AEG Su 96040 5i Operating And Installation Instructions

							
Installation
11

1xA
2xD
1xB
2xC
2xL
18xI
2xF 2
xG
1xK
1
Installation kit

Two cabinet securing brackets are supplied with the installation pack.
They need to be assembled onto the cabinet prior to cabinet being
pushed into the Kitchen aperture.

1. To fit these brackets remove the two
screws at the top left and right
hand front corners of the cabinet.
2. Position the two brackets 
as shown in the figure and
replace the two securing
screws.
2
a)
Left hand bracket Right hand bracket2
b)
 
						

							
Installation
12
Push the appliance
into place. The plug
socket necessary for
connection of the
appliance to the elec-
tricity supply should 
be positioned, so that
the plug is not placed
in the recess.
3. To adjust the height
proceed as follows:
Loosen or tighten the
two front feet.
The rear feet are adjusted by turning the screw in the front kick plate
to the left or right.

596
555
max
+
-
3
+
-
max. 890 mm
4.The joint cover (B) is to be
assembled after having installed
the appliance in the recess.





 
						

							


Installation
13
6.To mount the furniture door
proceed as shown in the fig-
ures:
5.Push the appliance
into place and retain
the cabinet with
screws  (I)through the
securing brackets into
the worktop or adja-
cent woodwork as
necessary.














\b 	
\b 

 \f


 
						

							
Installation


\b	
\b	







\f



\b	
\f


Upper part of kitchen 
furniture panel
\b


\f






\b	


\b


14
 
						

							
	
\b\b



\b

Installation
15








\b
	




7.Refit the covering strip.
 
						

							
Installation
16
Fitting the plinth
Important!
For the efficient operation of the appliance, it is important that the
original ventilation grid is used. For an opening height dimension A=820 mm and a plinth height
dimension a=100 mm, the plinth may
be fitted without adjustments. The
same applies to an opening height
dimension B=890 mm and a plinth
height dimension b=170 mm.
 For plinth heights greater than  a=100 mm, b=170 mm, a cut should
be made in the plinth, 580 mm wide,
in the centre of the appliance posi-
tion, leaving a remaining height of
a=100 mm, b=170 mm.
 Attach plinth to the kitchen units.
Important!
The plinth must be positioned at a minimum distance of 25 mm from
the door.
Please check whether, after installing your appliance and especially
after reversing the door, the door seal seals right round. A badly fitting
door seal may lead to heavy frosting and result in a higher power con-
sumption (see also “What to do if ...”).

580
a = 100
b = 170
25 - 80
A = 820
B = 890
25DO008b
Power supply
A correctly installed, earthed socket is required for the electrical sup-
ply. The supply must have a fuse rating of at least 10 Amps. If the
socket is not accessible once the appliance is built in, the electrical
installation must include suitable means of isolating the appliance
from the mains (e.g. a fused spur).
Before initial start-up, refer to the appliance rating plate to ascertain
if supply voltage and current values correspond with those of the
mains at the installation location.
e.g.: AC 220 ... 240 V 50 Hz or
220 ... 240 V ~50 Hz
(i.e. 220 to 240 volts alternating current, 50 Hertz)
The rating plate is inside the appliance on the  right.


 
						

							
Installation
The mains cable may only be changed by a qualified electrician or
competent person. If your appliance needs repairing, please contact
your local AEG Service Force Centre.
Electrical Connection
Any electrical work required to install this appliance should be carried
out by a qualified electrician or competent person.
WARNING – THIS APPLIANCE MUST BE EARTHED
The manufacturer declines any liability should these safety mea-
sures not be observed.
Before switching on, make sure the electricity supply voltage is the
same as that indicated on the appliance rating plate. The rating plate is
inside, on the right.
The appliance is supplied with a 13 amp plug fitted. In the event of
having to change the fuse in the plug supplied, a 13 amp ASTA
approved (BS 1362) fuse must be used.
Important
The wires in the mains lead are coloured in
accordance with the following code:
Green and Yellow Earth
Blue Neutral
Brown Live
As the colours of the wires in the mains lead
of this appliance may not correspond with
the coloured markings identifying the termi-
nals in your plug, proceed as follows:
1.The wire coloured green and yellow must be connected to the termi-
nal marked with the letter “E” or by the earth symbol  or coloured
green and yellow.
2.The wire coloured blue must be connected to the terminal marked
“N” or coloured black.
3.The wire coloured brown must be connected to the terminal marked
“L” or coloured red.
4.Upon completion there must be no cut, or stray strands of wire pre-
sent and the cord clamp must be secure over the outer sheath.
Warning! A cut-off plug inserted into a 13 amp socket is a serious
safety (shock) hazard. Ensure that the cut-off plug is disposed of safe-
ty.


