Aiphone ISDVFHID Instructions User Manual

							Pg. 1
IS-DVF-HID
Vandal Resistant Color Video Door Station
with Built in Proximity Card Reader
The IS-DVF-HID is an IS-series color video door station and an HID ProxP\
oint Plus Card Reader, 
built onto the same stainless steel faceplate.  The card reader provides electronic access to a 
building through a separate Access Control System, which is not supplied by Aiphone.  
The IS-DVF-HID can connect to the IS-CCU or IS-SCU control units.
-INSTRUCTIONS-
NAMES & FUNCTIONS: 
1.  Camera     5.  Name Placard
2.  Microphone   6.  Call status indicator
3.  LED Light    7.  Call button
4.  Speaker     8.  Prox Reader
FEATURES: 
•	All-in-one solution: Communication product & 
card reader
•	If a card is missing or malfunctioning,  
audio/video communication can provide user 
verification
•	Standard Wiegand output to access panel
•	Convenience of installing combined components
IS-DVF-HID
1
2
3
4
5
6
7
8
STEADY GREE N IN DICA TES CALL AN SWERED
PACKAGE CONTENTS:
IS-DVF-HIDVandal-resistant Door Station
Security Driver
Flush backbox & tamper-resistant screws
Blank name placard
INSTALLATION: 
•	For	flush	mounting,	cut	a	hole	in	the	wall	and	use	the	
supplied back box. 
Box dimensions are: 11-3/4” H x 5-13/16” W x 1-3/4” D
•	For surface mounting, use the SBX-ISDVFP surface 
mount box. 
This box can mount to a standard 1 gang box or to 
any	flat	surface. 
						

							Pg. 2IS-DVF-HID Instr.0311JD
Aiphone Corporation1700 130th AVE NEBellevue, WA 98005(425) 455-0510 Fax: (425) 455-0071
WIRING DIAGRAM:
IS-DVF-HID
IS-CCUIS-MV
Wiegand Wire   Color
+ DC (5-16V)   RedGround     BlackData0     GreenData1     WhiteShield Ground   DrainGreen LED   OrangeRed LED     BrownBeeper     YellowHold     BlueCard Present   Violet
Connect the reader to the host according to the wiring table below and the host installation guide.
IS-PU-UL
TESTING & OPERATION:
•	When	power	is	applied	to	the	card	reader,	the	LED	will	flash	green	three	(3)	times	while	the	
beeper beeps simultaneously.  The LED will then turn red.  This indicates that the microcontroller 
is operating properly. 
•	Present an ID card to the reader (hold card directly in front of reader\
).  The LED will momentarily 
turn green while the beeper beeps once, indicating that the card was rea\
d successfully.
SPECIFICATIONS:
CARD READER:
Reader type:   6005B ProxPoint Plus
Power Source: 5 ~ 16V DC
Max Voltage:   18V DC
Current:   30mA (Avg); 75mA (peak)
Terminations:   Color-coded pre-wired pigtail
Wiring Distance: 500’
Operating Temp: 14° ~ 140°F / -10° ~ 60°C
Operating Humidity: 0-95% relative humidity
     non-condensing
CAMERA:
Camera unit:   CMOS camera
Scanning line:  525 lines
Min. illumination: 5 Lux at 1’6”
Terminations:   RJ45 jack for audio/video
     Screw terminals for door release
Operating Temp: 14° ~ 140°F / -10° ~ 60°C
Wiring Distance: 980’ with Cat5e/6 cable
Dimensions:   12-3/8” H x 7” W
w/SBX-ISDVFP: 12-7/16” H x 7-1/16” W x 2-13/16” D   
      (top), 1-13/16” D (bottom)
FCC WARNING:This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:(1)  This device may not cause harmful interference.(2)  This device must accept any interference that may cause undesired operat\
ion.•	For proper regulatory compliance, the drain wire should be disconnected \
at the power supply end of the cable.•	Changes	or	modifications	not	expressly	approved	by	the	party	responsible	for	compliance could void the user’s authority to operate the equipment.•	The Reader is intended to be powered from a limited power source output \
of a previously certifed power supply
TOLL FREE TECHNICAL SUPPORT:
(800) 692-0200
E-MAIL: [email protected]
NOCOMNC
To Strike
& Power
CAT-5e
CAT-5e