Home > Aimco Brakes > Grinders > Aimco Brakes Die Grinder Manual

Aimco Brakes Die Grinder Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Aimco Brakes Die Grinder Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 85 Aimco Brakes manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Operating Instructions for PO Box 16460, Portland, OR 97292-0
    460 • 800-852-1368 •  Fax 800-5 82-9015
    www.aimco-g lobal.com
    Die Grinders  
    						
    							Die Grinders  
    It is  the  responsibility  of  the  employer  to  place  the  information  on  this  
    instruction  sheet  into  the  hands  of  the  operator.  
    AIMCO tools  have  been designed  with safety  in  mind.  
    But  it  is  still  the responsibility  of  the  user  or  service  
    technician  to  insure  that there  is no  misuse.  
    On  the  opposite  page is a  brief  description  of safe  use 
    practices  when  using  grinders.  
    Alwa ys  operate,  inspect ,  and  maintain  this tool  in 
    accordance  with American  National Standards  Institute 
    Safety  Code  for Portable Air  Tools  (ANSI  13186.1)  
    and any  other  applicable  safety  codes  and  regulations.   
    Make sure that these instructions are fully understood 
    before operating  this tool.  The  tool and  its attachments 
    and  accessories  must  only  be  used  for their  designed 
    purpose.  For  product  liability  and  safety  reasons,  any 
    modifications  of  the  tool and  its  accessories  must  be 
    agreed  upon by  the  technical  authority  of  the 
    manufacturer.  All  locally  legislated  safety rules  with  
    regard  to installation,  operation,  and  maintenance  shall 
    be respected at all times. 
    IM PORT ANT  
    						
    							INSTRUCTIONS FOR  SAFE  OPERATION 
    FIRST , follow  your  local  safety  regulations  strictly  on  grinders  and  abrasives.  
    Ensure that the RPM of the grinder does  not  exceed  the 
    rated max.  RPM of  the  insert  
    tool.   
    Remove  the insert  tool  before 
    checking  the RPM  of  the  
    grinder.   
    Make sure that the  rated  speed 
    marking  on the  tool is  readable.   
    Cutting off wheels and routing cutter wheels  shall  not  be  used. 
    Do  not  mis -match  collet sizes and  
    shank  sizes. 
    After mounting the insert tool, operate  the grinder  in  a 
    protected  area to check  that no 
    failure  occurs.  
    Keep the space  around  the 
    grinder  free  from  other  people.  
    Ensure that pressure does not exceed 90  PSI.  Use a  pressure 
    regulator.  Use personal protection equipment.   
    Avoid inhaling  dust resulting from  
    the  grinding  operation  by using  an  
    approved  dust mask  or dust  
    exhaust  system.  
    When  using wire brushes,  wear 
    goggles  and  clothing  that offer 
    protection  from the  thrown wires.  
    Keep loose clothing and long hair clear  of  the  grinder.  
    Beware of run-on. Do not touch the tool, after turning it off, until it 
    has stopped completely.  Turn off air supply before changing insert tool  or  
    disconnecting hose. Beware of 
    whipping air hose. 
    Do not use machine in an explosive  or  potentially  expolsive 
    atmosphere.   
    						
    							AIR HOSE  SIZE:  
    AIR  PRESSUR
    E: 90  PSI  (6.5  kg/cm
    2) Air  Pressure  is recommended  for 
    the  most  efficient  performance.  Too  high  of air pressure  will shorten  the 
    life  of  the  tool.  
    FOR  AIR  MOTOR:  Apply  turbine  oil before  and after  operation.  (For  
    example,  MOBIL  TURBINE  OIL  #32,  SHELL  TURBINE  OIL  #32,  or 
    equivalent.)  
    FOR  BEARINGS:  Apply  recommended  high-quality  grease properly  (for 
    example,  SHELL  ALVANIA  NO.2, SHELL  ALVANIAEP, MOBILPLEX  2, 
    MOBILPLEX  47 or  equivalent)  once  every  three months. Lubrication 
    should be performed by competent personnel during regular overhaul to 
    maintain optimum performance.  
    DRY AND  CLEAN  AIR:  Drain  daily and  install  filter  at or  near the  take-off 
    point  to  prevent  trouble  from foreign  matter. 
    AIR HOSE  AND  JOINTS: Use  air  hose  (the shorter,  the  better), joints,  and 
    other  fittings  of  good  condition  and of  proper size  to avoid  pressure  drop. 
    REGULAR  OVERHAUL:  At  least  once  every  three months, regular  or  
    periodical  overhaul  by  a competent  person  is needed  for best  
    performance  and trouble- free operation.  
    GENUINE  PARTS: Use  only  AIMCO  genuine  spare parts for 
    replacement.   
    Any  repair  of  AIMCO  tools  must be  completed  by AIMCO or  an  authorized 
    AIMCO  Service  Center. Contact  AIMCO  at  (503)  254- 6600  for an 
    authorized Service  Center in  your  area.  
    AIR SUPPLY 
    LUBRICATION 
    MAINTENANCE 
    Air Inlet Air Hose 
    1/8 NPT air inlet use 1/4 ID air hose 1/4 NPT air inlet use 3/8 ID air hose 3/8 NPT air inlet use 1/2 ID air hose 
      
    						
    							AIMCO CORPORATION DE MEXICO SA DE CV 
    Ave. Cristobal Colon 14529  
    Chihuahua, Chihuahua.  31125  
    Mexico 
    Phone: (01 -614) 380- 1010 
    Fax:  (01-614) 380- 1019 
    AIMCO  EUROPE  
    Avenida Río Gallo, 431  
    19174 Galápagos - Guadalajara 
    Spain  Phone: + 34 673 34 99 25  
    AIMCO CORPORATE HEADQUARTERS
     
    10000 SE Pine Street  
    Portland, Oregon  97216  
    Phone: (503) 254– 6600 
    Toll Free: 1 -800- 852-1368  
    AIMCO CHINA  
    Room 607, No. 3998 Hongxin Rd Dibao Plaza  
    Minhang District, Shanghai  
    China  
    Phone: 0086 -21- 34319246  
    Fax: 0086- 21-34319245   LIT-M
    A
    N790      Rev. 03/2016  
    Printed in USA  ©2016 AIMCO 
    						
    All Aimco Brakes manuals Comments (0)

    Related Manuals for Aimco Brakes Die Grinder Manual