 \b !#$
%
& !
%#
\b !
17
 
						

							
18
1 Butter/cheese compartment
2 Sliding shelf
3 Bottle shelf
4 Vegetable drawers
5 Storage shelves
6Thermostat
7 Freezer compartment

➀
➀
➁
➁
➂
➂
➃
➃
➄
➄
➅
➅
\b
\b
Description of the appliance
View of the appliance
Prior to Initial Start–Up
Please clean the appliance interior and all accessories prior to initial\
start-up (see section: “Cleaning and Care”).

 
						

							
19
Starting up and temperature regulation
Important!Only use the appliance when built–in!

1.Connect the appliance to the mains electricity supply.
When the refrigerator compartment door is opened, the internal light-
ing is switched on.
The temperature  controlknob is
located on the right hand side of the
refrigerator compartment.
Setting “0” means: Off.
2. Turn the control knob clockwise past
“1”. The refrigerating unit is now on
and operates automatically.
Setting “1” means:
Hightest temperature, warmest setting.
Setting “6” (end-stop) means:
Lowest temperature, coldest setting.
Note: From a food  safetypoint of view, +5°C for the refrigerator com-
partment and -18°C for the freezer compartment should be con-
sidered cold enough as a storage temperature.
The temperatures in the refrigerator compartment and freezer com-
partment cannot be independently regulated.
At a low ambient temperature of around 16°C, setting “1” should be
selected. At ambient temperatures of around 25°C, select setting “2”.
If you require a lower temperature, select setting “3” or “4”. On this
setting , you can be sure the fresh food placed in the freezer compart-
ment will be reliably frozen and that a storage temperature of -18°C
will be maintained in the freezer compartment.
If you want to freeze fresh food rapidly, select setting “6”, ensuring
that the temperature in the refrigerator compartment does not drop
below 0°C. You should also promptly reset the thermostat knob to set-
ting “3” or “4” after the freezing of the fresh food is complete.
Important!
High ambient temperatures (e.g. on hot summer days) and a cold set-
ting on the thermostat (position”5” to “6”) can cause the \
compressor
to run continuously.
Reason: when the ambient temperature is high, the compressor must
run continuously to maintain the low temperature in the appliance.
The fridge will not be able to defrost since automatic defrosting of the
fridge is only possible when the compressor is not running (see also
Defrosting section). The result is the build up of a thick layer of frost
on the fridge rear wall.


 
						

							
20
If this happens, turn the thermostat knob back to a warmer setting
(position “3” to “4”). At this setting the compressor will be switched on
and off as usual and automatic defrosting recommenced.
Switching off the appliance
To switch off the appliance, turn the temperature regulator to position
0.
If the appliance is not going to be used for an extended period:

1.Remove all refrigerated and frozen packages.
2. Switch off the appliance by turning the thermostat knob to position
0.
3. Remove the mains plug or switch off or disconnect from the electricity
supply.
4. Clean thoroughly (see section: “Cleaning and Care”).
5. Leave the door open to avoid the build up of odours.


Interior Accessories
Storage shelves
Various glass storage shelves are included with your appliance.
The height of the storage shelves can
be adjusted:

1. To do this pull the storage shelf for-
ward until it can be swivelled
upwards or downwards and removed.
2. Please do the same in reverse to
insert the shelf at a different height.