliance could void the user’s authority to operate the equipment.
•	 The Reader is intended to be powered from a limited power source output \
of a 
previously certifed power supply
TOLL FREE TECHNICAL SUPPORT:
(800) 692-0200
E-MAIL: [email protected]
NO
COM
NC
To Strike & Power
CAT-5e
CAT-5e
Note: Please refer to the IS Series literature for 
complete installation and programming instructions.