Aesthetix Audio PandoraRomulus Advanced Display Functionality User Manual

							
Pandora/Romulus 
Advanced display functionality 
 
 
This unit contains the ability to sense the ambient light level in the room and adjust the display 
and LEDs accordingly.  While the factory settings will work for most situations, there may be 
times when adjustment to the settings is useful.  There are three main sections to the advanced 
display functionality: 
 
Adjustment of display brightness 
Adjustment of LED brightness 
Restoration of the factory default settings 
 
Adjustment of display brightness: 
 
To access this section, first press and hold the  “Standby” button, then concurrently press “up”, or 
the right side of the display.  Then press “up” twice. The display will read SEL 3.  Press the “Mute” 
button once.  This can only be done from the front panel. All LEDs will illuminate and the display 
will show “ 0dd .1.” 
 
The left number indicates the light level that the  sensor is reporting, 0 is darkest and 15 is 
brightest. The 2 characters “dd” indicate that t he parameters showing or to be edited are for the 
display brightness. The rightmost number indicate s the display brightness setting for that light 
level, 0 is darkest and 15 is brightest. The “.”  (dots) on each side of a value indicate that 
parameter has been selected to edit.   Pressing the “up” or “down”  buttons will adjust the display 
brightness for the current  light level.  Pressing the “displ ay” button will move the dots to the 
leftmost parameter, which indica tes that pressing the “up” or “down” buttons will change to a 
different light level setting, for which the display brightness could then be changed by pressing 
the “mute” button.  Changes to the display brightne ss will only be visible for the current light level. 
 
To exit this section, press the “Standby” button once. 
 
 
Adjustment of LED brightness: 
 
To access this section, first press and hold the  “Standby” button, then concurrently press “up”, or 
the right side of the display.  Then press “up” three times. The display will read SEL 4. Press the 
“Mute” button once. This can only be done from the front panel.  All LEDs will illuminate and the 
display will show “0LL .1.” 
 
The left number indicates the light level that the  sensor is reporting, 0 is darkest and 15 is 
brightest. The 2 characters “LL” indicate that t he parameters showing or to be edited are for the 
LED brightness. The rightmost number indicates the  LED brightness setting for that light level, 0 
is darkest and 15 is brightest. The “.” (dots) on ea ch side of a value indicate that parameter has 
been selected to edit.   Pressing the “up” or “dow n” buttons will adjust the LED brightness for the 
current light level.  Pressing the “display” button  will move the dots to the leftmost parameter, 
which indicates that pressing the “up” or “down” buttons will change to a different light level 
setting, for which the LED brightness could then be changed by pressing the “mute” button.  
Changes to the display brightness will only  be visible for the current light level. 
 
To exit this section, press the “Standby” button once. 
 
Note: Setting all brightness levels to the same value, for all light le vels, will result in no change of 
display or LED brightness with changes in ambient light level in the room. 
 
Rev 1.01 2014-04-04 1 
						

							
 
Restoration of the factory default settings: 
 
To restore the factory settings for the LED and display settings, first press and hold the “standby” 
button, then concurrently press “up”.  Then press the “mute” button four times.  The display will 
read SEL 5.  This can only be done from the  front panel.  Press the “mute” button once.  The 
display will read rEuErr and all LEDs will light fo r 3 seconds, indicating that the unit has restored 
the factory settings.  The unit will then revert to the operation mode. 
 
Rev 1.01 2014-04-04 2