Aiphone IER2 Instructions User Manual

							Model;IER-2, Call extension speaker
INSTALLATION & OPERATION MANUAL
- 1 -
FK1829 0709
1  SYSTEM OUTLINE & COMPONENTS Precautions on Installation
CAUTION 
2  NAMES & FEATURES
A
CALL EXTENSION
PACKAGE CONTENTS
. 
Call extension Speaker (IER-2)
. 
Packet of screws
. 
Installation & Operation 
  Manual
FEATURES. 
Announces a call tone.  No communication. 
. 
One speaker for the master (or sub) station.
. 
Volume adjustment to 3 positions.
. 
Surface-wall single-gang mounting. The IER-2 is a call extension speaker for hearing a chime 
tone in a location remote from the master or sub station. 
The chime is the same from the IER-2 as is emitted from 
the intercom, and it is equipped with a 3-position volume 
switch. There is no reply from the IER-2. In order that the product can be used safely and properly, please observe the following Precautions.
(
Negligence could result in injury or damage to property.) 
Mount IER-2 in a convenient location, but not where it could be bumped or jarred.
Do not install or make any wire terminations while power supply is plugged in. It can cause electrical
shock or damage to the unit.
Do not install IER-2 in any of the following locations, as it may cause the system to malfunction;
. 
High or extreme cold temperature area: 
  under direct sunlight, near equipment that varies in temperature, in front of air conditioner, inside a refrigerated area,    
  etc.
. 
Places subject to moisture or humidity extremes (bathroom, cellar, greenhouse, etc.)
. 
Places subject to environmental conditions, such as oil, dust, chemicals, salt, etc.
. 
Places subject to steam or smoke (near heating equipment or cooking surfaces)
IER-2
Speaker
Screw hole (x2)Call tone volume 
control
IER-2
2IER-2
Intercom master or sub stationChime
or audio 
tone 
						

							3  MOUNTING5  OPERATIONS
4  WIRING
AIPHONE CO., LTD., NAGOYA, JAPAN
AIPHONE CORPORATION, BELLEVUE, WA, USA
AIPHONE S.A.S., LISSES-EVRY, FRANCE
- 2 -
WARRANTYAiphone warrants its products to be free from defects of material and workmanship under normal use and service for a period 
of one year after delivery to the ultimate user and will repair free of charge or replace at no charge, should it become defective 
upon which examination shall disclose to be defective and under warranty. Aiphone reserves unto itself the sole right to make 
the final decision whether there is a defect in materials and/or workmanship; and whether or not the product is within the 
warranty. This warranty shall not apply to any Aiphone product which has been subject to misuse, neglect, accident, power 
surge, or to use in violation of instructions furnished, nor extended to units which have been repaired or altered outside of the 
factory. This warranty does not cover batteries or damage caused by batteries used in connection with the product. This 
warranty covers bench repairs only, and any repairs must be made at the shop or place designated in writing by Aiphone. 
Aiphone will not be responsible for any costs incurred involving on site service calls. Aiphone will not provide compensation for 
any loss or damage incurred by the breakdown or malfunction of its products during use, or for any  consequent inconvenience 
or losses that may result.
Printed in Vietnam(E)IER-2-I(E) 0709A
1. Connect a pair of wires to screw terminals on back.
2. Attach IER-2 unit to wall or single-gang box with 
supplied screws.
3. For surface-wall mounting, run the cable either from 
top or bottom of the unit.
Clean IER-2 unit with a soft cloth dampened with 
neutral household cleanser.  Never use any abrasive 
cleaner or cloth.
. 
Unit housing: Plastic
. 
Wiring: 2 wires, non-polarized to an inside station
              (master or sub).
. 
Dimensions:120H x 88W x 29D (mm).  
                      4-3/4H x 3-1/2W x 1-1/8D.
. 
Weight: 150g (0.33 lbs.).Adjusting call tone volume
Cleaning
IER-2 is not a weather-resistant type.  Do not install 
outdoors. Mounting location
6  TECHNICAL PRECAUTIONS
When call tone sounds, there is no communication.
To reply, come to the inside station.
6  TECHNICAL PRECAUTIONS
7  SPECIFICATIONS (IER-2)
Remove
Back view
(top, right)
. 
Make a cable inlet hole in the top.
http://www.aiphone.net/ Sinlge-gang box
IER-2
Screw (x2)
83.5mm
(3-5/16)
. Single-gang wall mounting. 
Surface-wall mounting
Wall
IER-2
Wood
screw (x2)
x
x
IER-2
Connecting terminals may vary by intercom station.
Refer to the Manual packed with the intercom station. Intercom 
master or 
sub station
1
E
Non-polarized
HIGH
MEDIUM
LOW
AIPHONE
IER-2
Connecting
cableConnecting
cable