Aiphone ISIP4DVF Instructions User Manual

							Pg. 1
IS-IP4DVF
IP Video Door Station with 4 Call Buttons
The IS-IP4DVF is an IS Series IP video door station with 4 call buttons for selective calling to  
IS-IPMV master stations. The RY-IP44 adaptor is required for assigning the call buttons to specific 
master stations within the IS-IP configuration (refer to the RY-IP44 programming manual for 
programming instructions). The IS-IP4DVF will connect to a network switch, and the call buttons wil\
l 
connect to the RY-IP44 adaptor inputs.
-INSTRUCTIONS-
NAMES & FUNCTIONS: 
1.  Camera      5.  Directory card
2.  Microphone    6.  Call status indicator
3.  LED illuminator    7.  Call buttons with integrated
4.  Speaker
           name placard  
FEATURES: 
•  IP video door station
•  4 call buttons for selective calling to master stations   
(RY-IP44 adaptor required)
•  LED call status indicator
•  5 name placards
•  Stainless steel faceplate with tamper resistant screws
IS-IP4DVF
1
2
3
4
5
6
7
PACKAGE CONTENTS:
IS-IP4DVF
4 Call Button  Door Station Security Driver
Flush backbox & 
tamper resistant screws Blank name 
placard x5
INSTALLATION: 
•  For flush mounting, cut a hole in the wall and use the 
supplied back box.  
Box dimensions are: 11-3/4” H x 5-13/16” W x 1-3/4” D
•  For surface mounting, use the SBX-ISDVFP surface 
mount box. This box can mount to a standard 1 gang 
box or to any flat surface.
SA-1 x 3
Note: 
When installing the IS-IP4DVF in the supplied back box, the call 
button assembly may come loose. Push call button assembly 
back in to position as necessary. 
						

							Pg. 2
IS-IP4DVF Instr.
1015
Aiphone Corporation
www.aiphone.com
[email protected]
P: 800.692.0200
WIRING DIAGRAM:
IS-IP4DVF
Back View IS-IPMV
PROGRAMMING:
The IS-IP4DVF door station must be set as a host or client device like a\
ny other IS-IP door station or master 
station. The unit must be registered to the IS-IP system before it can be programmed to call a master station 
using the call buttons and RY-IP44 adaptor. Refer to Steps 5-7 in the IS Series IP Direct System Programming 
Guide for information on setting client and host devices and registering\
 IP stations.
SPECIFICATIONS:
Camera unit:   
CMOS camera
Scanning line:   525 lines
Min. illumination:  5 Lux at 1’6”
Terminations:    RJ45 jack for audio/video
      Screw terminals for door release and call buttons
Operating Temp:  14° ~ 140°F / -10° ~ 60°C
Wiring Distance:  328’ with CAT-5e/6 cable to switch
Dimensions:    12-3/8” H x 7” W
w/SBX-ISDVFP:  12-7/16” H x 7-1/16” W x 2-13/16” D   (top), 1-13/16” D (bottom)
FCC WARNING:This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1)  This device may not cause harmful interference.
(2)  This device must accept any interference that may cause undesired operation.
• For proper regulatory compliance, the drain wire should be disconnected \
at the power 
supply end of the cable.
•  Changes or modifications not expressly approved by the party responsible for 
compliance could void the user’s authority to operate the equipment.
NO
COM
NC
To Strike
& Power
CAT-5e
CAT-5e
Note: Refer to the RY-IP44 
Programming Manual for 
information on programming 
the adaptor.
IS-IPMVIS-IPMV
IS-IPMVCAT-5e CAT-5e
CAT-5e
CAT-5e
I1I2
GG
I3I4
RY-IP44
-+Power
~~~~~~SA-1 SA-1SA-1
SA-1 modules are included to protect the 
RY-IP44 adaptor from surge. Locate the 
SA-1 modules near the RY-IP44 adaptor 
and connect the ground terminal on each 
SA-1 to an earth ground.