Home > Aimco Brakes > Nutrunners > Aimco Brakes Nutrunner URW Series Repair Manual

Aimco Brakes Nutrunner URW Series Repair Manual

Here you can view all the pages of manual Aimco Brakes Nutrunner URW Series Repair Manual. The Aimco Brakes manuals for Nutrunners are available online for free. You can easily download all the documents as PDF.

Page 11

- 9   -Disassembly and Reassembly of the Air Motor  
Disassembly  
1. For the  URW - 6 :
a. Remove the Gear Casing from the Handle Casing.
b. Remove the Air Motor from the Handle Casing.    Note :    Applying heat to the  Handle may help in
remov ing the Air Motor.
c. Tap on the splined end of the Rotor with a brass  hammer while holding the Air Motor firmly in your
hand.   Remove the Front Plate, Bearing ,   and Cylinder.
d. Press the Rotor out of the Rear Plate and Bearing.
2. For the  URW - 8N & 9N :...

Page 12

- 10   -Disassembly and Reassembly of the Air Motor  (cont.)
4. Air Motor Plates :    Inspect Plates for grooving.  Light marks can be lapped out using a figure - eight motion
with 220 grit sandpaper on a Lap Plate.  If heavy grooving is noted, replace.
5. Rotor :    Inspect Rotor  for sharp edges in Blade Slots and  pitting and grooving on   Plate  Surface.  Light
marks can be stoned with a mediu m oil stone.  If deep markings exist,  replace.
6. O - Ring :    Inspect the O - rings for splitting or...

Page 13

- 11   -Disassembly and Reassembly of the Air Mo tor  (cont.)
d. Install the Front Plate onto the Rotor aligning the   Roll Pin in the Cylinder and  press the Front Bearing
over the Rotor and int o the Front Plate.   Note :    The  Cylinder should be tight between the Front and
R ear Plate and the Rotor should  tu rn freely
e. Install the O - ring, Rear Plate Spacer ,   and Snap Ring into the Rear Plate.
f. Install the Air Motor into the Handle lining up the   hole in the Handle with the  alignment Pin...

Page 14

- 12   -Disassembly and Reassembly of the Air Motor  (cont.)  
URW  -   Air Motor  
Part 
Number   Description   Part 
Number   Description  
1  
2  
3  
4  
5  
6   Bearing  
Front Plate  
Cylinder  
Roll Pin  
Rear Plate  
Bearing   7  
8  
9  
10  
11   Rear Pla te Spacer (URW - 8 & 9)  
Blade  
Rotor  
O - Ring (URW - 8 & 9)  
Snap Ring (URW - 8 & 9)   

Page 15

- 13   -Recommended Maintenance  
The tools should be thoroughly cleaned and inspected every three months.    Always use genuine  Uryu   parts.  
Lubrication  
Use a light spindle oil for the air   motor like Mobile Spindle Oil No. 1, Shell Spindle Oil 60 ,   and/or equivalent.  
Use a high - quality  g rease for the Gearing, Cam ,   and Racheting sections like S hell Alvania No. 2, Mobilplex 2, 
and/or equivalent.   

Page 16

Corporate Headquarters  
1204 E Maple Road   10000 SE Pine Street   Ave. Morones Prieto 2110 Pte.  
Troy, MI  48083   Portland, OR   97216   Col. Loma Larga  
248 - 583 - 1180 800 - 852 - 1368 Monterrey ,   NL CP   64710, Mexico  
FAX 248 - 583 - 7115 FAX 800 - 582 - 9015 011 - 52 - 81 - 1001 - 1600
www.aimco - global.com FAX 011 - 52 - 81 - 1001 - 1630
LIT - MAN480  
Rev. 
03/2016  Printed in USA  
©2016 AIMCO  
Start reading Aimco Brakes Nutrunner URW Series Repair Manual

Related Manuals for Aimco Brakes Nutrunner URW Series Repair Manual

All Aimco Brakes manuals