Aimco Brakes Pulse Tool VC1012A Pulse Unit Vacuum Tank System User Manual

							10000 SE Pine St., Portland OR 9\f\b16  • 80085\b1368 • Fax 80058\b9015www.aimcoglobal.com
Vacuum Tank
VC101\b(A)
Operations Manual 
						

							DESCRIPTION AND \fAYOUT
VACUUM TANK L\fD CONTROL PAN\bL
VC1012A MOD\bL ONLY
VACUUM TANK
L\fFT\fNG HANDL\b
SL\fD\b SW\fTCH
VC1012 MOD\bL
ONLY
COMPR\bSS\bD A\fR \fNL\bT
\b 
						

							PROCEDURES
WARNING:
·Read all instructions before operating this equipment.
· Wear proper protective gear.
AIR PRESSURE:
· 7580 PSI
E\fECTRIC:
· 5 AMP 110 VAC
SETTING UP VACUUM TANK:
· Connect 3/8 I.D. air hose to air inlet with full flow 3/8 fittings.
· Plug electric cord into surge protected power strip plugged into 110 VAC outlet.
· Turn power switch on.
USING VACUUM \bI\f\f SYSTEM:
1. Remove lid from tank.
\b. Remove the oil fill plug from the pulse unit and turn torque adjuster all the way out counterclockwise.
Note: Make sure the driving blade is not blocking
the oil fill hole.
3. Set pulse unit or units into the tank and onto the plate. Note: Make sure the plate is in the raised position.
4. Pour Pulstar oil into the tank so that the oil level is about one inch from the top of the liner casing. Note: Make sure to shake the bottle of Pulstar oil vigorously to mix the additive into
the base oil.
5. Put lid back on tank.
OIL FILL PLUG
TORQUE
ADJUSTER
STEP 3STEP 4
3 
						

							PROCEDURES
PROCEDURE \bOR USING VACUUM \bI\f\f TANK SYSTEM
USING VACUUM \bI\f\f SYSTEM:
\f. If you have the VC101\bA push the start button and proceed to step 10.
7. If you have the VC101\b slide the slide switch over so the vacuum starts.
8. After three and a half minutes with the vacuum in the green, lower the plate downinto the oil.
9. Turn the vacuum off. Once normal internal air pressure returns, raise the plate on the inside of the tank.
10. Remove the lid from the tank.
11. Remove the excess oil from the top of the Pulse Unit so that the oil is level with the top of the oil fill hole.
1\b. Draw off the recommended amount of oil from the Pulse Unit and install Oil Fill Plug back into the Pulse Unit.
13. You are now ready to test your tool.
SL\fD\b  SW\fTCH
VC1012 MOD\bL
ONLY
4 
						

							\bI\f \f,  D RAW ,  A ND T O RQ UE T A B\fE
5 
						

							\bI\f\f, DRAW, AND TORQUE TAB\fE
\f 
						

							\bI\f\f, DRAW, AND TORQUE TAB\fE
7 
						

							
AIMCO EUROPE
Avenida Río Gallo, 431
19174 Galápagos - Guadalajara Spain
Phone: + 34 673 34 99 25

LIT-MAN310,   REV.03/16
Printed in USA   ©2016 AIMCO
Corporate Headquarters
10000 S.E. Pine St.
Portland, OR 97216
(800) 852-1368
FAX (800) 582-9015
www.aimco-global.com
 AIMCO Corporation
De Mexico Sa De Cv
Ave. Cristóbal Colon 14529
Chihuahua, Chihuahua. 31125 Mexico
+52-(614) 380-1010
FAX +52 (614) 380-1019
AIMCO China
Room 607, No. 3998 Hongxin Rd Dibao Plaza
Minhang District, Shanghai China
Phone: 0086-21-34319246
Fax: 0086-21-34319245