AEM Stainless Steel Pressure Sensor 302130XXX User Manual

							  
 
AEM Performance Electronics 
2205 126
th Street Unit A, Hawthorne, CA. 90250 
Phone: (310) 484-2322 Fax: (310) 484-0152 
http://www.aemelectronics.com 
Instruction Part Number: 10-2130 Rev B 
© 2011 AEM Performance Electronics 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
The model 30-2130-XXX family of pressure transducers is specifically designed for pressure measurements in automotive systems. The mechanical 
connection is 1/8 Male NPT.  Each sensor comes with a mating connector plug and pin kit. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Instruction Manual
P/N 30-2130-XXX Pressure Sensors
KIT CONTENTS 
Part Number  Sensor  Connector Kit  -4 Adapter  3/16 Hose Barb 
30-2130-15  15 PSIa (1 Bar)  Included  Included  Included 
30-2130-30  30 PSIa (2 Bar)  Included  Included  Included 
30-2130-50  50 PSIa (3.5 Bar)  Included  Included  Included 
30-2130-75  75 PSIa (5 Bar)  Included  Included  Included 
30-2130-100 100 PSIg  Included Included  NA 
30-2130-150 150 PSIg  Included Included  NA 
30-2130-500 500 PSIg  Included Included  NA 
30-2130-1000 1000 PSIg  Included Included  NA 
30-2130-2000 2000 PSIg  Included Included  NA 
Specifications:  
Accuracy:   +/- 1% FS 
Temp Error:    +/- 1% FS 
Operating Temp:    -40 to 105C 
Burst Pressure:     3 X FS 
Supply Voltage:    5V +/- 0.5V 
Supply Current:    < 6 mA 
Response Time:    < 1 mS 
Vibration:   20G Sinusoidal 
Weight:   < 85 Grams 
Body Material:    304L 
Wetted Material:    316L 
Mechanical Connection:  1/8”NPT Male 
Electrical Connection:  Packard 3-Pin 
 Electrical Termination: 
Signal Ground: Tap to Sensor/Signal Ground on EMS or AQ1 
Sensor Power: Tap to Sensor Power +5V on EMS or AQ1 
Signal: Connect to MAP/Input Channel on EMS or Input 1-8 on AQ1  
						

							IMPORTANT! 
 
The terminals are “Pull to Seat” meaning you must feed the wire through the connector housing BEFORE you crimp on the terminals. The wire is then 
pulled back into the housing and the terminal locks in place. The terminal cannot be inserted or removed from the rear (wire side entry) of the housing.  
See Figure 1. Below 
 
 
 
 
VOLTAGE OUTPUT 
 
Voltage  30-2130-15  30-2130-30  30-2130-50  30-2130-75  30-2130-100 30-2130-150 30-2130-500 30-2130-1000 30-2130-2000 
Range  -14.7-0.3 PSIa  -14.7-15.3 PSIa  -14.7-35.3 PSIa  -14.7-60.3 PSIa  0-100 PSIg  0-150 PSIg  0-500 PSIg  0-1,000 PSIg  0-2,000 PSIg 
0.5 -14.7  -14.7  -14.7 -14.7 0  0  0  0  0 
0.75 -13.763  -12.825  -11.575  -10.013 6.25 9.375 31.25 62.5  125 
1 -12.825  -10.95  -8.45  -5.325 12.5 18.75 62.5  125  250 
1.25 -11.888  -9.075  -5.325  -0.637 18.75 28.125 93.75 187.5  375 
1.5 -10.95  -7.2  -2.2  4.05  25  37.5  125  250  500 
1.75 -10.013  -5.325  0.925  8.738 31.25 46.875 156.25 312.5  625 
2 -9.075  -3.45  4.05  13.425 37.5 56.25 187.5  375  750 
2.25 -8.138  -1.575  7.175  18.113 43.75 65.625 218.75 437.5  875 
2.5 -7.2 0.3  10.3 22.8 50 75 250 500 1000 
2.75 -6.263 2.175  13.425 27.488 56.25 84.375 281.25 562.5  1125 
3 -5.325 4.05  16.55 32.175 62.5 93.75 312.5  625  1250 
3.25 -4.388 5.925  19.675 36.863 68.75 103.125 343.75 687.5  1375 
3.5 -3.45  7.8  22.8 41.55 75 112.5 375 750 1500 
3.75 -2.513 9.675  25.925 46.238 81.25 121.875 406.25 812.5  1625 
4 -1.575  11.55  29.05  50.925 87.5 131.25 437.5  875  1750 
4.25 -0.637  13.425  32.175  55.613 93.75 140.625 468.75 937.5  1875 
4.5 0.3  15.3  35.3 60.3  100 150 500 1000 2000 
 
12 MONTH LIMITED WARRANTY 
 
Advanced Engine Management Inc. warrants to the consumer that all AEM High Performance products will be free from defects in material and 
workmanship for a period of twelve (12) months from date of the original purchase. Products that fail within this 12-month warranty period will be 
repaired or replaced at AEM’s option, when determined by AEM that the product failed due to defects in material or workmanship. This warranty is 
limited to the repair or replacement of the AEM part. In no event shall this warranty exceed the original purchase price of the AEM part nor shall AEM be 
responsible for special, incidental or consequential damages or cost incurred due to the failure of this product.  Warranty claims to AEM must be 
transportation prepaid and accompanied with dated proof of purchase. This warranty applies only to the original purchaser of product and is non-
transferable. All implied warranties shall be limited in duration to the said 12 month warranty period. Improper use or installation, accident, abuse, 
unauthorized repairs or alterations voids this warranty. AEM disclaims any liability for consequential damages due to breach of any written or implied 
warranty on all products manufactured by AEM. Warranty returns will only be accepted by AEM when accompanied by a valid Return Goods 
Authorization (RGA) number.  Product must be received by AEM within 30 days of the date the RGA is issued. 
Please note that before AEM can issue an RGA for any product, it is first necessary for the installer or end user to contact the AEM Performance 
Electronics tech line at 1-800-423-0046 to discuss the problem.  Most issues can be resolved over the phone.  Under no circumstances should a system 
be returned or a RGA requested before the above process transpires. Figure 1.  Connector Assembly Showing Pull to Seat Terminal