Aiphone HIDSS Instructions User Manual

							- INSTRUCTIONS -
The HID-SS is a 2-gang stainless steel unit that contains an HID ProxPoint® Plus Card Reader. This module installs 
next to any one of Aiphone’s 2-gang stainless steel sub stations (-SS and -SSR series*), creating a unified look with the 
intercom and card reader installed together. Horizontal and vertical surface mount boxes are available for mounting both 
units.  The HID-SS does not need to be used with an intercom station.  The card reader provides electronic access to a 
building through the standard Access Control system, which is not supplied by Aiphone.
HID Proximity Reader Module for 2-Gang Entrance Panel
Page 1
INSTALLATION:
1. Install HID-SS alongside of or below the 2-gang intercom sub station.
2. The HID-SS will mount into the SBX-2BH, SBX-2BV, SBX-2G, or any standard 2-gang box or ring.
3. Secure wire connections as shown on wiring chart.
4. Cut any unused wire so that bare wires are not exposed.
5. Refer to standard product installation manuals for complete system information. No additional information 
pertaining to the Access Control system is provided by Aiphone.
HID-SS
(front view)
Connecting the Reader to the Host:
Connect the reader to the host according to the
wiring table below and the host installation guide.
Wiegand Wire Color
+ DC Red
Ground Black
--- Violet
Data0 Green
Data1 White
Shield Ground Drain
Green LED Orange
Red LED Brown
Beeper Yellow
Hold Blue
HID-SS
(back view)
To Host18 pigtail cable
LED indicator
* See matching models numbers on page 2, 
or see Aiphone Catalog for more information. 
						

							Aiphone Communication Systems
1700 130th Ave. N.E.
Bellevue, WA  98005
(425) 455-0510
FAX (425) 455-0071
HID-SS Instr.
0913JD
SPECIFICATIONS:
Reader: 6005B Series
Power Source: 5.0 – 16.0 VDC
Absolute Max. Voltage: 18 VDC
Peak Current: 80 mA
Avg. Current 5V or 12V: 20 mA
Terminations: Color-coded pre-wired pigtails
Wiring Distance: 500
Dimensions (H x W x D):  4 ¾” x 4 3/4 x 7/8
Operating Temperature: -10° ~ 60° C  /  14° ~ 140° FWhen power is applied to the card reader, the LED will flash green three (3) times    while 
the beeper beeps simultaneously.  The LED will then turn red.  This indicates that the 
microcontroller is operating properly.
Present an ID card to the reader. (Hold card directly in front of reader.) The LED will 
momentarily turn green while the beeper beeps once, indicating that the card was read 
successfully.
TYPICAL LAYOUTS:
2-gang sub and HID-SS
Mounted vertically  in 
SBX-2BV vertical 
surface mount box
2-gang sub and HID-SS 
mounted in SBX-2BH 
horizontal surface mount box
TESTING AND OPERATION:
FCC WARNING:
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference that may cause undesired operation. 
For proper regulatory compliance, the drain wire should be disconnected at the 
power supply end of the cable. 
Changes or modifications not expressly approved by the party responsible for 
compliance could void the user’s authority to operate the equipment. 
The Reader is intended to be powered from a limited power source output of a 
previously certified power supply.
INTERCOM SYSTEM:  MATCHING 
SUB STATIONS:
LEM, LEF, LAF-C/CA, 
AP-M, MP-S series: LE-SS/A, LE-SSR
NEM, NDR, NDRM series: NE-SS/A, NE-SSR
IE, TC-M, TD-H, 
KB Audio door stn: IE-SS/A, IE-SSR
For additional options, please contact Aiphone 
Technical Support. 
HID-SS without 
intercom sub station 
(with optional SBX-2G 
surface mount box)
TOLL FREE TECHNICAL SUPPORT:
(800) 692-0200
E-MAIL: [email protected]